Question about 2005 Chrysler Pacifica

3 Answers

Where can I get a replacement key fob? - 2005 Chrysler Pacifica

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chrysler Master
  • 75,822 Answers
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Www.AutoTransponder.com/Chrysler

www.autotransponder.com


or

  • Call the dealership and ask what sort of key you need. Ask them how long it will take and how much it will cost to replace your key. A couple of hours should be expected, as each coded key still needs to be cut like a standard key. Generally, coded keys cost a little over $100.
  • 2 Call an automotive locksmith if you are unsatisfied with either the price or the time alloted to replace your key through the dealership. Many will come to your car and check your ignition as well as deliver your key in a timely fasion. Automotive locksmiths are best if getting to the dealership is a major inconvenience and may be much cheaper than towing a car with an ignition that needs to be repaired.
  • 3 Order your key. An automotive locksmith may be able to deliver it to you directly on site and will check to see if it is working and service your ignition as well. If you use a dealership, be sure to try the new keys in your Chrysler and make sure that they work. If not, the dealership may have coded the key incorrectly.

  • Posted on Sep 29, 2010

    • Level 2:

      An expert who has achieved level 2 by getting 100 points

      Hot-Shot:

      An expert who has answered 20 questions.

      Corporal:

      An expert that has over 10 points.

      Mayor:

      An expert whose answer got voted for 2 times.

    • Expert
    • 71 Answers

    Unfortunatly the best place to go is the dealer

    Posted on Sep 29, 2010

    1 Suggested Answer

    6ya6ya
    • 2 Answers

    SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

    Hi,
    a 6ya expert can help you resolve that issue over the phone in a minute or two.
    best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
    the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
    click here to download the app (for users in the US for now) and get all the help you need.
    goodluck!

    Posted on Jan 02, 2017

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Program new key fob for Cadillac cts 2003


    There are several methods of doing this - but your 2003 requires that you either go to the dealer for them to add a FOB with special equipment (ask if they'll do it for free - can't hurt). If you have time to kill, you can do it yourself with Method 3 as described and found at:

    Key Fob Reprogramming General Cadillac Forums

    Method 3 - Key Fob Auto Learn


    This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

    Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
    Do not place any known good key fobs in the vicinity of the vehicle when programming with Method 3. If the RCDLR recognizes a known good key fob during Method 3 programming, the programming mode will resort to Method 1.


    The vehicle must be OFF.
    Place the replacement key fob in the console pocket with the buttons facing forward.
    Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
    The DIC will display a message: OFF/ACC TO LEARN.
    Press the OFF/ACC portion of the ignition button.
    The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
    When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
    Repeat steps 5-7 two more times, for a total of 30 minutes.
    The DIC will display a message: OFF/ACC TO LEARN.
    Press the OFF/ACC portion of the ignition button.
    A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
    Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
    If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
    Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.

    Good luck!

    Feb 25, 2015 | 2003 Cadillac CTS

    1 Answer

    My key will not start my car,then it wouldn't open the door


    This model year comes equipped with Keyless Enter-N-Go, which uses an electronic transmitter in the key fob to communicate with the car. The vehicle's doors will not unlock and the vehicle will not start if the key fob is not matched to the vehicle or if the commonly-available watch battery in the key fob has been depleted. The EVIC will flash a message upon vehicle startup if it determines that the battery in your key fob is low on charge and should be replaced.

    To open the doors, try the following:

    1. Use the spare key fob that came with the vehicle. If the battery in your main key fob is depleted, the spare key fob's battery may still retain charge due to its much more occasional use.

    2. The key fob comes with an emergency key inside of it. To remove the emergency key, slide the mechanical latch on the back of the key fob sideways with your thumb and then pull the key out with your other hand. This key will allow you to unlock the driver's side door and glove compartment. It will not start the vehicle.

    To start the car with a severely-depleted key fob battery, try the following:

    1. In case the ignition switch does not change with the push of a button, the RKE transmitter (Key Fob) may have a low or dead battery. In this situation a back-up method can be used to operate the ignition switch. Put the nose side (side opposite of the emergency key) of the Key Fob against the ENGINE START/STOP button and push to operate the ignition switch.

    To replace the battery in your key fob, try the following:

    1. Remove the emergency key from the key fob following the directions above.

    2. Using a vinyl spudger tool or a flat-bladed screwdriver, gently pry the two halves of the key fob apart at the indented slot above the slot for the emergency key.

    3. Replace the depleted battery with a new battery. Use the depleted battery to visually match the size. The battery is usually available wherever watch or hearing-aid batteries are sold.

    4. Snap the key fob back together and replace the emergency key. If the issue is a depleted battery, your key fob should operate normally.

    If the issue is not related to the state of the battery, you will probably need to contact your local dealer for service.

    Source: Owner's Manual, pages 12-17

    http://justgivemethedamnmanual.com/dodge/dodge-charger-owners-manual/

    Mar 01, 2014 | 2011 Dodge Charger

    1 Answer

    I cannot lock or unlock my car with my key fob


    Test the battery inside key fob, should be at 3 volts, if is less than 3 volts replace the battery. If that does not work you may need to replace the key fob, on this vehicle you can program the key fob through the radio, the car manual shows you how to do this.

    Before replacing the old key fob you can try to resinc the fob to the car by pressing the lock and unlock buttons at the same time for about 15 sec, if the door locks cycle the the fob will work again.

    Mar 02, 2013 | 2004 Chevrolet Impala

    1 Answer

    Replaced chip on key on 91 DTS and car lost all power while driving. It shut down and nothing works.


    There are 4 methods for programming key fobs. Up to 4 key fobs may be programmed to the remote control door lock receiver (RCDLR). Each programmed key fob is given a position of #1-#4 in the RCDLR memory.
    Method 1 - Key Fob Quick Learn This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key.

    Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


    The vehicle must be OFF.
    Place a known key fob within the interior of the vehicle.
    Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
    The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
    Place the replacement key fob in the console fob pocket with the buttons facing forward.
    A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.
    If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode.
    Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


    Method 2 - Key Fob Slot Programming

    This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.

    Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


    The vehicle must be OFF.
    Place a known key fob within the interior of the vehicle.
    Install a scan tool.
    Use the scan tool, to access the following:
    • Vehicle Control Systems

    • Computer/Integrating Systems

    • Module Replacement/Setup

    • RCDLR

    • Program Key Fobs

    Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
    Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
    Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
    If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
    Remove the scan tool.
    Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


    Method 3 - Key Fob Auto Learn

    This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

    Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
    Do not place any known good key fobs in the vicinity of the vehicle when programming with Method 3. If the RCDLR recognizes a known good key fob during Method 3 programming, the programming mode will resort to Method 1.


    The vehicle must be OFF.
    Place the replacement key fob in the console pocket with the buttons facing forward.
    Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
    The DIC will display a message: OFF/ACC TO LEARN.
    Press the OFF/ACC portion of the ignition button.
    The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
    When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
    Repeat steps 5-7 two more times, for a total of 30 minutes.
    The DIC will display a message: OFF/ACC TO LEARN.
    Press the OFF/ACC portion of the ignition button.
    A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
    Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
    If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
    Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


    Method 4 - Service Programming System Fob Programming

    This procedure is a 10-minute relearn procedure using the Techline Terminal with SPS software. Once the 10-minute timer has expired, the fobs can be programmed similar to Method 2 using slot programming. A scan tool, Techline Terminal, and a replacement key fob are required to perform this procedure.

    Place the vehicle in the Vehicle On, Engine Off mode.
    Connect a scan tool to the vehicle.
    Insure that all power consuming devices are turned OFF on the vehicle.
    With a scan tool, select Request Info under Service Programming System and follow the scan tool on-screen instructions.
    Disconnect the scan tool from the vehicle and connect the scan tool to a Techline Terminal with the current Service Programming System (SPS) software.
    Turn the vehicle OFF.
    On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions. Ensure the correct programming procedure is selected based on component being replaced or programmed. See Important above.
    Disconnect the scan tool from the Techline Terminal and re-connect the scan tool to the vehicle.
    With a scan tool, select Program ECU under Service Programming System.
    At this point the scan tool must remain connected for the duration of the 10 minute relearn procedure.
    When the 10 minute relearn procedure has completed, use the scan tool to access the following:
    • Vehicle Control Systems

    • Computer/Integrating Systems

    • Module Replacement/Setup

    • RCDLR

    • Program Key Fobs

    Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
    Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
    If programming additional key fobs, repeat steps 12-13, or press the OFF/ACC portion of the ignition switch to exit programming.
    Remove the scan tool.
    Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.

    Oct 26, 2011 | 2006 Cadillac DTS

    2 Answers

    Both key fobs for honda pilot 2006 no longer works. Do I need new keys or is it something internal such as a fuse?


    First thing, does the red light on the remote light up when you push any of the button
    if no, then replace battery inside remote
    if yes, then try repograming the remote to the car again.
    -Have both remote ready. fob#1 and fob#2 (doesn't matter which one is #1 or #2)
    -each step has to be done within 5 sec or it will not work, but don't do it super fast.
    1.turn key just to the "on" position (not starting) and push "lock button " on fob#1 once and release
    2.turn key off
    3.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
    4.turn key off
    5.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
    6turn key off
    7.turn key just to the "on" position (not starting) and push "lock button " on fob#1 twice (if you only have one fob, then stop here and go to step 7)and push the "lock button" on fob#2 twice.
    8.turn key off and remove key from ignition.
    if you did it right, remotes should work again.
    good luck

    Dec 17, 2010 | Honda Pilot Cars & Trucks

    1 Answer

    Keyless entry remote programming


    Hello here is the instructions for programming the key fobs

    This procedure will add, replace, or invalidate all key fobs. This procedure requires that you have a known good key fob available, a new/replacement key fob, the vehicles mechanical key, and a scan tool.
    Method 1 is also used for the initial programming of fobs to a new replacement RCDLR. In this instance, the new RCDLR comes ready to learn the first key fobs introduced. Perform the learn procedure as outlined, with the exception that the new RCDLR does not require a known good key fob be placed within the interior of the vehicle.
    Note: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Methods 2 or 3 must be used in this instance.
    1. The vehicle must be OFF.
    2. Place a known key fob and any new/replacement key fob(s) to be programmed in the cupholder inside the vehicle. DO NOT place any fobs in the console fob pocket at this time.
    3. Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
    4. The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4). → If the DIC displays: OFF/ACC TO LEARN, the known fob has not been recognized. At this time, programming will revert to Method 2.
    5. If the DIC is displaying the correct fob number that needs to be programmed, skip ahead to step 9.
    6. If the DIC is not displaying the correct fob number that needs to be changed (i.e., the DIC is displaying: READY FOR FOB 3, and you wish to program FOB 1), use the scan tool to access the following: • Vehicle Control Systems • Computer/Integrating Systems • Module Setup • Remote Control Door Lock Receiver • Program Key Fobs
    7. Select the fob position you wish to program: Note: Selecting Invalidate All Fobs will erase any known fobs and will cause the DIC to prompt READY FOR FOB 1, requiring all fobs to be relearned to the vehicle.
      • Invalidate All Fobs • Program Fob 1 • Program Fob 2 • Program Fob 3 • Program Fob 4
    8. With the fob position selected, press the PROGRAM soft key on the scan tool. The DIC should display: READY FOR FOB X (X = fob 1, 2, 3 or 4, depending on the selected position)
    9. With the DIC displaying the correct fob position that is to be programmed, place the new/replacement key fob in the console fob pocket with the buttons facing forward.
    10. A beep will occur once the fob has been learned.
    11. If programming additional key fobs and there is no DIC prompt that indicates READY FOR FOB X, repeat steps 7 and 8.
    12. Exit programming mode by pushing the OFF/ACC portion of the ignition switch. Note: Failure to exit programming mode (press OFF/ACC) prior to pressing the UNLOCK button of each key fob programmed will result in that fob being inoperative. Pressing the UNLOCK button completes the programming sequence and is require to ensure transmitter operation.
    13. Press the UNLOCK button on each key fob that was programmed to finalize the programming and confirm system operation.

    Nov 03, 2010 | 2006 Cadillac STS

    4 Answers

    My 2006 cadillac sts key fob all of a sudden is not working it says no fob detected and i have the fob what can b wrong??


    Some late model fobs contain electronics beyond the push buttons.
    Batteries are replaceable...small screws may let you do this.
    If the battery is not the cause....a replacement fob may be expensive. A road service technician can probably troubleshoot and replace cheaper than dealer !

    Sep 07, 2010 | 2006 Cadillac STS

    1 Answer

    How do you charge the key fob.. The message on the dash saya that the key fob battery is low.


    The key fob does not get charged. Instead you replace the battery inside the Fob. if you look behind the fob it tells you what battery it needs for replacement. CR2032

    Dec 29, 2009 | 2005 Cadillac STS

    1 Answer

    Programming a keyless entry remote


    Key Fob Auto Learn
    This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

    Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
    Do not place any known good key fobs in the vicinity of the vehicle when programming. 

    The vehicle must be OFF. 
    Place the replacement key fob in the console pocket with the buttons facing forward. 
    Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds. 

    The DIC will display a message: OFF/ACC TO LEARN. 
    Press the OFF/ACC portion of the ignition button. 
    The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time. 
    When the counter reaches 0, DIC will display OFF/ACC TO LEARN. 
    Repeat steps 5-7 two more times, for a total of 30 minutes. 
    The DIC will display a message: OFF/ACC TO LEARN. 
    Press the OFF/ACC portion of the ignition button. 
    A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2. 
    Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode. 
    If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode. 
    Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation. 

    Good luck and hope this help's keep me posted, there are 3 other methods and the 5th method is a tech 2 scan tool that the dealer uses but this should work on your year of cadillac. 

    Jul 01, 2009 | 2003 Cadillac Deville

    Not finding what you are looking for?
    2005 Chrysler Pacifica Logo

    931 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8195 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...