Question about Chevrolet TrailBlazer

1 Answer

Engine light came on. diagnostis secondary air flow incorrect.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,102 Answers

Hi the problem could be with a sensor or blocked air filter,
check the air filter first as this may need changing but if its ok then you will need to have a diagnostic check done to find out the true cause as you could throw money at it and not find the fault.

it could be something like the mass air flow sensor or even a damaged vacum hose so also check these for splits,

let me know if you need further assistance ok

plz rate this solution as i have a whole page of unrated posts, thanks

Posted on Sep 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does a p0411 code mean?


That code means. Secondary Air Injection System Incorrect Flow.

Feb 24, 2015 | 2009 Chevrolet Chevrolet Impala LT

1 Answer

P0411 secondary air injection incorrect flow on porsche boxster 1998


You have a code to go by & you know codes are
used to diagnose the systems with the fault

It won't go away by it's self & running fine to you
is no guarantee that it will for long or not cause damage

Get it repaired

You can use the internet to research codes & their causes

Nov 13, 2012 | 1998 Porsche Boxster

1 Answer

Check engine light reads...po411...or, secondary air injection system-incorrect flow...what does this really mean???


sounds to be low air flow. Check filter . could be a faulty mass air flow sensor. good luck

Nov 05, 2012 | 1998 Ford Mustang

1 Answer

How to clean secondary air injection incorrect upstream flow detected Code PO411


The valve may need to be replaced. Only air flows thru the components.

Jul 03, 2012 | 2008 Chevrolet TrailBlazer LT

1 Answer

Engine light stay on and the code reading po411....what does that mean and how can i fix it?


P0411 is Secondary Air Injection (AIR) Incorrect Air Flow Detected. Without knowing what year/Model and engine you have it's a guess as to the proper fix.

Apr 26, 2011 | Chevrolet TrailBlazer Cars & Trucks

2 Answers

What is scanner code PO411


code po411 secondary air injection system incorrect flow,possible causes , faulty air pump or faulty air pump vacuum valve or faulty check valve.

Apr 06, 2011 | 1999 Volkswagen Cabrio

1 Answer

I have a 2001 VW Jetta 1.8T. The check engine light came up and the codes that came up were P0171 (System too lean, meaning there is too much oxygen in the exhaust). And P0411 (Secondary air injection...


problem is bad AIR FLOW sensor! I am replaced in my 1.8T PASSAT with tuning chip 6.pcs air flow sensors over 3 years !!!!! All VW cars have a air flow problem!!!!! And not only this!!

Nov 15, 2010 | 2002 Volkswagen Passat

2 Answers

Obd code of p0411 on a 1999 ford mustang 3.8 v-6 what do I check to correct


That's s failure of the secondary air pump. It'll have to be changed. It's an emissions component meant to help with cold start emissions. It won't cause engine running trouble but at inspection time you'll fail for smog. Change it before then and you'll be fine.

May 16, 2010 | 1999 Ford Mustang Cobra

1 Answer

Check engine light p0411 code what must i do car drive with lack of power. I push the acceleration pedal and it takes seconds befor it accelerate, like it dont take off.


this has to do with your secondary air injection incorrect flow. start looking for a vacuum leak especially around the air duct from the mass air flow sensor to the throttle body.

Jan 25, 2010 | 2003 Volkswagen Passat

1 Answer

Vw passat 2000 1.8t front wheel drive


please rate me solved...thanks

DTC P0411/16795: SECONDARY AIR SYSTEM - INCORRECT FLOW DETECTED
Test Requirements
Ensure all fuses are okay, battery voltage is at least 11.5 volts, all electrical accessories are off, A/C is off.
Ensure engine is mechanically sound.
Test Procedure

NOTE
Secondary air system is activated by ECM and blows air into exhaust pipe
upstream of catalytic converter for 100 seconds during a cold start, 41-91°F (5-
33°C). Engine must be cold to perform following test procedure.

1. Ensure fuse and secondary fuse (secondary fuse is 40 amp and is located in fuse holder on top of battery)
are okay. Check hoses and components of Secondary Air Injection System, for damage, loose fit and
improper installation, check vacuum hoses for Secondary Air Injection System. Repair as necessary.
Erase DTC memory. Verify repair. If DTC does not reset, test is complete. Perform ECM relearn
procedure. See TEST DRIVE RELEARN PROCEDURE .
2. Remove engine cover. Disconnect pressure hose from Secondary Air Pump Motor (V101), by pressing
buttons on hose connector. See Fig. 33 . Using scan tool, check Secondary Air Pump Motor (V101) in
scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See OUTPUT
DIAGNOSTIC TEST MODE .
3. Secondary Air Pump Motor (V101) should run in intervals and air should exit pump at hose connection.
If Secondary Air Pump Motor (V101) is okay, go to step 7 . If motor runs and no air exits secondary air
pump motor, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE . If
secondary air pump motor does not run, go to next step.
4. Disconnect Secondary Air Pump Motor (V101) harness connector, install LED test light at secondary air
pump harness connector terminals. Turn ignition on. Using scan tool, activate Secondary Air Pump Motor
(V101) in scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See
OUTPUT DIAGNOSTIC TEST MODE . LED test light at Secondary Air Pump Motor (V101) harness
connector should flash. If LED test light at Secondary Air Pump Motor (V101) harness connector does
not flash, go to next step. If LED test light at Secondary Air Pump Motor (V101) harness connector
flashes, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test is
complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
5. Using DVOM check resistance of Secondary Air Pump Motor (V101) wiring. See appropriate WIRING
DIAGRAM under ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS. Resistance should
be a maximum of 1.5 ohms for each reading. Check wiring for short circuit to one another in Secondary
Air Pump Motor (N101) harness connector. Repair as necessary. Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure.
Secondary Air Pump Motor (N101) wiring is okay, go to next step.
6. Check Secondary Air Pump Relay (J299) and Secondary Air Pump Relay (J299) wiring. See DTC
P0418/16802: SECONDARY AIR PUMP RELAY (J299), MALFUNCTION . Repair or replace as
necessary. Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure. See
TEST DRIVE RELEARN PROCEDURE .
7. Disconnect vacuum hose from Secondary Air Injection Valve (N112) and disconnect pressure hose from
secondary air pump motor, press buttons on pressure hose connector to disconnect pressure hose. See Fig.
34 . Blow lightly into disconnected pressure hose, Combi-Valve should be closed. Connect hand vacuum
pump to disconnected vacuum hose and apply vacuum to Combi-Valve, Combi-Valve should open. If
Combi-Valve opens when vacuum is applied, Combi-Valve is okay. Go to next step. If Combi-Valve
does not open when vacuum is applied, replace faulty Combi-Valve. Erase DTC memory. Verify repair.
Test is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
8. Check Secondary Air Injection Valve (N112). See DTC P0412/16796: SECONDARY AIR
INJECTION VALVE (N112), ELECTRICAL CIRCUIT MALFUNCTION . Repair as necessary.
Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure.
NOTE: Do not use compressed air to check Combi-Valve.
2000 Volkswagen Passat GLS
2000 ENGINE PERFORMANCE Self-Diagnostics - 1.8L Turbo

Jun 21, 2008 | 2000 Volkswagen Passat 4Motion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...