Question about Mercedes-Benz C-Class

1 Answer

How to change headlamp. - C-Class Mercedes-Benz Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Mercedes-Benz Expert
  • 166 Answers

On most of the Mercedes in order to change the complete headlamp assembly you need to pull off the front bumper in order to expose the screws on the side of the housing and also for clearance so that you don't scratch up the bumper.

Posted on Oct 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a headlight on a 1997 gmc sierra


Headlamp Removal & Installation To Remove:
  1. Turn headlamp switch OFF. gm-06-00-1046.gif

  2. Remove retaining ring screws.
  3. Remove retaining ring from headlamp.
  4. Remove headlamp from headlamp mounting bracket.
  5. Disconnect electrical connector from headlamp.
To Install:
  1. Connect electrical connector to headlamp.
  2. Install headlamp to headlamp mounting bracket.
  3. Install retaining ring to headlamp and install screws.
prev.gif next.gif

Feb 06, 2011 | 1997 GMC Sierra

1 Answer

How do you change the headlamp on a 2008 mailbu?


dcramer531_8.gif Remove the front bumper fascia upper bracket. Refer to Front Bumper Fascia Bracket Replacement .
1
Headlamp Screw (Qty: 2)
Notice: Refer to Fastener Notice in the Preface section.
Tip
Secure the headlamp fasteners in sequence, as indicated.
Tighten
3 N·m (27 lb in)
2
Headlamp Assembly
Procedure
  1. <LI type=1>Pull forward on the outside edge of the headlamp in order to release the up and down locator tabs on the backside of the headlamp. <LI type=1>Pull forward on the top inside edge of the headlamp to release the inboard up/down locator. <LI type=1>Pull the headlamp assembly down. <LI type=1>Pull the headlamp assembly forward far enough to access the electrical connection. <LI type=1>Disconnect the headlamp electrical connector from the forward lamp harness connector. <LI type=1>Remove the headlamp assembly.
  2. Aim the headlamps after installation. Refer to Headlamp Aiming .

Jan 07, 2011 | Chevrolet Malibu Cars & Trucks

1 Answer

Need help changing out the low beam on drivers side of 2006 buick rainier


Removal & Installation
Bulb Replacement
To Remove:

CAUTION
Halogen bulbs contain pressurized gas.
Mishandling a bulb may result in the bulb shattering into flying glass
fragments.

CAUTION
Make sure to wear eye protection when
handling a halogen bulb.

CAUTION
Do not touch the glass of a halogen bulb,
only handle the bulb by the base.

CAUTION
Do not allow a halogen bulb to come into
contact with dirt or moisture.

CAUTION
Make sure to dispose of a used halogen bulb
properly.

CAUTION
Do not allow children to handle halogen
bulbs.


  1. Turn the lamp switch to the off position.
  2. Make sure the bulb is cool before changing.
  3. Remove the headlamp assembly from the headlamp panel.
  4. Remove the rear access cover from the headlamp assembly.
  5. Disconnect the headlamp connector.
  6. Remove the bulb from the headlamp assembly by rotating the bulb and socket
    counterclockwise.

To Install:


  1. Connect the headlamp connector.
  2. Install the bulb into the headlamp assembly by rotating the bulb and socket
    clockwise.
  3. Install the rear access cover onto the headlamp assembly.
  4. Install the headlamp assembly into the headlamp panel.

Headlamp Assembly
Chevrolet
To Remove:






Headlamp Assembly (Chevrolet)
gm-06-00-1591.gif




  1. Remove the grille from the front of the vehicle.
  2. Release the headlamp assembly retaining tabs.
  3. If equipped, disconnect the headlamp leveling motor connector.
  4. Disconnect the headlamp connector.
  5. Remove the park/turn and side marker bulb sockets from the headlamp
    assembly.
  6. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. Install the park/turn and side marker bulb sockets into the headlamp
    assembly.
  3. Connect the headlamp connector.
  4. If equipped, connect the headlamp leveling motor connector.
  5. Lock the headlamp assembly retaining tabs.
  6. Install the grille onto the front of the vehicle.

GMC, Oldsmobile, Buick, Isuzu, and Saab
To Remove:






Headlamp Assembly (GMC, Saab, Oldsmobile, and Buick)
gm-06-00-1590.gif




  1. Release the headlamp assembly retaining tabs.
  2. Disconnect the headlamp connector.
  3. Remove the park/turn bulb socket from the headlamp assembly.
  4. For GMC, Saab, Oldsmobile, and Isuzu vehicles, remove the side marker bulb
    socket from the headlamp assembly.
  5. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. For GMC, Saab, Oldsmobile, and Isuzu vehicles, install the side marker bulb
    socket into the headlamp assembly.
  3. Install the park/turn bulb socket into the headlamp assembly.
  4. Connect the headlamp connector.
  5. Lock the headlamp assembly retaining tabs.


prev.gif next.gif

Oct 28, 2010 | 2006 Buick Rainier

1 Answer

How do you change the headlight on a 2006 grand prix


  1. Raise the hood.
  2. Lift upward on the headlamp retainer (1).
  3. Pull the headlamp assembly outward enough to release the headlamp assembly from the upper fascia support.
  4. Position the headlamp assembly away from the vehicle body to access the electrical connector
    1. Disconnect the electrical connector from the headlamp assembly.
    2. Remove the headlamp assembly from the vehicle.
    3. Use caution handling halogen bulbs. Remove the headlamp bulb/socket from the headlamp, by turning counterclockwise. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.
    4. Remove the headlamp bulb/socket from the headlamp assembly.450a6d8.gif

May 06, 2010 | 2006 Pontiac Grand Prix

1 Answer

I need to change the headlight i don't know how


You must first remove the Headlamp bezel which is the chrome trim that surrounds the duel headlamp housing. The chrome trim surround is mounted to the Headlamp mount panel with three nuts which you can only access on the inside. Pop open the hood and look on the inside near were the headlamp bulbs are. You will see the three mount nuts for the headlamp bezel. Might be rusty so first give it a shot of WD40 or similar. Remove the nuts and then you can lift the headlamp bezel from the outside away from the headlamp bulbs. The headlamp bezel only has tabs that slid into a slot on the bottom so you can left out once the top three nuts are removed. Once the headlamp bezel has been removed you can then access the 4 screws that hold the headlamp trim ring in place which is what holds the headlamp bulb in place. Remove this ring and then unplug the headlamp from the back and replace the headlamp. Should take you less than 5 or 10 minutes. Dan

Aug 09, 2009 | 1989 Lincoln Town Car

1 Answer

I have 2006 Grand Prix How do I change head lamp?


Caution Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury:
Turn off the lamp switch and allow the bulb to cool before changing the bulb.
Leave the lamp switch OFF until the bulb change is complete. Always wear eye protection when changing a halogen bulb. Handle the bulb only by its base. Avoid touching the glass. Keep dirt and moisture off the bulb. Properly dispose of the used bulb. Keep halogen bulbs out of the reach of children.
Raise the hood.
Remove the headlamp assembly bolts from the upper fascia support.
Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support.
Position the headlamp assembly away from the vehicle body to access the electrical connector.
Disconnect the electrical connector from the headlamp assembly.
Remove the headlamp assembly from the vehicle.
Disconnect the electrical connector from the headlamp bulb/socket.
Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise.
Remove the headlamp bulb/socket from the headlamp assembly.

Jun 13, 2009 | 2006 Pontiac Grand Prix

1 Answer

How do i change both headlights on my 2002 chevy cavillier


Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Hood close out filler panel.
    • Bolts from the headlamp.
    • Headlamp from the headlamp mounting panel.
    • Electrical connector from the headlamp.
    • Headlamp bulb/socket retainer ring from the headlamp.
c218bc4.gif

  • Headlamp bulb/socket from the headlamp.
  • Bolts from the headlamp adjuster mechanism.
  • Headlamp adjuster mechanism.
  • To Install:
    1. Install or connect the following:
      • Headlamp bulb/socket to the headlamp.
      • Headlamp bulb/socket retainer ring to the headlamp.
      • Headlamp adjuster mechanism to the headlamp housing, if necessary
      • Bolts to the headlamp adjuster mechanism. Tighten to 6 N.m (53 lb in).
      • Electrical connector to the headlamp.
      • Headlamp to the headlamp mounting panel and lower mounting bracket.
      • Bolts to the headlamp. Tighten to 10 N.m (89 lb in ).
      • Hood close out filler panel.

    Jun 06, 2009 | 2002 Chevrolet Cavalier Coupe

    1 Answer

    I need to change the headlamp bulb.


    1. Disconnect and isolate the battery negative cable.
    2. Remove screws attaching headlamp module to upper crossmember.
    3. Remove headlamp module from vehicle.
    4. Disconnect wire connector from back of headlamp.
    5. Remove bulb from headlamp unit.
    INSTALLATION

    CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

    1. Connect wire connectors to the back of headlamp module.
    2. Place headlamp module in position.
    3. Install screws attaching headlamp module to upper crossmember.
    4. Connect battery negative cable.

    Mar 21, 2009 | 2003 Dodge SRT-4

    1 Answer

    Hi, I have a 99 mercury cougar and I need to change the headlights. I am having difficulty finding the electrical connector so that I can pull the headlight assembly out and change the lights. Where is...


    Headlamp Bulb Removal
    1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly .

    Headlamp Assembly Removal
    1. Remove the radiator grille.7feecfa.gif

    Remove the headlamp assembly.
    2b42ecf.gif
    remove the cover/
    1. f76b11b.gif
    3.
    sxu~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not touch the glass of the bulb with your fingers.
    Remove the headlamp bulb (low beam bulb shown). 79891b8.gif

    Jan 10, 2009 | 1999 Mercury Cougar

    1 Answer

    High beam bulb blown on buick rendezvous


    1. Open the hood.
    2. Remove the thumb screw from the back of the headlamp.
      761252.gif
      tif.gif
    3. Release the headlamp retainer by lifting up.
      755085.gif
      tif.gif
    4. Pull the headlamp straight forward, to release the ball stud from the grommet.
    5. Remove the headlamp from the upper fascia support.
    6. Disconnect the electrical connector from the headlamp.
      761255.gif
      tif.gif
    7. Remove the bulb(s) from the headlamp by rotating counterclockwise.
      761257.gif
      tif.gif
    8. Release the headlamp trim tabs from the headlamp, if required.
      761253.gif
      tif.gif
    9. Remove the headlamp trim from the headlamp, pulling to release the adhesive tape.
    10. Clean adhesive from the headlamp trim and headlamp using 3M™ adhesive remover P/N 8984, or equivalent.

    Nov 26, 2008 | 2003 Buick Rendezvous

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    68 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mercedes-Benz Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    yadayada
    yadayada

    Level 3 Expert

    74945 Answers

    Michael Contreras
    Michael Contreras

    Level 2 Expert

    166 Answers

    Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...