Question about Nissan Minivan

1 Answer

I have a Nissan caravan qd and i changed the pressure plate since then it has a vibration when it goes for a while. what might be the cause?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Nissan Master
  • 1,026 Answers

Make sure your drive shaft is lined up properly

Posted on Sep 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pressure plate torque


I have seen this problem many times, people change clutches but don't machine the fly wheel. this causes a shudder or the other thing is a crack in the fly wheel or pressure plate, sorry but transmission out fly wheel off to be machined, new clutch and pressure plate

Dec 04, 2013 | Cars & Trucks

1 Answer

Vibration when rolling


your dust plate is been bent and touches on turning jack up the wheel and straighten the plate...problem will be solved..

Apr 18, 2013 | 1991 Nissan Pickup

1 Answer

2006 nissan frontier low oil pressure at idle after timing chain replacement


I have just spent $1500.00 to fix this low oil pressure problem. The main cost was having the timing chain replaced and where the oil pressure problem was found. The low oil pressure problem is caused by a bad gasket that is under a plate inside the timing chain cover. The dealer wanted to replace the whole housing as Nissan dose not offer a new gasket and wants you to replace the inner timing chain housing. The plate covers part of the oil gallery, the gasket breaks out from this plate and that is where the oil pressure goes. The gasket can be replaced by removing the plate and making a new gasket. Note getting to the plate inside the timing cover is a major labor issue that takes about 12 hours to complete start to finish. I had to fabricate the gasket my self as the dealer would not. Cost for fixing the bad gasket was about $17.00 for materials. Replacing the timing chain was at my request as it was making noise.

Jan 27, 2012 | Cars & Trucks

1 Answer

Manuel trans shifter tough too shift


if you getting a good pressure from the clutch pedal, change out the shifter bushing, that will help some. if you get a poor pressure from the clutch pedal, pressure plate has weaken, need to change out you pressure plate, throw out bearing, since your in the clutch system i would change out the pad also. Old vehicle and high miles, heavy trucks, its common. also check the slave cylinder, make sure it good working operations. worn rubber seal inside slave cylinder will cause a blow-by when press down the pedal therefore, causing to have a weak clutch pedal and hard to shift/engage into gear, same way goes for weak pressure plate. Good luck!!

Nov 09, 2011 | 1994 Isuzu Rodeo

1 Answer

I replaced the clutch,pressure plate and throw out bearing had my tires balanced and i am still getting excessive viberation on the rear of the truck. 1997 nissan xe standard shift


When you have vibration like that its normally caused by a tire either out of balance or the belts in the tire have separated. They should have noticed this if they balanced them. You could try rotating the tires to see if the vibration moves to the front. If you are still having this issue it could be a bad shock or both. Or it could be something in the differential that is going bad.
I kinda doubt that it could be a differential issue because you would probably notice performance issues and it would whine or make some sort of noise.

Jun 17, 2011 | 1997 Nissan Pickup

1 Answer

Cross bearing wornout my nissan caravan


Nothing has to be done at the dealer,unless you like to spend more money..
What part are you referring to?
Do you not have a shop that you regularly take your vehicles to?

May 03, 2010 | 1997 Nissan Maxima

1 Answer

Pick up seems to drag/vibrate esp at 1st gear even though the ff. have been replaced: release bearing, clutch disk, pressure plate, transmission support, center bearing and cross joints. gear oil are all...


My 96 Nissan 4x4 did this especially in first and in second as well if accelerating hard and also more pronounced if hauling heavy items. It turned out that the front yoke on the driveshaft linking the transfer case with the front differential was rusted and frozen to the portion of the driveshaft on which it is supposed to slide. If your truck is not four-wheel-drive this will not be the cause of your vibration. If your truck is 4x4 and this is the cause of your vibration and it has been doing it for a while, check your engine mounts as the vibration can damage/break them--especially the left one.

Dec 19, 2009 | 1996 Nissan Pickup

1 Answer

Clutch won't release on 92 Nissan P/U. Changed Clutch Master Cylinder and slave. Bled system. Have good travel on slave cylinder but still does not release the clutch when the pedal is pushed?


If the vehicle has been standing for some time (6 months or more) without use, the clutch plate facings may be 'stuck' to the flywheel and pressure plate surface.
To check/clear this problem:-
(with the engine not running!)
hold clutch pedal down - then from under vehicle, find an opening in the clutch bellhousing (such as a water drain slot) where you can see/access the edge of the clutch plate (sandwiched between the pressure plate and flywheel).
Use a screwdriver blade (or similar tool) to prise clutch plate free from flywheel face (only small movement is required).
If the above is not the cause of your problem, 1) the clutch throwout mechanism should be examined for problems,
2) the pressure plate is faulty- may need to be replaced.

Aug 29, 2009 | 1992 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...