Question about Hyundai Sonata

2 Answers

When decelerating through 1000-1200 RPM, headlights, A/C, and sometimes radio go off for about three or four seconds, then come back on when RPM is below 1000. I cannot cause this to happen when car is sitting still, but only when moving. Problem occurs regardless of whether or not brakes are applied. Local Hyundai dealership replaced alternator and battery, with no effect on problem. They then re-flashed computer with no effect. They then said that the anti-moisture grease on brake light bulbs was the culprit, then that it was the after-market brake light bulbs themselves. They replaced all bulbs, and the problem continues. Local mechanic thinks it may be body control module or a bad/loose ground, but has not been able to find problem. Anothr local Hyundai dealer thinks it may be a ground issue, also.

Posted by on

  • amosmc966 Sep 30, 2010

    Mechanic cannot find a loose ground. He also says that a defective body control module should be causing the problem at all speeds/RPMs, and not just in the narrow 1000-1200 RPM range, and not just when slowing down.

  • amosmc966 Sep 30, 2010

    Where do you "add a ground"?

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

HI! It's definitely a ground issue. If the BCM is not faulty then you may need to add an additional ground. Since battery and alternators are new there shouldn't be a problem. Have an additional ground installed and you'll be good. Hope this helps and thank you for using FixYa!

Posted on Sep 30, 2010

  • dj_relly999
    dj_relly999 Sep 30, 2010

    From the negative connector of the battery attached to the body.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,382 Answers

Hi, check the ground wires to make sure they are in place and making good contact, especially the battery cable ground connection to the motor, if this checks out okay, then you have to check out the body control module as said by the local mechanic.
This solution lies within the two options suggested above by me and the local mechanic and local dealer. It's a very rear and difficult problem ti fix....

Posted on Sep 29, 2010

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The radio in my 2000 Pontiac Montana says locked


1. Turn the ignition ON (The radio should display "LOC")
2. Hold down the Radio Presets 2 and 3 buttons for six seconds
3. The radio display changes from LOC to a three-digit number. Write this number down. You now have fifteen seconds to complete the next step.
4. Press the AM/FM button
5. The radio display changes to another three-digit number. Write this number to the right of the first one.
6. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05
7. Call 1-800-537-5140 (talk to a machine)
8. Press 1 then # (pound). You'll hear "Invalid Code, try again"
9. Press 139010 or 106010 or 206010 or 202107 then # (pound). You will be asked to enter your four or six digit code followed by *
10. Enter the number from STEP 6 then *
11. Listen to the four-digit number and write it down. It will be repeated twice
12. Turn the ignition ON (The radio displays LOC)
13. Use the MN and HR buttons to enter the code from STEP 11
14. Press the AM/FM button. The radio display changes to "SEC". Your radio is now "un-locked" and usable.
15.



Dealership Codes
202108
206053
620529

Sep 23, 2014 | 2000 Pontiac Montana

1 Answer

My car stereo is locked how i open it


Requirements

The theft lock radio must be in "LOC" mode.

Procedure:

1. Turn the ignition ON (The radio should display "LOC")
2. Hold down the Radio Presets 2 and 3 buttons for six seconds
3. The radio display changes from LOC to a three-digit number. Write this number down. You now have fifteen seconds to complete the next step.
4. Press the AM/FM button
5. The radio display changes to another three-digit number. Write this number to the right of the first one.
6. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05
7. Call 1-800-537-5140
8. Press 1 then # (pound). You'll hear "Invalid Code, try again"
9. Press 139010 or 106010 or 206010 or 202107 then # (pound). You will be asked to enter your four or six digit code followed by *
10. Enter the number from STEP 6 then *
11. Listen to the four-digit number and write it down. It will be repeated twice
12. Turn the ignition ON (The radio displays LOC)
13. Use the MN and HR buttons to enter the code from STEP 11
14. Press the AM/FM button. The radio display changes to "SEC". Your radio is now "un-locked" and usable.

Jun 07, 2014 | 2007 Chevrolet Silverado Classic SS New...

1 Answer

The radio is locked on a 1995 oldsmobile 88


How to Unlock a Chevy Radio Step 1: Start the vehicle and turn on the radio.
Step 2: Press and hold preset numbers 2 and 3 until a three digit code appears on the radio display. Write this code down.
Step 3: Press the AM/FM button. Your radio will display a second three digit code. Write the second code down. You will now have a six digit code.
Step 4: Call the Chevy Radio Code phone line at 1-800-537-5140.
Step 4: Enter 106010 followed by the # key to direct you to the radio code retrieval system.
Step 5: Enter the six digit code you retrieved in steps 2 and 3 followed by the * key. They must be in order. You will be given a four digit radio code. Write down the radio code.
Step 6: Start your vehicle and turn on the radio. Using the Minute and Hour buttons, enter in the four digit radio code to your stereo system. Press the AM/FM button to unlock your stereo.
How to Unlock a GM Radio Step 1: Start the vehicle and turn on the radio. The radio will display "LOC" indicating the Theftlock system is activated.
Step 2: Press and hold preset buttons 1 and 4 for ten seconds. (If you don't have a fourth preset button, press and hold presets 2 and 3.) The radio will display a three digit number. Write this number down.
Step 3: Press the AM/FM button. Your radio will display a second three digit code. Write the second code down. You will now have a six digit code.
Step 4: Contact your local GM Dealer and give them the six digit code. They will give you a four digit radio code.
Many dealers will give you your radio code for free, while others may charge a small fee. If your dealer is charging a larger fee, consider calling another dealer or doing a Google search for sites offering GMC Radio codes. They usually charge a small (around $10) fee.
Step 5: Start your vehicle and turn on the radio. Press the Hour button on the radio until the first two number of the code appear. Next, press the Minute button until the last two numbers of the code are displayed. Once all four digits appear, press the AM/FM button to unlock your stereo. The display will read "SEC" indicating you have successfully unlocked your radio and it is fully operational.
If radio display reads "INOP" while the vehicle is on, too many incorrect radio codes have been entered. To remove "INOP" from your display and unlock your radio, you must leave the key in the On position for one hour. Once you've retrieved your radio unlock code, write it down for future use. Your radio code will not change and having it handy will save from going from the radio code retrieval process again.

Jan 30, 2014 | Cars & Trucks

2 Answers

My 2008 chevy uplander , had to change radio (cd player not working) now radio is locked, how can I unlock it?


Try this: How to Unlock a Chevy Radio Step 1: Start the vehicle and turn on the radio.
Step 2: Press and hold preset numbers 2 and 3 until a three digit code appears on the radio display. Write this code down.
Step 3: Press the AM/FM button. Your radio will display a second three digit code. Write the second code down. You will now have a six digit code.
Step 4: Call the Chevy Radio Code phone line at 1-800-537-5140.
Step 4: Enter 106010 followed by the # key to direct you to the radio code retrieval system.
Step 5: Enter the six digit code you retrieved in steps 2 and 3 followed by the * key. They must be in order. You will be given a four digit radio code. Write down the radio code.
Step 6: Start your vehicle and turn on the radio. Using the Minute and Hour buttons, enter in the four digit radio code to your stereo system. Press the AM/FM button to unlock your stereo.
How to Unlock a GM Radio Step 1: Start the vehicle and turn on the radio. The radio will display "LOC" indicating the Theftlock system is activated.
Step 2: Press and hold preset buttons 1 and 4 for ten seconds. (If you don't have a fourth preset button, press and hold presets 2 and 3.) The radio will display a three digit number. Write this number down.
Step 3: Press the AM/FM button. Your radio will display a second three digit code. Write the second code down. You will now have a six digit code.
Step 4: Contact your local GM Dealer and give them the six digit code. They will give you a four digit radio code.
Many dealers will give you your radio code for free, while others may charge a small fee. If your dealer is charging a larger fee, consider calling another dealer or doing a Google search for sites offering GMC Radio codes. They usually charge a small (around $10) fee.
Step 5: Start your vehicle and turn on the radio. Press the Hour button on the radio until the first two number of the code appear. Next, press the Minute button until the last two numbers of the code are displayed. Once all four digits appear, press the AM/FM button to unlock your stereo. The display will read "SEC" indicating you have successfully unlocked your radio and it is fully operational.
If radio display reads "INOP" while the vehicle is on, too many incorrect radio codes have been entered. To remove "INOP" from your display and unlock your radio, you must leave the key in the On position for one hour. Once you've retrieved your radio unlock code, write it down for future use. Your radio code will not change and having it handy will save from going from the radio code retrieval process again.

Dec 10, 2012 | 2008 Chevrolet Uplander

1 Answer

Battery indicator light comes on above idle RPM, gauges start fluctuating.


The first thing you need to know is what the alternator output is when this starts happening.
It could be a faulty connection in the wiring harness, or a bad ground connection, or a failing alternator.

Aug 25, 2012 | 2000 Mercury Cougar

1 Answer

Drive cycle


Here is the OBD2 emission system drive cycle test procedure.
Engine coolant temp must be below 70c (158f) before starting the engine for either the first or second trip
The fuel level should be less than 1/2 full
First trip:
Start engine, idle for at least 1.5 minutes
Drive 3 minutes, hold b/f schdl: 1.5-2.0 msec, selector lever "3rd" eng rpm 1,800-2,000 A/C switch:ON Hold the recommended b/f schdl range. Allow road speed to vary as necessary.
Drive at 55-65 mph for 1.5 min b/f schdl 2.0-3.2 msec, selector lever "5th" Engine rpm 2,200-3,000
IGN "off" for at least 10 seconds (not more than 5 min)
Dive at 50-60 mph for 3 minutes Selector lever "4th" keep engine speed above 3,000 rpm Allow speed to vary if necessary. Do not decelerate for more than 3 consecutive seconds. A/C switch ON.
Drive at a steady state cruise of 53-58mhp b/f schdl more than 1.8 msec selector lever "5th" eng rpm 2,400-2,600
Downshift to "4th" and decel more than 5 seconds without breaking, then idle for 1 minute.
Drive two minutes b/f schdl less than 2.0 msec Accelerate to 41 mph, decelerate to 34 mph, accelerate to 41mph. Do not completely release the accelerator. A/C switch off.
Idle 1 minute in park or neutral
Drive two minutes Steady state cruise at 31-44 mph. Selector lever "4th" A/C switch OFF. Hold the accelerator pedal as steady as possible. Allow speed to change if necessary.
End of first trip. Turn the key off the begin the second trip.
Second trip:
Start engine, idle for at least 1.5 minutes
Drive 3 minutes, hold b/f schdl: 1.5-2.0 msec, selector lever "3rd" eng rpm 1,800-2,000 A/C switch:ON Hold the recommended b/f schdl range. Allow road speed to vary as necessary.
Drive at 55-65 mph for 1.5 min b/f schdl 2.0-3.2 msec, selector lever "5th" Engine rpm 2,200-3,000
IGN "off" add four gallons of fuel
Dive at 50-60 mph for 3 minutes Selector lever "4th" keep engine speed above 3,000 rpm Allow speed to vary if necessary. Do not decelerate for more than 3 consecutive seconds. A/C switch ON.
Drive at a steady state cruise of 53-58mhp b/f schdl more than 1.8 msec selector lever "5th" eng rpm 2,400-2,600
Downshift to "4th" and decel more than 5 seconds without breaking, then idle for 1 minute.
Drive two minutes b/f schdl less than 2.0 msec Accelerate to 41 mph, decelerate to 34 mph, accelerate to 41mph. Do not completely release the accelerator. A/C switch off.
Idle 1 minute in park or neutral
Drive two minutes Steady state cruise at 31-44 mph. Selector lever "4th" A/C switch OFF. Hold the accelerator pedal as steady as possible. Allow speed to change if necessary. I especially like the part where they want you to add four gallons of fuel. Not three gallons, not five gallons, four gallons. Gotta love those Nissan engineers. ...and of course they state that if the trace is not followed exactly (i.e. you botch the acceleration/deceleration) you have to start all over again from scratch

Feb 09, 2012 | 1996 Nissan Pickup

2 Answers

Radio


You can drive to the dealer and have them help you enter the code since they are alway's connecting and disconnecting battery's, The instructions are in the manual and the codes might be written in the front or back page. If no codes were programed try 0000 and see if that works. IF the dealer wants to charge you a crazy amount, you can get your codes here on www.radio-code.com Good luck and hope this helps.

Jun 03, 2009 | 1993 Chevrolet Astro

1 Answer

1993 grand marquis while driving the head lights goes off and on


check your connections at the headlights especially if they are sealed beams with the three way connecter sometimes they will get corrosion, or dirt and not get the propper contact vibrations from driving will cause them to lose contact.

next check your headlight relay it could be going bad and not pulling the internal switchinside of it to close.

hope this helps.

Mar 21, 2009 | 1993 Mercury Grand Marquis

2 Answers

Need Code


Turn the ignition ON (The radio displays LOC) 2. Press and hold presets buttons 2 & 3 or 1 & 4 for approximately 10 seconds.
3. The radio display changes from LOC to a three-digit number. Write this number down.
4. Don’t take long, fifteen seconds max before the next step.
5. Press the AM/FM button
6. The radio display changes to another three-digit number. Write this number to the right of the first one.
7. You now have a six or four-digit number, the first three digits are from STEP 3 and the last three digits are from STEP 5
8 If you have a four digit number, it will show all four digits at the same time. Example 4523

do this and let me know the code and i will call gm and get your code in the morning

Aug 25, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...