Question about Saturn Vue

1 Answer

Timingchain diagram procedure for the number one piston at top dead center

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 978 Answers

If its a straight six or four cylinder if no six valve rocking then one is on top dead centre or four cylinder 4 rocking one is on t dead centre

Posted on Sep 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I put the distributor in It it is Pointing at number one


Was number one piston on top dead center of the compression stroke? Was the timing mark on the harmonic balancer at 0, when it was at top dead center of the compression stroke? Try again.

May 29, 2015 | Cars & Trucks

1 Answer

How to get number 1 cylinder top dead center when motor is not running on a gmc 4.3 1991


With truck off, you can turn the crankshaft nut from bottom of engine. To bring to top dead center. Remove #1 plug and insert a straw or similar into plug hole on top of piston. When the piston just starts to go back down from all the way up, that's top dead center, The number one cylinder in the 4.3 V-6 is the front wire on the driver-side of the engine. God-Bless!

Mar 03, 2015 | 1991 GMC C1500

1 Answer

While driving truck there was a popping noise, motor turned off . Distributor cap and rotor along with spark plugs and wires changed. Truck still won't start. 2003 dodge ram 1500 5.9 litre


5.9 aren't prone to this, But pull the distributor cap. Have someone crank the engine and watch to see if the rotor moves. Also put the number one piston on top dead center on the compression stroke (remove the spark plug to check compression side). See where the rotor sets compared to a diagram At top dead center.. Sounds like the chain broke (unlikely) or jumped.

Sep 08, 2014 | Dodge Ram 1500 Cars & Trucks

1 Answer

Timeing diagram


timing needs to be set at TDC. ( Top dead center)
need to take out your number one spark plug and manually rotate engine ( the way it turns when running)
when your piston is at top,
That's where your timing mark is to fire on the first cylender.
Good luck.........

Aug 02, 2014 | 1998 Ford Escort

1 Answer

How to set timing on mazda 2.3 disi DOHC engine


u need to bring piston number 1 to top dead center and then line up your timing marks and put chain on

Apr 06, 2014 | 2009 Mazda CX-7

1 Answer

Replacing distributer suburban 1500 m 1997


HOPE YOU DIDN\'T TAKE OUT THE OLD ONE YET !!!!!!!!!! YOU MIGHT WANT READ UP ON THIS BEFORE YOU DO. BUT THERE ARE PROCEDURES, DISTRIBUTOR MUST BE MARKED, @ BASE/ENGINE BLOCK, USE PAINT, ROTOR MUST BE FACING #1 SPARK PLUG, #1 PISTON NEEDS TO BE SET @ TOP-DEAD-CENTER, ON THE COMPRESSION STROKE, NOT EXHAUST STROKE, IF YOU REMOVE THE VALVE COVER DRIVERSIDE IF V8, YOU CAN SEE #1 ROCKER ARMS. WHEN ROTATING THE ENGINE, MANUALLY W/WRENCH, BFW, BIG-FU-KIN-WRENCH, BOTH ROCKER ARMS WILL BE EVEN & LOOSE, IF YOU REMOVE #1 SPARK PLUG, THE TOP OF THE PISTON WILL BE @ TOP OF ITS STROKE, ALSO, TIMING MARKS WILL BE INLINE @ CRANKSHAFT DAMPER. @ 0, TOP DEAD CENTER. WHEN THIS OCCURS, YOUR @ TOP DEAD CENTER . DO YOU UNDERSTAND ???????? BY REMOVING ALL SPARK PLUGS IT WILL BE EASYIER TO TURN THE CRANK. ONCE YOU ACHIEVE & SATISFY ALL THE ABOVE PROCEDURES YOU CAN SET IN YOUR DISTRIBUTOR, ROTOR FACING #1 SPARK PLUG TERMINAL, THAT YOU ALSO MARKED, INSERT THE NEW DISTRIBUTOR EXACTLY LIKE YOU TOOK IT OUT, REPEAT, EXACTLY..........................GOOD LUCK!!!

Mar 25, 2013 | Chevrolet Suburban 1500 Cars & Trucks

2 Answers

Is it top dead center or bottom


Top dead center and bottom dead center also known as ( TDC) and (BDC) Are two different positions of the piston while an engine is running. TDC is where the piston is as high as it can go in the cylinder and BDC is as low as the piston can go in the cylinder.

May 21, 2011 | Pontiac Grand Prix Cars & Trucks

2 Answers

WHERE IS NUMBER 1 PISTON ON A 1994 TOYOTA 4RUNNER V6 3.0 EFI. WANT TO MAKE TOP DEAD CENTER. SO AS TO MAKE SURE TIMING BELT IS IN PROPER PLACE.


Check this diagram location for 1994 Toyota 4 Runner 4WD 3.0 liter SOHC V-6 (3VZ-E)...

zjlimited_75.gif


Hope thos helps (remember to rate this answer).

Dec 27, 2010 | 1994 Toyota 4Runner

2 Answers

Need to resit cam timeng firing frm top dead center no1 wat is no 1 piston


heres a diagram of # 1 piston, also heres a diagram of the timing marks for the crank and cam gears,im not sure what your doing but good luck, hope this helps you.611d849.gif2617fdc.gif

Mar 31, 2010 | 1996 Subaru Legacy

3 Answers

Where does number 1 piston need to be..do u go off that or piston 8


#1 should be all the way up.This is called TDC(Top Dead Center)

Jun 18, 2009 | 1982 Ford Ltd

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...