Question about 2003 Saturn ION

1 Answer

Wiper arm are stopping in center of windsheild tried all positions of of the linkage underneath wiper motor need diagram of how linkage go

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 474 Answers

This usually means fan motor is b/o. It is supposed to stop with the wipers down. That happened to me and it was the motor

Posted on Sep 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiper lingage adjustment


pull the arms off the shafts and cycle the wiper motor to the stop position . Replace the arms and tension the nuts.

Mar 08, 2014 | 1998 Cadillac Catera

1 Answer

Wipers stuck up when shut off. i need a diagram of the motor and arms


common GM issue, faulty wiper motor. buy another and either get a repair manual or search for a video on youtube of someone replacing their GM wiper motor. you will have to remove the linkage, swap the motor, then reinstall the linkage. be extra careful to make sure the wiper switch is in OFF position before you begin and to note the OFF position on the linkage as you reinstall the motor.

Feb 01, 2011 | 2002 Chevrolet Monte Carlo

1 Answer

Ever since i replaced the wiper motor on 2003 chevy impala the wipers stop in up position instead of down position when stop- ped on delay position.is it something i did wrong when replac- ing the...


try this fix
remove wiper arms from where they connect on car
turn wiper moter on then off. turn ignition off
if wiper motor is good it should put spline in off position and now all you need to do is replace wiper arms in the correct position they would be in when wipers are turned off

Dec 14, 2010 | 2003 Chevrolet Impala

1 Answer

Put in a new wiper motor 1997 e39 528i bmw\it stops in the middle


Remove arm(s), put wiper motor in park,(shut off) then re-install arm at base of windshield where they were before,when shut off.(in park position.)

Sep 26, 2009 | 1997 BMW 318

2 Answers

How do I change the motot to the windsheild wipers?


most likely the relays inside your windshield wiper motor are starting to go. if your mechanically inclined you can probably go to your local junkyard and pull another one from the same car. i know they run about 75 new from most auto stores. to remove the old one you need to remove the dust cover underneath the windshiel wiper arms (easier with hood open). they should be small phillips screws or they are going to be push button clips (if they are clips just pry them out, you might need to replace them because some of them might break when removing). once you have the dust cover removed, disconnect the wiper arm linkage to the motor. then from inside the engine compartment remove the mounting bolts for the motor itself, don't forget the electrical connector. installation is the reverse of removal.

Jan 07, 2009 | Hyundai Motor 1998 Accent

4 Answers

Windshield wiper would not return to origi position


I had the same problem in my LW200. As the other poster indicated a new wiper motor will do the trick. This is an easy fix. Remove the wiper arms, pry up the plastic center cap and remove the nuts holding the arms down then pull them off. A soft prying nudge from underneath will help as they are splined shafts. Raise the hood, put a large deep well socket on over the splined shafts and remove the 2 large nuts holding the trim panel on. Pull up and off the long rubber which runs along the front of the trim panel, watch there is a sharp edge underneath. Now you can gently pull off the trim panel, remembering to lift it over the splined shafts. Mechanism is right there, remove 3 screws and unplug wiring. Take wiper motor off the linkage swap with a new one at advance auto, about 100 bucks, reinstall in reverse order. Note there is a stamping on the linkage telling you where the pivot arm should be for the rest or stopped position and if you ignore that your wipers will be out of whack. While you are in there you may want to change the cabin air filter as well.

Nov 18, 2008 | 2001 Saturn L-Series

9 Answers

97 nissan sentra windshield wiper linkage arm disconnected


Most likely you will have to replace the wiper linkage from the center pivot to the left or drivers-side wiper pivot. The plastic piece in the linkage gets brittle over time and breaks down. To save a hassle in the future, replace both linkages. It should be under $20.00 for parts.

Jul 13, 2008 | 1997 Nissan Sentra

Not finding what you are looking for?
2003 Saturn ION Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...