Question about Chevrolet 1500

1 Answer

I have the fuel pump ready to remove but I can't get the gas lines off. The connectors or so kind of pressure fitting. I can push them in and spin a little but that is it.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 51 Answers

Take a pair of pliers and squeez the pressure fittings there should be two prongs sticking out press those together with the pliers, you may need a flat head screw driver to push the compression clap off after you squeez the two prong together try wigglying and pulling it at the same time.

Posted on Sep 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How To Drain Fuel Tank On 2005 Jeep Liberty Gas Tank


here is the Cherokee page.
read chapter, 14, page 19 on..
shows all way there, and is not easy.
why do this.
is pressure low
pump dead
is there 12vdc to pump cranking, (no? then dont do this)

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

i have the KJ pages here. (line # messed up)
Two different procedures may be used to drain fuel
tank: through the fuel fill fitting on tank, or using a
scan tool.
The quickest draining procedure involves removing
the rubber fuel fill hose (7) (Fig. 25) from fuel tank
fitting.
As an alternative procedure, the electric fuel pump
may be activated allowing tank to be drained at fuel
rail connection. Refer to DRB scan tool for fuel pump
activation procedures. Before disconnecting fuel line
at fuel rail, release fuel pressure. Refer to the Fuel
System Pressure Release Procedure for procedures.
Attach end of special test hose tool number 6541,
6539, 6631 or 6923 at fuel rail disconnection (tool
number will depend on model and/or engine application).
Position opposite end of this hose tool to an
approved gasoline draining station. Activate fuel
pump and drain tank until empty.
If electric fuel pump is not operating, fuel must be
drained through fuel fill fitting at tank. Refer to following
procedures.
(1) Release fuel system pressure.
(2) Raise vehicle.
(3) If equipped, remove fuel tank skid plate.
(4) Thoroughly clean area around fuel fill fitting
(6) (Fig. 26) and rubber fuel fill hose (1) at side of
fuel tank. After cleaning, loosen fuel fill hose clamp
(2) at tank.
(5) Before removing rubber hose (1) (Fig. 26) from
fitting, note hose orientation while referring to marks
(3) and (4).
6) Disconnect rubber fuel fill hose at fuel tank fitting
(2) (Fig. 27). Using an approved gas holding
tank, drain fuel tank through this fitting.
Tank Removal
(1) If equipped, remove fuel tank skid plate and
tow hooks. Certain equipment packages will also
require removal of the trailer hitch. Refer to Tow
Hooks, Trailer Hitch or Skid Plate in 23, Body for
removal/installation procedures.
(2) Disconnect and separate fresh air tube (6) (Fig.
28) quick-connect fitting.
(3) Disconnect air tubes at front of NVLD pump
(9) (Fig. 28).
(4) Disconnect NVLD pump (9) (Fig. 28) electrical
connector.
(5) Disconnect fuel pump module electrical connector
jumper. This is located near front of fuel tank.
(6) Support tank with a hydraulic jack.
(7) Remove 4 fuel tank strap bolts (10) (Fig. 28) (2
at front of tank; 2 at rear of tank), and remove both
tank support straps.
(8) Carefully lower tank a few inches.
(9) Continue lowering tank while guiding remaining
hoses and lines through plastic isolator sleeve (3)
(Fig. 29).
(10) If fuel tank is to be replaced, remove NVLD
pump and fuel pump module from tank. Refer to
Fuel Pump Module Removal/Installation procedures.
end , tank out.

why not login to alldata.com and read
or buy the FSM,, and get all pages of chapter 14, end to end.

Oct 19, 2015 | 2005 Jeep Liberty

1 Answer

How do I syphon the gas from a 1999 plymouth grand voyager?


Forget trying to syphon via the filler cap as most now have anti-syphon built in. Try breaking into the fuel line before it enters the engine and let the fuel pump do the work. On my old car (a 2002 Fiat) the line was just a push-fit connection. I disconnected and fitted a hose over the line to a container. I turned on the ignition and the pump switched on and started filling the container. It did, however, need switching on and off a few times because I believe there is some kind of pressure switch within the system and the pump stopped once it realised the pressure to the fuel injection system was not building up.

Nov 02, 2014 | 1999 Plymouth Grand Voyager

1 Answer

Evap system


The FSM is clear on this. each hose and fitting must be air tight.
or the the car vents gas fumes full time, and the EVAP ECU tests
(monitor) make sure this all works.
you can just look at the left and right side above rear tires. and see
if your hands are small enough to fit here. Id bet not.
some mech, report, the tank can be tilted down at front (drained fuel)
and gain access.
keep in mind, you get fuel siphoning at any time. do not open the system, with fuel in the tank, and then drive to autozone,
i loosen the gas cap so that pressure can not build in tank.
expanding fuel can push fuel out , during a filter change. very
dangerous in a garage, and you gone.
it's just a vent hose, you can see, it and what needs to be done is really obvious. given you arms sides and lenght.
my fsm states, " TANK pull"

Removal & Installation

  1. Relieve the fuel system pressure and disconnect the negative battery cable.
  2. Remove the fuel filler cap from the fuel tank.
  3. Have a Class B fire extinguisher near the work area. Use a hand operated pump device to drain as much fuel through the fuel filler neck as possible.
  4. Use a siphon to remove the remainder of the fuel in the tank by connecting the siphon to the fuel pump outlet fitting.
    CAUTION Never drain or store fuel in an open container because there is the possibility of a fire or an explosion.
  5. Reinstall the fuel filler cap.
  6. Remove the rear seat cushion from vehicle (if so equipped).
  7. Disconnect the fuel pump motor connector and sending unit electrical connectors.
  8. Disconnect the wire harness grommet and harness through the vehicle floor pan.
  9. Raise and safely support the vehicle.
  10. Remove the fuel filler hose clamp from the filler neck assembly.
  11. Remove the fuel breather hose clamp from the filler neck assembly.
  12. Remove the fuel filter inlet hose clamp and hose from the filter.
    NOTE A small amount of fuel may be released after the fuel hose is disconnected. In order to reduce the chance of personal injury, cover the fitting to be disconnected with a shop towel.
  13. Remove the fuel vapor clamp and hose, and fuel return hose clamps and hose from the respective fuel lines.
  14. Using a suitable transaxle jack, support the fuel tank.
  15. Remove the fuel tank retaining bolts and lower the tank.
To install:
  1. Reconnect all fuel hoses, lines and the fuel breather hose to the fuel tank.
  2. Place the fuel tank in its proper space using the transaxle jack, Install the fuel tank retaining bolts.
  3. Remove the transaxle jack.
  4. Reconnect all fuel hoses, lines and the fuel breather hose to the fuel tank.
  5. Install the fuel breather hose and hose clamp to the filler neck assembly.
  6. Install the fuel vapor hose and hose clamps. Install the fuel return hose and hose clamp to the respective fuel lines.
  7. Install the fuel filter inlet hose and hose clamp to the filter.
  8. Lower the vehicle. Install the wire harness and grommet through the vehicle floor pan.
  9. Connect the fuel pump motor and the sending unit connectors.
  10. Install the rear seat cushion. Reconnect the negative battery cable.
"

Mar 26, 2013 | 2002 Suzuki Esteem

1 Answer

How to change fuel pump?


safely raise and support the back of the vehicle. The fuel pump will be on the passenger side of the fuel tank.

remove the fuel lines from the pump. Be careful as any residual pressure in the lines will spray out and get you. Wrap a rag around the connector before you remove it to reduce the spray.

Unbolt the passenger side fuel tank strap. You will need to do this to remove the wiring harness to the pump.

Remove the 6 bolts holding the pump to the fuel tank. An 8mm socket should work. If the tank is full gas will start coming out at this point. Have a drain pan ready to catch it.

Pull the pump out of the tank. This can be a bit of a rubix cube but the pump will come out without having to pull or drop the tank.

Please be careful! anytime there is fuel vapor or spilt fuel there is the chance for fire.

Use new clips in the fuel line fittings. There should be one black clip and one white clip. They only go into the fitting with the tab facing the line. If you put them in backwards the lines will pull off.

Sometimes they use a quick connect fitting that a release tool needs to be used to get the fittings off of the fuel pump. They can be purchased at any good auto parts store. There are two sizes and most parts stores will carry the tool that has both sizes in one tool.

Make sure you replace the fuel filter when replacing the pump.

Oct 20, 2010 | 2002 Ford Crown Victoria

2 Answers

How does one replace the fuel filter on a 1998 Buick century? What degree of difficulty is it for a non mechanic ( but has some experience w/ basic car maintenance)?


The fuel filter is under car by gas tank. Use ramps or jack up car and support it good.
Loosen gas cap to relieve any pressure in system.
Twist the connector 1/4 turn in either direction to loosen any debris. Squeeze the plastic tabs on the end of the connector and pull the connector apart. Repeat for the other connector.(some models might have a screw in connector on one side) you will need a couple of wrenches.
Remove filter mounting bolt, unhook the tab from the receptacle in the frame and remove filter. Installation is just reverse.
snap the connector back on and pull to make sure it connected. You will need a drip pan to catch the fuel when you dsconnect the lines and what's in the filter.

Sep 22, 2010 | 1998 Buick Century

1 Answer

WHERE IS FUEL FILTER? 1999 HRYSLER 300M


Fuel Filter Removal & Installation NOTE: A combination fuel filter and fuel pressure regulator is used on all gas powered engines. It is located on the top of the fuel pump module. It contains a diaphragm, calibrated springs and a fuel return valve. The internal fuel filter is also part of the assembly.
To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Release fuel pressure
  3. Remove or disconnect the following:
    • Fuel Tank refer
    • Fuel tank and remove the purge line and vent line.
    • Fuel line from pressure regulator. Fuel Pressure Regulator Locking Tab dod_intrpd_fuel_reg_lckng_tabs.gif

    • Pressure regulator by pushing the locking tab in from locking slot and turning pressure regulator to unlock it.
    • Pull regulator straight up.
To Install:
  1. Push regulator down and into place.
  2. Turn fuel pressure regulator to lock it in place. Make sure take the locking tab is in the locking slot.
  3. Install or connect the following:
    • Fuel line to regulator
    • Fuel pump electrical connector into hole in the body.
    • The purge and vent lines.
    • Tank into position and install tank straps.
    • The fuel filler tube and tighten the clamp.
    • The stabilizer bar and install bolts.
  4. Lower vehicle.
  5. Install or connect the following:
    • The fuel pump electrical connector that is in the rear seat.
    • The rear seat.
    • The battery cable.
  6. Fill fuel tank. Use the DRB scan tool to pressurize the fuel system. Check for leaks.
prev.gif next.gif

Jul 21, 2010 | 1999 Chrysler 300M

1 Answer

How do i replace the fuel filter on a 2000 Nissan Sentra


Fuel filter for SRDE20B15 engines (00-01) are in the tank mounted on top of the fuel pump inside the fuel assembly. Release fuel pressure by starting car and removing the fuel pump fuse, open fuel filler cap, remove rear seat, open fuel assembly cover by turning the screws clockwise, remove harness, remove fuel line quick connector carefully (if pressure was not relieved, gas will leak, make sure to release pressure completely), take out fuel assembly (watch out for fuel level sensor and temp sensor thingies). Pop top off the fuel assembly and pop fuel level sensor unit with screwdriver. Remove fuel pump harness connector, quick connectors. Pop top off completely, pop fuel filter+pump assembly out, remove fuel pump bracket on the bottom of it. Push fuel pump down from the top harness connector, Take out the rubber grommet (very important - car won't start) between fuel filter and fuel pump, put it into new fuel filter, and reverse all the steps to close it up.

Apr 23, 2010 | 2000 Nissan Sentra

2 Answers

1999 ford ranger fuel pump needs replaced.


Hello!

REMOVAL

WARNING:
  • DO NOT SMOKE OR CARRY LIGHTED TOBACCO OR OPEN FLAME OF ANY TYPE WHEN WORKING ON OR NEAR ANY FUEL-RELATED COMPONENT. HIGHLY FLAMMABLE MIXTURES ARE ALWAYS PRESENT AND MAY BE IGNITED, RESULTING IN POSSIBLE PERSONAL INJURY.
  • FUEL IN THE FUEL SYSTEM REMAINS UNDER HIGH PRESSURE EVEN WHEN THE ENGINE IS NOT RUNNING. BEFORE REPAIRING OR DISCONNECTING ANY OF THE FUEL LINES OR FUEL SYSTEM COMPONENTS, THE FUEL SYSTEM PRESSURE MUST BE RELIEVED TO PREVENT ACCIDENTAL SPRAYING OF FUEL, CAUSING PERSONAL INJURY OR A FIRE HAZARD.
  1. Disconnect the battery.
  2. Relieve the system pressure.
  3. Raise the vehicle.
  4. Drain the fuel tank.

cc999cb.gif
  1. Disconnect the fill pipe hoses.
    • Loosen fill pipe hose clamps.
    • Disconnect fill pipe hoses from the fuel tank.

f3fcce3.gif
  1. Remove the 4 bolts (2 each side) and remove the skid plate if equipped.
  2. Support the fuel tank.

918ba9a.gif
  1. Remove the bolts and pivot the fuel tank support straps away from the fuel tank.

e19f38e.gif
  1. Disconnect the fuel pump connector.
    • Lower the fuel tank slightly. Disconnect the fuel pump connector.


958d5a3.gif
Disconnect the fuel supply line push-connect fitting and the vapor tube fitting at the fuel pump


80378e1.gif
  1. Disconnect the vapor line fitting at the rear of the fuel tank.
  2. Lower the fuel tank.

62ccbfd.gif
To install, reverse the removal procedure


df22959.gif Special Tool(s)

REMOVAL

  1. Clean the area around the fuel pump mounting flange.



b28c7f0.gif
  1. Using the special tool, remove the fuel tank pump assembly locking retainer ring.
  2. Remove the fuel pump assembly. CAUTION: The fuel pump assembly must be removed and handled carefully to avoid damage to the float arm and filter.
  3. Remove and discard the fuel pump mounting gasket.
INSTALLATION
  1. Clean the fuel pump mounting flange and the fuel tank mounting surface.
  2. Apply a light coat of Premium Long Life Grease XG-1-C or -K or equivalent meeting Ford specification ESA-M1C75-B to the gasket to hold it in position during assembly. Install the fuel pump mounting gasket.

4976d12.gif
  1. Using the special tool, tighten the fuel pump assembly locking retainer ring.

Mar 02, 2010 | 1999 Ford Ranger SuperCab

1 Answer

How to change fuel pump on 2005 nissan sentra 1.8L


1. Release fuel pressure by removing the fuel pump fuse and spinning the engine over.
2. Disconnect the battery ground cable.
3. Open the fuel filler lid and remove the fuel filler cap at relieve the pressure in the fuel tank.
4. Remove the rear seat cushion.
5. Remove the inspection hole cover located under the rear seat cushion by rotating the attaching clips 90 degrees to line them up for removal.
6. Disconnect the fuel pump assembly electrical connector.
7. Disconnect the fuel feed hose quick connector. You will need to push in the winged tabs at the end of the fuel line. Be careful not to break it.
8. Remove the six fuel level sensor and fuel pump assembly retainer ring screws.
9. To remove, pull up the fuel pump assembly. Be careful not to damage the fuel level sensor. You will have to tilt the assembly to remove it completely.

Dec 19, 2009 | 2005 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...