Question about 2006 Hummer H3

Open Question

My hummer H3 2006 won't start and it's giving me RFA 1 on screen?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont start


New onstar module? What is RFA?

Apr 01, 2014 | 2003 Chevrolet Avalanche

2 Answers

Can I reprogram my keyless remote from my 1995 eldorado to my 1996 cadillac eldorado


AS programs can be altered I would have it checked out at a dealer service centre as they will need the keys and the vehicle to see if it can be done

Jan 11, 2014 | 1996 Cadillac Eldorado

1 Answer

My Hummer H2's trunk won't open.


That roomy gap could be an indication that the latch is misaligned and jammed.

Aug 12, 2017 | Hummer H2 Cars & Trucks

1 Answer

Mesage on center screen says RFA Battery low


Hello: The RFA stands for the Key Fob That you use to lock?unlock your doors. RFA stands for Remote Function Actuator.. Replace the battery. Go to Auto Zone and they should have the battery and probably not charge you to replace it.

Aug 23, 2011 | 2003 GMC Sierra 1500

1 Answer

How do I program a Cadillac 2004 Deville remote key fob?


came across this, maybe this will help out...this is for analog gauges....

With the ignition in the "RUN" position (engine does not necessarily need to be running, but it will work either way).
Press OFF and WARMER (or the OFF and PASSENGER WARMER buttons) on climate control panel simultaneously. Instrument Panel Cluster (IPC) will light all telltales, then go blank. System is now in DIAGNOSTIC MODE. After diagnostic mode cycles through and stops, press FAN DOWN button until "RFA?" is displayed, then press FAN UP. If "RFA DATA?" is displayed, press FAN DOWN. If "RFA OVERRIDE?" is displayed press FAN UP button.

If "RFA S00 NO OVERRIDE" is displayed, press FAN DOWN. If "RFA S01 PROGRAM FOB #1" is displayed, press FAN UP button.

IPC will show "0" on right side of Drivers Information Center (DIC) display. Press WARMER button on the climate control unit until "99" is displayed.

Press and hold TRUNK button on the transmitter. While holding TRUNK button, press LOCK button and hold both buttons for a total of 3 seconds. Locks will cycle when programming is complete. If transmitter is not programmed within 30 seconds after entering "99" on the display, system will default and you must begin at step #2 again.
To program second transmitter, press FAN DOWN button until "RF S02 PROGRAM FOB #2" is displayed, then press FAN UP. Repeat step #4.

To exit system, press AUTO, MODE UP, MODE DOWN, or RESET button.
__________________

Oct 30, 2010 | 2004 Cadillac Deville

7 Answers

What does RFA 1 battery low mean?


The battery in your keyless remote #1 for the vehicle is low and needs replacing.

May 24, 2010 | 2003 GMC Yukon

2 Answers

RFA battery low. What does this mean


Check you Key FOB for a low battery.

May 20, 2009 | 2003 GMC Sierra 2500HD

1 Answer

Programing a new remote


Use these instuctions if your Deville has an Analog Instrument Cluster
1. Press OFF and WARM buttons on Climate Control Panel (CCP) simultaneously.
(Instrument Panel Cluster (IPC) will light all telltales, then go blank) System is now in diagnostic mode.
Press PASSENGER COOLER button until “RFA” is displayed, then press FAN UP.

If “RFA DATA” is displayed, press FAN DOWN.
If “RFA OVERRIDE” is displayed, press FAN UP.
2. If “RFA 500 NO OVERRIDE” is displayed, press FAN DOWN.
If “RFA 501 PROGRAM FOB #1” is displayed, Press FAN UP.
3. IPC will show “0” on right side of Driver Information Center (DIC) display.
Press warmer button on climate control unit until “99” is displayed.
4. Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
step 2.

5. To program a second remote, press FAN DOWN button until “RFA 502 PROGRAM FOB #2” is displayed, then press
FAN UP. Repeat step 4.

To exit system, press AUTO, MODE UP, MODE DOWN, or RESET.




Use these instructions if your DeVille has a Digital Instrument Cluster
1. Press OFF and WARM buttons on Climate Control Center (CCC) simultaneously. Instrument Panel Cluster (IPC) will
light all telltales, go blank then enter DIAGNOSTIC
MODE. Press FAN DOW button to scroll through system until
“RFA” is displayed, then press FAN UP button. Press FAN DOWN button until “RFA OVERRIDE” is displayed, then
press FAN UP button. When “NO OVRD RF 500” is displayed, then press FAN UP button.

2. When “PGM FOBL 501” is displayed, press WARM button and “99” will be displayed in left upper corner of IPC just
below odometer. System is now ready to program remote.

3. Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
step 2.)

4. To program second remote, pres FAN UP button until “PGM FOB2 502” is displayed, then follow steps 2 and 3 to
program second remote.

To exit system, press RECIRC or RESET buttons.

Disclaimer

Apr 25, 2009 | 1998 Cadillac DeVille

Not finding what you are looking for?
2006 Hummer H3 Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...