Question about 2000 Dodge Neon

2 Answers

Motor Mounts How do I remove the motor mounts to raise the engine to make a repair and put it back without hurting me or the vehicle

Posted by on

2 Answers

Buy a real car

Posted on Jun 01, 2008


  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Engine rise and fall on one side when shifting to reverse from park on a 1994 Dodge Caravan 3.0 six cylinder

Posted on May 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace motor mounts on 2003 hyundai sonata


You really need the car on a lift or tall jack stands to do this. You will need a full set of hand tools, a good hydraulic floor jack, a set of Jack stands (AKA Safety Stands) and a 1.5 Ton bottle jack. Raise the front of the car as high as possible and unbolt the old mounts from the engine and engine cradle, then Carefully using the bottle jack (put a piece of wood on the plunger of the jack to avoid damage to the oil pan) raise the engine off the mounts and remove them, and reverse install new mounts, time about 2-3 hours to do the repair.

Oct 12, 2016 | Hyundai Motor 2003 Sonata

1 Answer

How to remove oil pan without pulling motor on 89 mitsubishi mightymax


You must disconnect the engine from the motor mounts and exhaust and remove anything that will interfere with raising it off the mounts as high as possible, once it is off the mounts and raised the pan can be removed. I read this at a owners site from a guy who has done the job, he said it is a real pain in the rear but doable.

Sep 01, 2016 | 1989 Mitsubishi Mighty Max

3 Answers

How do i know which motor mount needs replacement


With car in drive/reverse and foot hard on brake if the engine moves when gas pedal is depressed and quickly released in both D&R, then that mount/mounts is defective...

Engine mount should be replaced if:

1) The hard rubber surface is covered with heat check cracks.

2) The rubber is separated from the metal plate of the engine mount.

3) The rubber is split through the center of the engine mount



The transmission case will crack or break if either engine mounts or transmission rear mount is broken...Here is a GM Service bulletin addressing the issue:

#02-07-30-024B



The transmission mount (see drawing) test:

>Raise and support the vehicle

>Raise the transmission/transaxle in order to remove the weight from the transmission/transaxle mount and create slight tension in the rubber.

Replace trans. mount if anyone of the three conditions listed above exist
...saailer





know-motor-mount-needs-replacement-veetken1ee5qxi1ah1dwzeam-2-0.png

Jan 02, 2015 | 2004 Chevrolet Impala

1 Answer

How do you tell if your motor mounts are bad


Park vehicle on level surface, set the parking brake and chock the rear wheels. Disconnect negative battery cable and raise vehicle up and support it with jack stands. If equipped with air suspension disconnect electrical power to air suspension.Position jack underneath of engine oil pan, use piece of 2 x 4 or block of wood and raise engine slightly to take the weight of engine from motor mount. Inspect the engine mounts for crack or rubber deterioration and separation.

Mar 15, 2014 | Ford Windstar Cars & Trucks

1 Answer

How do i disconeect the motor mounts i need to disconnect motor mounts so i can raise the motor and remove th oil pan


The motor mounts have a hinge bolt that goes through the upper engine hard bracket and the engine mount rubber section, it goes from from to rear in line with the engine, remove the nuts and take the load off the mount with a floor jack under the pan (use a block softwood to avoid denting the pan), once the nut and load is off slide the long bolt out and raise the engine.

Jul 02, 2012 | 1999 Ford Ranger SuperCab

2 Answers

How do you remove a oil pan from a 1984 z28 camero


Drain the oil completely, remove all the bolts and drop the pan. On 84 I don't believe you have to remove the tranny. Just remove the bolts.

You can go to autozone.com and signup for a free account. Then login to the account, choose your vehicle year, make, model, and engine size. Finally click on view repair manual. Now you have a free repair manual for your vehicle.

Apr 28, 2011 | Chevrolet Camaro Cars & Trucks

2 Answers

When i back up or go forwad i heard a sound from all the ingenie like it is movning?


Hi,
Without seeing, it's hard to come up with a solution, but raise the hood and have someone (or yourself) look at the engine motor mounts when the car is put in forward or reverse. You may have a broken motor mount.
Hope this helps... Good luck!

Jul 09, 2010 | 2003 Ford Focus

1 Answer

HELP!!! Trying to Remove oil pan from 1985 Cheve


wow! that really sucks.... first if you drop the cross member you should be able to get at with ease other wise if you dont wanna screw with that unbolt the engine mounts and raise the front of the engine up BUT THIS TIME WATCH THE DISTRIBUTOR.... dont get near the fire wall... get me informed of other problems. and there aint no good way of taking the motor mounts out just take a wrench and put it on the bottom nut and take an impact wrench to the bolt

Feb 27, 2009 | 1985 Chevrolet S-10

3 Answers

Motor mount


The engine mounts are located about the middle of the block on the side of the engine. The only other mount is located under transmission.

Jun 09, 2008 | 1998 Jeep Wrangler

Not finding what you are looking for?
2000 Dodge Neon Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...