Question about 1992 Toyota 4Runner

4 Answers

Clucth pedel the clutch pedel will not release stays down on floor board

Posted by on

Ad

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

There are 3 reasons for the pedal to remain stuck down in a Hydraulic system:
a: The spring that lifts the pedal back to its position is broken, this is under the Dash.
b: The springs on the pressure plate have damaged.
c: The hydraulic cylinder piston gets stuck when pressed completely down this is located in the engine compartment on the fire wall.

Posted on Oct 17, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hey man, i had a similar problem
you should look under at the clutch bracket to see if that broke
then check above the same bracket to see if the upper mount broke

idk
hope this helps

Posted on Oct 17, 2008

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 359 Answers

What type is it cable or fluid.
If its cable it has possibly snapped if its fluid check your level and maybe slave sylinder on the side of the gearbox

Posted on May 25, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Check your Clutch fluid level

Posted on May 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car has difficulty going in gear even if pedel is fully down


The clutch is not fully disengaging. Adjust the clutch cable to obtain a 1/2 inch of free play at the top of pedal stroke. If clutch adjustment is not correct, damage to synchronizers or clutch release bearing will occur. Your clutch should begin to engage about an inch off the floor when releasing the clutch pedal.

May 25, 2017 | Cars & Trucks

2 Answers

I was parked on the side of the road in my ford ranger ute for about 3 to 4 minutes with the clutch pedal to the floor i was on the phone and then i could smell the clutch burning. I took my foot off the...


The clutch might be a hydraulic system. When it's leaking oil the pedal sticks to the floor and has to be pulled back manually. Because it's designed to be fail safe, it still works but only for some time till all the oil has leaked out.

The burning smell might be clutch oil dripping on the exhaust - meaning the seal on the clutch servo is leaking oil.

There are repairkits for clutch servo's - usually it's suggested to replace the cylinder seal on the clutch pedal also.

Jul 01, 2011 | Ford Ranger Cars & Trucks

1 Answer

Vw sharan I changed clucth and flywheel but some times clucth padel stays down and first gear hard to change.


sounds like the pivot for the clutch release arm has broken or the the release arm has come off the pivot.

Jan 11, 2011 | Volkswagen Tiguan Cars & Trucks

3 Answers

The clutch peddle will not come up it stays on the floor


Check on the upper part of the pedel to see if the clip that connects the pedel to the clutch master cylinder has poped off If the clutch pedel is on the floor this is a likely sulition and relitively easy repair you just reattach the clip

Nov 06, 2010 | 1992 Honda Accord

2 Answers

Clutch pedel stuck on floor


The clutch master has blown out

Jan 19, 2010 | 1990 Ford F250

1 Answer

Clutch does not release


did you check your pedal freeplay check your adjustment you need to have not more thant 1 inch freeplay on the clutch pedal what it does is when you did not adjusted right it cannot release your release bearing also check your linkage aite..

Feb 23, 2009 | 2005 Ford Fusion

1 Answer

I have an rx7 series 6 twin turbo manual transmission. When I pump the clutch pedal while engine is running the pedal eventually ends up flat on the floor and doesnt return unless physically pulling up...


Asuming its a "normal clucth", im no "RotaExp". ill say release-bearing or springs=New clucth house.
But "pumping" realy just sounds like a very BAD idea...;)

Sep 27, 2008 | Mazda RX-7 Cars & Trucks

Not finding what you are looking for?
1992 Toyota 4Runner Logo

275 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...