Question about 1999 Isuzu Rodeo

3 Answers

Isuzu rodeo 1999 3.2L

I have a part that goes with the throw out bearing it fits onto it and it is round and has teeth on it half the teeth are broken off and it fits into the trans noone here in this hicktown seems to know what it is calle dso therefore i cannot fix it please help me

Posted by on

  • CNIDAVE Jun 20, 2008

    DOES THE THROW OUT BEARING LOCK AROUND THE PRESSURE PLATE?



×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Isuzu Master
  • 1,224 Answers

Need more of a discription but right off my head a couple things

if its big its the starter plate if its small its the starter gear

drive shaft
the other is called a spline connecting drive shaft to throw out bearing you need to send out whole drive shaft to get replaced cause these require balancing they connect by u-joint
if they dont know what a drive shaft components are then you will need specialist to do whole drive shaft correctly

isuzu rodeo 1999 3.2L - e0d8d63.jpg

Posted on May 28, 2008

  • Christophe Thompson
    Christophe Thompson May 28, 2008

    if you need a place and most these places are out of state give me hollar and i will give you top of the line drive shaft manufacture name

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do you open a hatch on a 99 isuzu rodeo when the latch is dislodged?

Posted on Nov 07, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My 99 rodeo runs good but every once in a while it dose not start the starter is good the bat is good the clutch is good where should i look next

Posted on Oct 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Camber ajustment on isuzu rodeo 2003


if this is an independent front end the the camber can be adjusted by shims or eccentric washers on the lower arm
If it is a full axle the there are off set bearing cups available that a wheel alignment shop can fit when checking the camber. These bearing caps are available from places like Pedders and other accredited suspension shops.

Mar 08, 2015 | 2003 Isuzu Rodeo

2 Answers

97 rodeo clutch repair- throw out bearing swingout arm


Hi,

Sorry but no quick/dirty trick to my knowledge. The bellhousing has to be removed/pulled out and the release bearing slide in place.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jun 04, 2008 | 1997 Isuzu Rodeo

1 Answer

On a 1999 Isuzu Rodeo 3.2 V6 DOHC If you put all timing marks together on engine and then put timing belt mark all together on the engine and rotate two rounds with crankshaft does all the marks come


Just the engine. The marks on the belt are to make sure the teeth are in the right place when replacing. It might come back in place on 4 turns of the crankshaft. I have never checked to see if the belt marks came back. But always check the timing marks themselves.

Hope this helps.

Nov 10, 2014 | 1999 Isuzu Rodeo

1 Answer

Throw out barring fork doesnot allignment with clutch slave fork too short


Did it pop out of position or what? Or was this after you replaced the clutch or what?

Well on clutch forks ive seen. There is a rounded stud sticking out and goes into a rounded
spot on the that the fork, and the makes the fork pivot.

And theres a spring that snaps the throwout bearing onto the fork. Could either be that
the spring broke, or the fork is not aligned on the rounded stud and has slipped down.

I think the spring broke and made the fork drop down, because the spring holds the bearing
onto the fork and the fork could not have dropped down without the spring either breaking
on popping off. There is usually a rubber boot that covers the place where the fork goes
into the transmission. Pull the boot off and look through the holes where the boot goes.
If somrhing has come off or broken you will be able to tell.

Aug 12, 2011 | 1987 Dodge D150

1 Answer

Can you let me know what is the gear ratio for a 1995 isuzu rodeo. My rear differential is broken


Should be a metal tab bolted to rear inspection cover of differential displaying gear ratio or count the number of teeth on pinion (small gear connected to drive shaft) Divide number into the number of teeth on ring gear

Mar 22, 2011 | 1995 Isuzu Rodeo

2 Answers

I replaced the wheel bearings on the drivers side of my 2001 isuzu rodeo and i am trying to get the snap ring back in place but the spindle will not come out far enough. i am about 1/16" shy from the clip...


Your wheel bearing isn't seated all the way to it's stop and need to be pressed in further. Usually you'll know when it hits the ledge, it won't do anything even if an elephant was standing on it.

Jun 10, 2010 | 1998 Isuzu Rodeo

1 Answer

I just install an different engine in a 1999 3.2L Rodeo. the fork for the throw out bearing is hitting the pressure plate when the clutch in depress any help?


Sorry to tell you this-but you do not have the throw out bearing fork properly installed on throwout bearing. There is a spring clip on the fork that has to fit inside of throwout bearing's "groove"-I bet you the spring clip is on the BACKSIDE of throwout bearing! You will have to pull transmission back away from the engine to gain access to fix this. I do not envy the chore ahead of you-sorry!

Apr 08, 2010 | 1999 Isuzu Rodeo

1 Answer

Need some help with replacing the gear box and transfer on my 94 isuzu rodeo 2.8lt turbo desiel iv gt the gear box and trans just need to know what else i need to put them in... any help would be just...


You might want to consider the clutch and pressure plate, throw out bearing, and pilot bearing,rear main seal, check your U-joints and CV joints

Mar 09, 2010 | 1994 Isuzu Rodeo

2 Answers

2005 rodeo 4wd turbo diesel


possibly the throw out bearing....which is part of the clutch assembly

Oct 09, 2008 | 2004 Isuzu Rodeo

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

1,575 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...