Question about 1998 Honda Prelude

1 Answer

How do you put on the hood emblem? There is no hole under the hood to put the ruber stopper to keep the emblem in.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 48 Answers

If you are reinstalling it onto a new replacement hood you may have to drill the hole especially if it's not an "OME" some times when you save money on the parts you have to do some of the labor, that's how they save on the cost. Also some of the emblems are held in place with 2 sided tape that is not what you can buy in the store. You might go by an auto body shop and ask for help, most good shop will give information to you for free, if you don't make a pest of yourself. off peak hours are better.

Posted on Sep 29, 2010

Testimonial: "Thank you very much! "

  • sonictronic Sep 30, 2010

    Even if it is an aftermarket hood it should still be "OEM" style. Most hoods come with the holes pre-stamped. If it has the holes in the outer facing panel all you need are two "tubular clips" as Honda calls them. Part number 91512-SR3-004. you can order these at your Honda dealer. They just push into the hole where the emblem goes from the outside. The back of the emblem should have two "studs" protruding, if not it will need to be replaced and should come with new clips. It is part number 75701-SM4-900. Should cost less than $20 even if you need the entire emblem.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Is a fuse box on a yukon xl under the hood

Under the hood and dash and possibly passenger and driver side under dash fuse blocks.

Jul 25, 2015 | Cars & Trucks

1 Answer

How to remove hood emblem

underneath the hood were the emblem is there should be a spring lock or fasteners you can undo

Apr 21, 2014 | 2007 Mercedes-Benz CLS500

2 Answers

The brake lights wont shut off when i turn off the car. i have a pack of rubber stopper to replace the missing stopper which i found crumbled up on the floor but i dont know where the hole is to put the...

weird but try this. at the top of you brake pedal you see a switch that the brake pedal touches when in the unpressed position see if that stopper you are talking about mounts on the pedal arm .

Apr 25, 2010 | Hyundai Motor 1999 Tiburon

3 Answers

How to replace 2004 bmw z4 hood emblem

if it's regular emblem , then it has two plastic pins on the sides (Left and right , very tight fit), it's almost impossible to pull emblem out without braken it.
hood has two plastic clips ,were those pins go.

Apr 18, 2010 | 2004 BMW Z4

4 Answers

Water on passenger floorboard.

HI. This will occur if the heater core has ruptured(leaking). This will allow for the transfer of coolant onto the passenger side floor. Replacing the core will solve this issue.

Oct 22, 2009 | 2003 Chevrolet Impala

1 Answer

Got to be intermittent and then quit altogether

you might have a bad vacume valve
eithor it fails under presure or it has a bad presure sensor could be a bad vac line thet moves when you are at highway speed opening and closing depending ho fast you go and how hot it is under the hood

ruber lines het hot ruber lines flex
asa it cools then it re seats it self

Jul 09, 2009 | 2004 Mazda Tribute

1 Answer

Tiny pin hole in auto fuel line. What kit can I

most of the time it means yor fuel line needs replace . if its ruber i would bye some 6mm 0r 8mm copper pipe to siut yor car and cut it in to yor hose with two clamps to grip it rub some sand papper on each end to give it a good grip put you way need to put a bit of spit just to get it in the ruber pipe .a good inch pushed in will do. hope this helps

May 06, 2009 | 2008 Lincoln Town Car

1 Answer

How do you get wires from under the hood to in the cab chevy s10

there should be ruber plugs under cab on both sides at back of cab.

Jan 06, 2009 | 2001 Chevrolet Tahoe

1 Answer

Installation of mercedes hood emblem e class 1998 E430

Look at the new one real close and you will see the locking device that has to be pulled down and turned. It is locked in place so the ormanent will fit through the hole. Just remove whats left of the old one. Push new one through the hole and hold in in place from the top while turning locking piece under hood  with pliers 1/4 turn. The locking piece is spring loaded so you will have to pull down and turn. That's it.

Dec 30, 2008 | 1998 Mercedes-Benz E-Class

1 Answer

Hood emblem installation

Just put the replacement hood ornament in the hole and use a pair of pliers to pull down and turn the lock 1/4 turn clockwise. It is spring loaded and if you look real close at the ornament you will see what piece to pull down and turn. Right now it is locked in its shipping spot.

Jul 30, 2008 | 1989 Mercedes-Benz 300-Class

Not finding what you are looking for?
1998 Honda Prelude Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides