Question about 1994 Mazda 323

Open Question

Removal of starter motor on 94 Lantis - 1994 Mazda 323

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Interchsnge yesrs or other make,/models for Starter in 1994 Toyota Corolla


If it's the 1.6 motor then 94 to 96 corolla take that starter only. But if it's a 1.8 motor then 94 to 97 take that starter and also geo prizm 94 to 97 takes that starter

Aug 15, 2014 | 1994 Toyota Corolla

1 Answer

The engine turns over but not starting the cambelt is good. iv tried puting plugs in the hose but stil wont work help! (v6 manual lantis 94)


what do you mean putting plugs in the hose?
are you getting spark?
have you replaced the cam timing belt?
if so did you line all timing marks up?

Jan 13, 2011 | Mazda 323 Cars & Trucks

1 Answer

How to put the Starter in a Eagle Talon 1991.


from autozone.com


REMOVAL & INSTALLATION
See Figures 5, 6, 7, 8, 9 and 10

  1. Disconnect the negative, then the positive battery cables from the battery.
  2. For 1990-94 vehicles, remove the battery and battery tray from the engine compartment.
  3. For 1990-94 vehicles, detach the speedometer cable connector from the transaxle.
  4. For 1995-98 2.0L turbo engines, remove the air hose.
  5. For 1995-98 2.4L engines, remove the air cleaner and air intake hose.
  6. If equipped with 1.8L engine, remove the bracket on the lower side if the intake manifold.
  7. Detach the starter motor electrical connections.
6f8c23b.gif

Fig. Fig. 5: Exploded view of the starter motor and related components-1990-94 vehicles, others similar


458b681.gif

Fig. Fig. 6: Unfasten the BAT terminal connector from the starter motor


05a1691.gif

Fig. Fig. 7: Unplug the starter motor electrical connector

  1. Unfasten the starter motor mounting bolts, then remove the starter from the vehicle.
d0adab9.gif

Fig. Fig. 8: Unfasten the starter mounting bolts
d00c214.gif

Fig. Fig. 9: Remove all of the starter mounting bolts ...
c92a470.gif

Fig. Fig. 10: ... then remove the starter motor from the vehicle
To install:

  1. Clean both surfaces of starter motor flange and rear plate. Install the starter motor onto the engine and secure with the retainer bolts. Tighten the retainers to the specifications shown in the accompanying figure.
  2. Attach the electrical harness connector(s) to the starter.
  3. If removed, install the intake manifold stay and tighten the retainers to 18 ft. lbs. (25 Nm).
  4. For 1995-98 2.4L engines, install the air cleaner and air intake hose.
  5. For 1995-98 2.0L turbo engines, install the air hose.
  6. For 1990-94 vehicles, attach the speedometer cable to the transaxle. Install the battery tray and battery.
  7. Connect the positive, then the negative battery cables.
Operate the starter to assure proper operation.

Oct 29, 2010 | 1991 Eagle Talon

1 Answer

Tools needed to remove starter on 94 dodge spirit 3.0 liter V6


Regular socket wrench set, wrench set, screwdriver, etc.: REMOVAL & INSTALLATION Fig. 1: These three attaching bolts hold the starter motor to the engine/transaxle assembly - all models 86722051.gif
  1. Disconnect the negative (-) battery cable. Raise and safely support the front of the vehicle on jackstands. Remove the engine undercovers, if so equipped.
  2. Remove the 3 bolts attaching the starter to the engine/transaxle. CAUTION
    Be careful when removing the starter motor mounting bolts, the motor can be quite heavy. Personal injury could result if the starter motor falls from its mounting position.
  3. Remove the heat shield and its clamp, if so equipped.
  4. Remove the two electrical wire connector terminal nuts and remove the wiring connector from the starter.
  5. Remove the starter from the vehicle. To install:
  6. Clean all wire terminals of dirt, grease or corrosion.
  7. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 80 inch lbs. (9 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  8. Install the heat shield if one was removed.
  9. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm) for all vehicles except Premier and Monaco. Tighten the attaching bolts to 20 ft. lbs. (27 Nm) for Premier and Monaco.
  10. Install any undercovers which were removed from the vehicle.
  11. Lower the vehicle.
  12. Connect the negative (-) battery cable. Fig. 2: After disconnecting the starter's electrical wiring, remove the 3 mounting bolts . . . 86722p15.jpg
    Fig. 3: . . . then the starter motor can be lowered from the underside of the vehicle 86722p16.jpg
prev.gif next.gif

Sep 24, 2010 | 1991 Dodge Spirit

1 Answer

Need a manual to change the starter on a, 1994 Nissan, Quest mini van + 6 cylinders


http://groups.yahoo.com/group/villagerquest/

Section 03-06: Starting System 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Starter Motor stv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: WHEN SERVICING THE STARTER MOTOR OR PERFORMING OTHER UNDERHOOD WORK IN THE VICINITY OF THE STARTER MOTOR, BE AWARE THAT THE HEAVY GAUGE BATTERY INPUT LEAD AT THE STARTER SOLENOID IS "ELECTRICALLY HOT" AT ALL TIMES. A PROTECTIVE BOOT IS PROVIDED OVER THIS TERMINAL ON ALL VEHICLE LINES AND MUST BE REPLACED AFTER SERVICING. BE SURE TO DISCONNECT THE BATTERY GROUND CABLE BEFORE SERVICING THE STARTER MOTOR.
Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the engine air cleaner (ACL) (9600). Refer to Section 03-12 for the removal and installation procedure.
  1. Slide back the protective boot and remove the nut securing the battery positive cable on the B-terminal of the starter solenoid (11390).
  1. Remove the battery positive cable from the B-terminal.
  1. Disconnect the S-terminal electrical connector.
  1. Remove the two starter motor bolts.
  1. Remove the starter motor (11002) from the vehicle.

Apr 27, 2010 | 1994 Nissan Quest

1 Answer

Need directions to change a starter on a 94 cadillac deville. 4.9 liter engine.How difficult with a floor jack in the driveway


Depending on your mechanical ability, it can be considered fairly easy. If you're working in your driveway,PLEASE be sure to block the wheels so you don't get crushed under the car.

Gather the necessary tools needed such as wrenches, sockets, screwdriver and pliers.
Place the vehicle on ramps or jack up the front and support with jack stands. It is very important to block the rear wheels to keep the car stationary during this procedure. Never work under a vehicle not supported properly
Make sure ignition is OFF and the remove the negative (ground) battery cable from the battery.
Note the location of all wires before removal to make for easier connection.
Remove the large starter cable going to the battery at the starter location.
Remove any other wires attached to the solenoid.
Remove the starter attaching bolts (usually there are two or three).
Remove any supporting brackets that holds the starter.
Drop the starter down away from the car. On some cars you may have to turn the wheels to one side, remove the idler arm, remove or loosen transmission oil cooler lines, exhaust pipes, or ground straps to give you enough clearance to get the starter motor away from the car.
Install the new starter in the reverse order of removal.
Reconnect battery cables and other wires to solenoid.
Place old starter in the new starter box for proper core return.

Sep 20, 2009 | 1994 Cadillac DeVille

1 Answer

2004 chrysler pt cruiser starter motor removal


You may sneak it out with small fingers with out pulling out the starter.

If starter removal is required,Just unhook the battery cables,Remove the 2 bolts holding the starter on.


Please rate this a fixya

Feb 08, 2009 | 2004 Chrysler PT Cruiser

2 Answers

Starter motor


Is there any sound when the key is turned? The solenoid may be stuck, and a light tap with a hammer may free it up. The starter is located on the engine block.

This is what you are looking for....
http://i8.ebayimg.com/02/i/001/22/0b/39e7_1.JPG


REMOVAL & INSTALLATION
STARTER MOTOR
Removal & Installation (2.0L)

CAUTION:When battery is disconnected, vehicle computer and memory systems may lose memory data. Driveability problems may exist until computer systems have completed a relearn cycle. See COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION before disconnecting battery. Before testing starter, ensure transmission is in Park or Neutral.

Disconnect negative battery cable. Remove air cleaner. Remove upper starter mounting bolts. Raise and support vehicle. Disconnect starter solenoid wire connections. Remove starter motor lower mounting bolt. Remove starter motor. To install, reverse removal procedure. Ensure negative battery cable is installed with starter mounting bolt. Tighten bolts to specification. See TORQUE SPECIFICATIONS table.

Removal & Installation (2.5L)

Disconnect negative battery cable. Remove air cleaner and air cleaner bracket. Disconnect starter solenoid wire connections. Remove starter support bracket. On manual transmission equipped models, remove shift cable bracket and disconnect cable. On all models, remove fuel supply line from support bracket. Remove starter bolts. Remove starter. To install, reverse removal procedure. Tighten bolts to specification.

Jan 01, 2009 | 2000 Ford Contour

1 Answer

Starter removal 94 explorer


u have to undo the motor mounts put a board under ur oil pan lift ur motor i think its three bolts to the starter

Dec 30, 2008 | 1995 Ford Explorer

1 Answer

My starter


'94 through '97 should share the same starter.

Jun 14, 2008 | 1997 Honda Civic

Not finding what you are looking for?
1994 Mazda 323 Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...