Question about 1999 Hyundai Accent
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
CHANGING ENGINE OIL Be careful not to burn yourself, as the engine oil is hot. 1. Run the engine until it reaches normal operating temperature. 2. Stop the engine. 3. Remove the oil filler cap (on rocker cover) and the drain plug (on the oil pan). Drain the engine oil. 4. Re-install and tighten the drain plug to the specified torque. 5. Fill new engine oil through the oil filler. a. Cover the generator with a shop towel before pouring the engine oil to ensure that if oil spills, it will not drop on the generator. b. Use a funnel to pour in the engine oil. 6. Install the oil filler cap. 7. Start and run the engine. 8. Stop the engine and then check the oil level. Add oil if necessary.
Posted on May 24, 2008
SOURCE: 2002 Hyundai Accent Problem
first thing i need to know is did the timing belt break?
second is are you sure you aligned the timing marks and after the belt tensioner was tight you rechecked to make sure the timing stayed where you had it.
next step would be a compression check to if a valve was bent whenchanging the belt
i have seen this happen and this engine is an interferance engine.
Posted on Sep 28, 2008
Check the coolant level, do this with a cold engine. Or if you have recently used it. let it cool down for about 25 minutes before removing the radiator cap. if it is low, refill with coolant. If it does not, check your thermostat. Or better yet replace your thermostat. Be sure to get the right one . the same degrees as your old one. Just ask the teller to give you one for your engine size and car Model.And year.See where the radiator cap is. Then drain some coolant to where it will not spill from the radiator cap. Remove the hose nearest the radiator cap and you will get to the thermostat housing. Remove the housing and note how the thermostat is placed. Take of the thermostat housing and the old thermostat. Clean the housing and around the hole where the thermostat goes of any deposits. Get some grease and cover the new gasket with grease on the housing to hold it in place. replace the New thermostat and make sure it is flush with the engine and the housing. If it is off , you could break the housing upon tightening the housing.replace the hose and refill with coolant slowly to eliminate any air spaces.. Also check the coolant reservoir and fill it to the indicator line. Restart the car and chek for any leaks. Then check the heater after the engine heats up. If that does not do the job it could be the temperature sensor or the heater core.The heater core will take more time to check and clean or replace.
Posted on Nov 26, 2008
A car can overheat for a lot of reasons.First make sure this is the problem by checking the radiator hose or water level. Open the radiator cap when the car is cold, crank it, and then watch the water level. If it drops when the car warms up this is not the problem.
The tools you will need will depend on what you have to take off to get to it. If you can access the thermostat you should only need a ratchet or wrench to remove it and something to scrape off old gasket with.
Location:The thermostat should be inside the thermostat housing on the motor. Follow your top radiator hose to the place where it goes into the motor. There should be a sort of dome shaped housing there with probably a bolt on either side of it.The thermostat is inside that.
This is a reasonably easy job, but shouldn't be done carelessly. It's also kind of messy.
When the car is cold remove the bolts from the housing with a ratchet. Lots of coolant and water will drain out. But the thermostat will be visible.Pay attention to which side of the thermostat is up.It should just lift up. Remove all the old gasket from around the area and clean it up well. Replace the thermostat and gasket then the bolts. Be very careful not to over tighten the bolts or the housing will be ruined.
Posted on Apr 22, 2009
Tips for a great answer:
Jan 05, 2016 | Hyundai Cars & Trucks
Jan 10, 2014 | 1996 Hyundai Accent
Aug 08, 2011 | 2000 Hyundai Accent
Nov 22, 2010 | 2008 Hyundai Accent
Jan 26, 2010 | 2001 Hyundai Accent
Dec 30, 2009 | 2005 Hyundai Accent
Nov 19, 2009 | 2001 Hyundai Accent
Nov 17, 2009 | 1999 Hyundai Accent
Nov 24, 2008 | 2003 Hyundai Accent
264 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: