Question about GMC W3500

1 Answer

Gmc w4500 with 5.2 L after driving loses throttle response and kicks code p1094 fuel rail pressure low at idle or deceleration

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 170 Answers

Follow this link. Hope it helps. Good Luck.
http://www.duramaxforum.com/forum/04-5-05-lly-duramax-powertrain/106-trouble-codes.html

Posted on Sep 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What parts do you recommend for a fault on my Hyundai Tucson which has developed faults?


uh oh, 1186 and 0087 are both related... fuel pump or the filter or both! either case the filter is now located inside the fuel tank

P1186 Hyundai Fuel Pressure Too Low


P0087 Fuel Rail System Pressure Too Low

"Potential causes of a P0087 trouble code may include: Weak fuel pump, clogged filter or screen, restricted fuel supply line Faulty fuel pump driver module Faulty fuel pressure sensor"


How to Change the Fuel Filter on Hyundai Tucson eHow

according to eHow, you can access the filter relatively easily. (although the pic is an illustration of something not really related to this ~ why they showing a fuel petcock that's not even on your car?)

P2112 Throttle Actuator Control System Stuck Closed

"Possible causes:
- Throttle Body Plate Binding
- Faulty Throttle Actuator
- Throttle Actuator harness is open or shorted
- Throttle Actuator circuit poor electrical connection"

older models we had the gas pedal attached to a cable to move the butterfly valve on the throttle body. Now it's this newer drive-by-wire stuff... remove air intake hose and check / clean / move the throttle body valve by hand first to see if it's binding or not

then, go from there on testing the actuator and tps

Apr 17, 2015 | 2006 Hyundai Tucson

1 Answer

94 z28 chevy camaro fuel pressure check valve location and is there any other names for this item I recently installed a stock replacement fuel pump in my camaro I run 35psi which is low at idle unplug the...


do you mean the pressure relief valve, this is located normally on the low pressure or return side of your fuel rail, this is designed to maintain fuel pressure in your fuel rail constant, e.g. steady running requires steady pressure, acceleration requires increased pressure controled by engine vacuum, if it was on the supply line you can not regulate the pressure supplied to the injecters. stopped engine requires no pressure so the pump gets turned off with the ignitionf

Nov 27, 2013 | Cars & Trucks

2 Answers

CAN A IDLE VELVE CONTROLLER MAKE YOUR CAR CUTTING OUT WHILE DRIVING


It is called an idle air control valve (IAC), and it will cause stalling at idle or while decelerating to a stop, but engine stall while driving at steady speeds, no that will not be the fault of the valve.

May 17, 2012 | 2005 Volkswagen Microbus

1 Answer

P1191, p1193, p0300, p0301, p0305 Starts and idles fine but after aceeleration bogs down and idles very low/stalls sometimes. Replaced plugs, wires, air filter, fuel filter and Accelerator Position...


codes say misfirings--but I thinc its fuel rail pressure from 1st 2 codes--call napa and confirm--dont replace anymore things till u know issue--fuel pressure regulator or pump shud be tested--also idle air motor may not be opening-they wear

Sep 20, 2011 | 2002 Hyundai XG350

1 Answer

I have a 1996 gmc yukon 4x4 have flood problems I have put in new fuel pump has good fuel pressure changed coolant sensors changed throttle body changed computer plugs wires distributor cap and button coil...


Possibly a busted fuel pressure regulator diaphragm. The regulator is mounted to the end of the fuel rail.
With the engine idling, pull the vacuum line off the regulator port. If gas comes out of the port, replace the regulator.

0996b43f80219b2e-sulc2cgngkoxge0rocse0fez-1-0.gif

Aug 06, 2017 | 1996 GMC Sierra

1 Answer

My 2001 GMC Sonoma is idling rough, starts hard but when accelerates sounds good. I have replaced the fuel pump, fuel filter, and now all the plugs and wires, but still rough?


Check for vacumn leaks ! Idle air compensator? clean throttle valve oppenings and air port opening,do you have check engine lite on,check EGR valve? Dirty fuel injectors ,bad pressure regulator?Check fuel pressure at fuel rail,at idle !

Sep 06, 2010 | 2001 GMC Sonoma Extended Cab

1 Answer

Replaced fuel pump and filter now car idles but no throttle. car has a low fuel pressur code could this be a fuel pressure regulator?


COULD BE THE FUEL RAIL PRESSURE SENSOR OR YOU HAVE THE WRONG FUEL PUMP FOR THE VECHICLE.PCM COULD BE OUT OF CALIBRATION.TURN OFF RADIO FIRST THEN DISCONNECT NEGATIVE BATTERY CABLE FOR A MINUTE THEN HOOK BACK UP NEGATIVE BATTERY CABLE.THEN CRANK CAR UP LET IT GET OPERATING TEMP BEFORE THROTTLING IT.GIVE PCM TIME TO RECOGNIZE THE NEW FUEL PUMP.

Jun 08, 2010 | 2000 Mercury Mystique

2 Answers

Idles too low, won't keep running. Idles about 400RPM and will stay there if you feather down the throttle. Can't seem to find Vacuum leak. Sounds like slight air sucking sound toward back of firewall but...


You need to replace your idle air control valve. It is located on the throttle body with 2 screws holding it in. Should take about 15 minutes to replace and doesn't cost too much either. That will get you taken care of. Good luck. Thanks for rating my response and for using FixYa!

Jun 30, 2009 | 1996 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

946 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...