Question about 1997 Lincoln Town Car

2 Answers

Turn signals and hazard lights do not blink or show up on the instrument panel.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Replace your turn signal switch

Posted on Sep 28, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 40 Answers

Probably a bad relay. Easy fix... you just have to find the relay and replace it. Relays are very cheap.

Posted on Sep 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the signal light relay that makes signal lights flash located on 2000 ols intrigue 3.5 liter


Important: The hazard warning switch includes the turn signal and hazard warning flashers.
Removal Procedure
Remove the center air deflector. Refer to Instrument Panel Center Air Outlet Deflector Replacement .
Squeeze the retainer on the backside of hazard warning and cruise control switch.
Pull the hazard warning and cruise control switch from the retainer in the instrument panel.
Disconnect the electrical connectors from the hazard warning and cruise control switch.
Remove the hazard warning and cruise control switch from instrument panel.
Remove the hazard warning and cruise control switch bezel from the instrument panel trim pad by using a small flat-bladed tool to the release retainers.
Remove the radio. Refer to Radio Replacement in Entertainment.
Reach through the radio opening and push the retainers up towards the roof of the vehicle. When the retainers release, slide the instrument panel (I/P) center air outlet deflector out of the I/P opening
Remove the air outlet deflector
Remove the instrument panel accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement in Instrument Panel, Gauges, and Console.
Remove the bolts from the radio.
Pull the radio toward you.
Remove the front floor console trim plate. Refer to Front Floor Console Trim Plate Replacement .
Pull the instrument panel (IP) accessory trim plate away from the IP trim pad.
Disconnect the IP harness seat heater leads, if equipped.
Remove the seat heater switches from the IP accessory trim plate, if equipped.
Remove the IP accessory trim plate.

Nov 09, 2016 | Cars & Trucks

1 Answer

Turn signal relay 2008 jeep location


There is no relay , controlled by integrated power module . Electronics !

Feb 12, 2016 | 2008 Jeep Grand Cherokee Laredo

1 Answer

I have an 02 kia sportage. my signal lights come on but dont blink outside. no lights for the signal lights come on on the dash at all. also, no hazard lights.


If the 15A HAZARD fuse in the passenger compartment fuse box is OK, power is getting to the hazard function of the flasher unit. Pressing the hzard switch should cause the hazard lights to flash. HOWEVER, there is an electronic time and warning indication system module connected to to the hazard switch lead and that may be affecting things. If the 10A TURN fuse is OK, power is applied to the turn switch (with the engine in START or RUN) and you state you can select a right or left turn. HOWEVER, the RED/WHT and RED/BLU outputs from the flasher unit connect directly to the front and rear turn lamps and the instrument cluster turn indicators so you are not getting any flasher output. Again, that electronic time & warning indication system module could be affecting things

Oct 26, 2012 | Cars & Trucks

1 Answer

Turn signals were working...but blinking fast. now they don't work at all...replaced fuse in side panel near door and still nothing. Everything else works..headlights, wipers, hazards..what gives?


you have a separate flasher for the turn signals.this is what your problem sounds like.if all your lights are working including the signal indicator on the dash then it will be the signal flasher.if you turn on the hazard flashers and locate it under the dash, this will show you what the turn signal flasher will look like.then you will have to look for the flasher unit on the fuse panel that looks like the hazard flasher.replace the turn signal flasher and you will have your signal flashers again

Mar 08, 2011 | 1996 Dodge Ram 1500 Club Cab

1 Answer

I have Ford Explorer model 1998 but its indicator lights are not working meanwhile the hazzard lights are working


Your turn signal flasher is separate from the hazard flasher. Replace the turn flasher.

Both the turn signal flasher and the hazard warning flasher are mounted on the fuse panel on the truck. To gain access to the fuse panel, remove the cover from the lower edge of the instrument panel below the steering column. First remove the two fasteners from the lower edge of the cover. Then pull the cover downward until the spring clips disengage from the instrument panel.
The turn signal flasher unit is mounted on the front of the fuse panel, and the hazard warning flasher is mounted on the rear of the fuse panel.

Oct 02, 2010 | 1998 Ford Explorer

1 Answer

Blinker do not work it lights up but do not blink


The Flasher Relay is defective. Replace it. Know that your car has 2 Relays. One for the Turn Signals and one for the Hazard Lights. The Turn Signal flasher relay is located on the driver's side, under dash, behind instrument panel, mounted on passenger side of steering column. The Hazard Relay is located on the driver's side, under dash, driver's side of steering column, mounted in lower corner of fuse block. Make sure you replace the correct relay.

May 06, 2010 | 1995 Buick LeSabre

3 Answers

My 2003 chevy impala turn signals won't blink. the lights come on but won't blink. I have checked the fuse. it looked fine.


Hi,

Your problem is your blinker or flasher, it is located under dash, behind the instrument panel right above the steering column. Cost is no more than $10.

If helpful, click below, GOOD LUCK

Apr 15, 2010 | 2003 Chevrolet Impala

1 Answer

My 1999 ford exploler singnal lights are not working


I suggest check the FLASHERS for turn sugnal and hazard lights.

Both the turn signal flasher and the hazard warning flasher are mounted on the fuse panel on the truck. To gain access to the fuse panel, remove the cover from the lower edge of the instrument panel below the steering column. First remove the two fasteners from the lower edge of the cover. Then pull the cover downward until the spring clips disengage from the instrument panel.

The turn signal flasher unit is mounted on the front of the fuse panel, and the hazard warning flasher is mounted on the rear of the fuse panel.

Hope help with this; rmemeber rated this post.

Apr 09, 2010 | 1999 Ford Explorer

1 Answer

The turn on lights does not flash


Check out this recall below:
Bulletin No.: 04098A

SPECIAL POLICY
Subject:
04098 - Special Policy Adjustment - Turn Signal/Hazard Warning Flashers 

Condition
Some customers of 1999-2002 Chevrolet Malibu, Oldsmobile Alero, Pontiac Grand Am, and 1999 Oldsmobile Cutlass may have turn signal/hazard flashers that become inoperative.

Special Policy Adjustment
This special policy covers the condition described above for a period of 10 years or 150,000 miles (240,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. The repairs will be made at no charge to the customer.

Good luck and hope this helps:
HAZARD WARNING SWITCH REPLACEMENT - ON VEHICLE 
REMOVAL PROCEDURE 

Remove the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent. 
Remove the instrument panel cluster. 
Remove the hazard warning switch bezel from the instrument panel using a small-flat bladed tool to release the retainers.
Remove the left side bolt from the hazard warning switch through the instrument panel cluster pocket Remove the right side and center lower bolts from the hazard warning switch through the center air louver deflector pocket.
Reposition the hazard warning switch from the instrument panel to access the electrical connector. 
Disconnect the electrical connectors from the hazard warning switch. 
Remove the hazard warning switch from instrument panel. 

INSTALLATION PROCEDURE
Connect the electrical connectors to the hazard warning switch.
Position the hazard warning switch to the mounting points in the instrument panel. NOTE: Refer to Fastener Notice in Service Precautions.
Install the left side bolt to the hazard warning switch through the instrument panel cluster pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) . 
Install the right side and center lower bolts to the hazard warning switch through the center air louver deflector pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) . 
Install the hazard warning switch bezel to the instrument panel pressing into place until fully seated. Install the instrument panel cluster. 
Install the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent.

May 24, 2009 | 2000 Oldsmobile Alero

1 Answer

1991 Maxima Turn Signals


the flasher unit controls both hazards and indication you will need to remove the shroud around the steering wheel and follow the wires coming off the indicator stalk down until you find the problem there should be some majour plugs on the stearing collum check thaat these are conected and work from there

Nov 30, 2008 | 1991 Nissan Maxima

Not finding what you are looking for?
1997 Lincoln Town Car Logo

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

fordexpert

Level 3 Expert

5516 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...