Question about 1988 Chevrolet Camaro

2 Answers

1988 Chevy Camaro Iroc Z

Where is the coolant fan switch located?

Posted by on

  • jimlightfoot Jul 23, 2008

    is the connector up by the fans?. the wire that actually plugs into the pass side of block.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

The engine fan switch is located in the right side cylinder head between the spark plugs. There are two different sizes that you might find installed, 5/16 or 9/16 inch threads.

Posted on Sep 02, 2009

Below your rt fan should see underneath the car looking at the bottom of the radiator been a long time since i was arond the i roc but im pretty sure thats where it is

Posted on Jun 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the horn relay located on a 1988 camaro?


I believe it is plugged into interior fuse box.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
https://ca.answers.yahoo.com/question/index?qid=20080504172413AA78RKW
Fuse box diagram for 1988 Camaro Iroc
1988 camaro fuse box location Google Search

Mar 19, 2016 | Cars & Trucks

Tip

How To Replace Ignition Coil 82-92 Chevy Camaro Iroc-Z Pontiac Trans Am Part 2...


How To Install Replace Ignition Coil 82-92 Chevy Camaro Iroc-Z Pontiac Trans Am Part 2 1AAuto.com<utube src="jMtq0HqGtk0">

on Jul 28, 2011 | Chevrolet Camaro Cars & Trucks

Tip

How To Replace Ignition Coil 82-92 Chevy Camaro Iroc-Z Pontiac Trans Am Part 1...


How To Install Replace Ignition Coil 82-92 Chevy Camaro Iroc-Z Pontiac Trans Am Part 1 1AAuto.com<br /><br /><utube src="hiczZ2JugAg"><br />

on Jul 28, 2011 | Chevrolet Camaro Cars & Trucks

1 Answer

How do i replace the rear axel bearings on a 1988 Chevrolet IROC Z28 Camaro


Put car in neutral, remove wheels, calipers and rotors, diff. cover. rotate carrier until you see wrist pin retaining bolt, remove bolt and slide out the wrist pin out of carrier. Next push axle inward to remove inner axle "C" retainer washer then slide axle out of tube. Then pry off axle seal and with slide hammer w/attachment remove axle bearing.

Feb 23, 2014 | 1988 Chevrolet Camaro

1 Answer

I have a 1988 camaro iroc with the fuel injected 305, my radiator cooling fan doesnt work and i just replaced the fan motor. Could it be a bad relay or bad ecm unit??


Well, yes and no.
Yes the relay or the computer could be faulty.
But the computer is not going to ground the relay until the engine temp reaches about 225 degrees.
Since the thermostat opens at 195 degrees running at 200 is normal.

Sep 30, 2012 | 1988 Chevrolet Camaro

2 Answers

1988 camaro iroc z 350 tune port injected. need to reset timing on the computer. jodie


To set the ignition timing you will need to disconnect the electronic timing control. It is usually a dark brown and black wire located on the passenger side foot well where the carpet meets the firewall. Once the wire is disconnected, loosen the distributor and set the timing with a timing light. If you have an automatic transmission, I think the timing is 6deg BTDC. Tighten the distributor down and connect the ETC wire.

Mar 12, 2011 | 1988 Chevrolet Camaro

1 Answer

Where is the location of the temp sending unit in a 1988 camaro iroc z


On the thermostat housing. Please rate me on this answer.

Jun 11, 2010 | 1989 Chevrolet Camaro

1 Answer

Heating problem


look for a large allen head plug on the thermostat housing if it is not present start the car cold with radiator cap off let the car run for at least ten minutes top off coolant and repeat.

Jul 02, 2009 | 1988 Chevrolet Camaro

1 Answer

Temperature guage doesnt work


the temp switch for the fan is not what you are wanting to change you need a temp sending unit which is usually in the block or in the head on the small block chevys most of the time it is in the drivers side of the block just below the head it is a little round disk with one wire coming out of it

May 18, 2009 | 1988 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

411 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...