Question about 2007 Toyota Camry

Open Question

2007 Camry Rubbing or grinding noise coming from left rear

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 104 Answers

SOURCE: Recently purchased a 2007 Camry, 2.4 Liter 4 cycle 2AZ-FE engine. My older 2001 camry had the oil filter located on the rear front (left side of the engine. Where is the oil filter located on my new c

Your filter is visable by looking under the car. its near the exhaust pipe again, but toward the front of the car. tucked near the plastic air shield.

Posted on Apr 29, 2009

  • 375 Answers

SOURCE: Grinding noise in the left

grinding on front wheel is caused by 2 things. a bad or loose wheel bearing,or worn out brakes, have them both checked
You might also want to check the level of fluid in the power steering reservoir - low or lack of fluid will also cause a noise (although more of a whining than a grinding).

Posted on Jul 29, 2008

chuck943
  • 783 Answers

SOURCE: Rubbing or grinding noise coming from Driver side rear tire/wheel

Yes the rear differential could be the cause if you have a limited slip rear axle. The clutches could be binding in the rear axle.This would be noticeable especially on turns and accelerating.

Posted on Apr 08, 2009

alicantecoli
  • 22156 Answers

SOURCE: When reversing my 2007 camry LE V6, I hear a loud

easy but you have to screw the piston in as its pushed in

Posted on Apr 19, 2010

  • 1 Answer

SOURCE: Front end rubbing or grinding noise but goes away

It could be a number of things, but a common problem with this car is rusty pins in the front end.  This is louder when turning.  There was a bulletin issued about it.

Posted on Jun 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a metal grinding noise when turning left only.


Replace the right side wheel bearing. But before you replace it. Listen to see if the noise is coming from the front or back. If you can't tell, Put some one in the back seat. Front bearings usually make noise. rear bearings, the noise can come and go.

Jun 26, 2015 | 2011 Jeep Patriot Latitude

1 Answer

Have rubbing noise when turning to the left on 2007 impala


Rear wheels have the voice of the metal friction surface of brake pads no handle, friction, friction over a period of time or a voice, went to mechanic processing, very simple!auto diagnostic tool.

Apr 12, 2013 | 2007 Chevrolet Impala

1 Answer

I'm having trouble with my brakes for a 1993 cutlass ciera s and lately I been hearing a rubbing and grinding noise coming from my rear brakes could anyone tell me what kind of problem this is ?


My first question would be have you taken the drums off and looked at the brake shoes yet ?
You won't know whats going on until you do.
It could be worn out shoes, or a broken spring rubbing the drum, or any number of things.

Oct 07, 2012 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Changed the rear rotors and brake pads and there is a grinding noise


Here is what I have found out. I have an 2008 Toyota Tundra 5.7 4x4, and I changed the rear brakes and rotors. No noise prior to service. After installing new rotors, I started getting a metal scraping noise. After $300.00 in diagnostics, I found that the new rotors are rubbing the against the brake shield. The inner lip of the rotor needs to be machined down to avoid this rubbing. See toyota tundra forum.com for pics.

Sep 10, 2012 | 2007 Toyota Tundra

1 Answer

2005 Ford Explorer is making a grinding noise


I had some issues with my 2005 explorer left rear. It was making a creepy old door sound at low speeds and then a high pitched whisel at high speeds. That turned out to be a broken wheel bearing and had it replaced. Note each wheel has two wheel bearings. After that a new noise developed that sounded like metal scraping/ grinding metal. It end up being the brake dust cover got bent when they replaced the bearing and it was rubbing something, the fix for that was bending it so it didn't rub. I hope this helps.

Sep 03, 2012 | 2005 Ford Explorer

1 Answer

2003 camry with 200,000 miles has rubbing noise not the brakes wondering if a cv joint or u joint problem


If you have a rubbing noise on the BRAKES then its most likely the pads worn out and touching the metal backing plate ,other wise it could be the wheel bearing worn or coming loose but the CV Joint if worn will make a clanking noise when turned on full lock either Left or Right.
So jack it up at the front and check the wheel bearings and turn the wheel to see if the noise is there as it will be a metal to metal noise ,but if pads are good then it will just be a soft rubbing noise.

Mar 22, 2011 | 2003 Toyota Camry

1 Answer

Recently replaced the original equipment front brake pads on a 1997 Toyota Camry V-6 with ceramic brake pads. Also replaced the front brake rotors. Used disc brake quiet/lube at time of installation. I am...


You did not mention working on the rear brakes, so I must assume that the rear brakes are still original equipment. Perhaps the grinding noise is coming from the rear.

Dec 16, 2010 | 1997 Toyota Camry

1 Answer

Left rear tire locks going forward but not in reverse


There is probably parts of the bearing that are rubbing against each other and jamming, lift the rear and move the wheel in and out (like shaking), also spin the wheel and listen for grinding noise, if it moves or makes irregular noise, your bearing needs to be replaced, if everything is tight than check your brake shoe pads, a dislodged piece may be jamming between the shoe and the drum(it happened to me before!).

Dec 14, 2010 | 1995 Toyota Camry

2 Answers

Rubbing or grinding noise coming from Driver side rear tire/wheel


I had the same problem that based on interner research is common for Fords trcuks/suvs. The common problem fro rear humming "rubbing"sound might be the rear wheel bearings/seal. These will need to be replaced as it will progressivly get worse and the noise louder and eventually the bearings can sieze. I would hesitate to take to a ford dealer if I were you as it can run $500-900. Take to mechanic that knows how to replace wheel bearings and seals. My mechanic replaced them for about $150. and the bearing and seals are around $40. A good way to test this is to raise the wheel were you can freely spin by hand...if does not spin or there is a lot of friction then it might be the wheel bearings.
Good Luck

Apr 08, 2009 | 2002 Ford Explorer

Not finding what you are looking for?
2007 Toyota Camry Logo

Related Topics:

486 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...