Question about 2007 Chevrolet Equinox LS New Cars

1 Answer

2007 chevy equinox codes p0700 &p0705. van goes into limp mode what is the problem?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Chevrolet Master
  • 76,109 Answers

P0700 Transmission Control System Malfunction, this comes on anytime a problem is sensed in the transmission
P0705 Transmission Range Sensor Circuit malfunction(PRNDL Input)
this means that the circuit that signals the transmission control module when u slect a gear (Drive reverse etc.) has a problem, this can be the range selector switch or the wiring connector or the control module, in order to pin down which part is causing the fault code the Chevy dealer must hook up a scan tool called a "Tech II" and read the transmission data as the different gear requests are made.

Posted on Sep 28, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2003 chyrsler 300m it went in limp mode codes p0700. P0340 p0344 p0430 p0888 came up cleared the codes and now it knocks.

clearing codes wont correct the problem and limp mode is designed to protect motor and transmission - p0700 is a transmission problem
P0700 Transmission Control System Malfunction p0340 is camshaft position sensor malfunction p0344 is also a camshaft position sensor circuit problem
P0344 Camshaft Position Sensor Circuit Intermittent your p430 is a cat converter problem and p0888 is transmission relay problem these reasons are limp mode the knock can be fuel not burning correctly or a lower engine knock can mean you damaged a piston

Nov 08, 2016 | Cars & Trucks

1 Answer

What are the probable causes of DTCs P0700 and P0765?

P0700 Transmission Control System Malfunction
P0765 Shift Solenoid D Malfunction
Clear fault codes and see if it comes back, if so,check wiring and plug for bad connection.

Sep 05, 2015 | 2007 Chrysler Sebring 2.4

1 Answer

Toyota yaris in limp mode with p0705/stability control light illuminated

EOBD II Error Code: P0705
Fault Location:
Multi-Function Transmission Range Switch - Malfunction (PRNDL Input) - Implausible Signal
Possible Cause:
Wiring/Connectors from/to Multi-Function Switch faulty.
Multi-Function Switch faulty.
Engine control module (ECM)/Powertrain control module (PCM)/Transmission control module.

Possible Solutions:
Check Wiring/Connectors from/to Multi-Function Switch.
Check Multi-Function Switch.
Check Measuring Value Blocks.

Apr 04, 2014 | Toyota Yaris Cars & Trucks

1 Answer

Limp mode/ check engine/ slip indicator/

You got the code

Go to the internet (Google)

Type: 2007 Toyota Yaris OBD PO705

Apr 04, 2014 | 2007 Toyota Yaris

1 Answer

2001 mitsubishi galant 2.4l p0135, p0705, p0715, p0720. Stuck in limp mode.

either fit a manual gearbox or change the control computer for the autobox,no work then do what i did and buy a old van and do kerbside mechanics better than nothing , i know when its raining and cold but at least you will earn a living and buy your spares from a autofactor and not a corner shop

Nov 20, 2013 | 2001 Mitsubishi Galant

1 Answer


P0700 - Transmission Control System Malfunction
This code is normally accompanied by another more specific code

Jun 02, 2011 | 2007 Chevrolet Equinox LS New Cars

1 Answer

Po705 code goes to limp mode start off in low gear & shift to drive car goes fine no issue. arrow still blinks thanks.

#p0705 the on board computer is not receiving any input from the Transmission Range sensor.Check wire harness and plugin at sensor for any damage or maybe it just came unpluged.If no damage could be found and it was pluged in propperly, then replace the sensor. Good Luck and have a good XMASS.

Dec 13, 2010 | 1994 Volvo 960

1 Answer

Hi ! I have a 2006 Chevy Equinox, I lose power to trans untill the truck barely wants to move after 2bks or so. p0700 / p0705 are the codes that have come up. We replaced the tcm (p0700). p0705 comes up...

Since this vehicle does have a possible reprogramming issue, before I spent any money on parts, let them hook their scanner(in this case it going to be the tech 2 with downloadable info from a mainframe to reprogram) and see if there are any other under lying codes or info. What this means is that they have the ability to read and interpret live data to pin point the issue. the code may be merely a reference point. There may also be a TSB regarding this issue. Start at the dealer, then work on replacement of parts. Always start with information first. Sometimes we are suprised by what we find. Let me know what they say and if you need anything else.

Aug 25, 2010 | Chevrolet Equinox Cars & Trucks

Not finding what you are looking for?
2007 Chevrolet Equinox LS New Cars Logo

Related Topics:

929 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides