Question about 1988 Chevrolet S-10

1 Answer

1989 s-10 pickup that needs an front end alignment and i cant afford to have it done so need to do it solo. can anyone help me on how to do this ?

Posted by on

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,565 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1978 Chevy pickup wheel alignment specs


That needs to be done on a machine and all the components of the front end checked for wear, also tweets to the specs may be needed to attain the desired results of a straight steering vehicle.

Aug 03, 2016 | Cars & Trucks

2 Answers

How to do a front end alignment to a 1989 toyota pickup?


The suspension components need to be checked for excessive wear on the front also the steering track rod ends for play
Jack up on axle stands and try to wobble the wheel for play

Jun 01, 2016 | 1989 Toyota Pickup SR5

1 Answer

Front end alignment


Get the four wheel alignment if you heave never had it done. Be aware that on the rear the adjuster bolts may jammed with rust. On the front, the ball joints, rod ends and strut bolts need to be on good condition.

Jan 19, 2014 | Subaru Impreza Cars & Trucks

1 Answer

I have a 2002 dodge ram 1500 crew cab two wheel drive pickup. The front tires have been wearing on the insidefor a while. I have replaced the upper and lower ball joints , lower control arms ,and bal


Strange.
Has anyone checked the front end alignment on a rack ?
Usually when the tires wear on the inside edges the camber is off and the tires are running on the inside edge more than the outside.
Or the front suspension is too low or heavy.

Jan 29, 2013 | Cars & Trucks

2 Answers

What can be done was told ther is no adjustments in front end of my car for alignment


all cars has to be align at a long period of time if you getting quick tire wear, the mechanic told you a story, only reason a vechicle cant aligned if front end been or side vechicle been in a car wreck or if you have severe worn suspension components it would be hard to adjust the camber or caster wheel alignment.go to another garage that do front end alignment.

Sep 09, 2012 | 1995 Lincoln Continental

1 Answer

I just had my daughters 2002 searing serviced in the area she goes to school. I had new tires and a front end alignment done for a little over 500.00 all done October 6, and now, maybe 1500 miles later...


yes definably should been taken care of before the alignment was done
u can' t get a accurate alignment done with loose parts up front (ball joints get loose before they break)
and under most circumstances ball joints don't totally fail in a 2 month period of time

Now if your daughter drives on a lot of rough roads or hits a lot of pot holes and ball joint was dry (not greased in long time) (alignment shop should at least greased front end parts if possible some factory and cheap aftermarket ball joints are sealed and u cant grease them) There a slight chance ball joint could failed that soon but i highly doubt it

Now should u go back to shop ?? call them and explian to them what happened and see if they will warranty there work if they will more than likely day u brought in your car they where busy and behind and it just got over looked
if they wont warranty there work i would go some where else they did bad job first time and wouldnt want them doing same again

Far as cost goes that a hard one to tell u cause shops labor rates greatly across the country and even from shop to shop in same towns
for cost i would make a couple calls to few shops and get a ball park figure for your area

Dec 27, 2010 | 2002 Chrysler Sebring

4 Answers

Steering wheel out of centre position when wheels are in straight ahead position


You need an alignment. Did this happen all of a sudden? if so something may be bent.

Nov 24, 2009 | 1998 Saab 900

2 Answers

Steering wheel turn to right, 1995 aerostar-extended


Something is wrong with the front end. Bring it in for a front end alignment (that could be all it needs) and have them check for problems with front end suspension components. There may be something that is worn out ( such as ball joints, or tie rod ends) that is causing the uneven tire wear. There may also be a problem from hitting a large pot hole, or curb, which bent something causing this. Tell the shop to NOT align the front end if they find that some components need to be replaced, as when something is replaced, you should have the front end aligned, and you don't want to have it done twice.

Apr 05, 2009 | 1995 Ford Aerostar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...