Question about 1995 Pontiac Grand Am

1 Answer

Where is the oil filter and oil pan? - 1995 Pontiac Grand Am

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

The oil filter lookes like a bean can (slightly thicker)on the side of the engine block.and the oil pan is also called the sump,its on the bottom of the engine (you get to it from under the car)and the plug is normally on the bottom most part of the sump to allow it to drain all the oil from it.....some cars you have to take off the splash guard under the engine to get to the underside of the engine.

Posted on Sep 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing oil pan gasket 1998 chevy silverado 305 cu.in.


REMOVAL PROCEDURE
  1. Remove the oil level indicator tube.
  2. Raise the vehicle.
  3. Remove the engine oil and the engine oil filter.
  4. Remove the oil filter adapter.
  5. Remove the starter.
  6. Remove the flywheel inspection cover.
  7. Remove the engine mount through bolts.
  8. Raise and support the engine.




  1. Remove the oil pan nuts and bolts. Note the location of any studs to assist reassembly.
  2. Remove the engine oil pan and the gasket.
  3. Clean all sealing surfaces. Refer to Oil Pan Clean and Inspect under Engine Unit Repair.
INSTALLATION PROCEDURE


  1. Install the engine oil pan and a NEW gasket. Refer to Oil Pan Installation under Engine Unit Repair.
  2. Lower the engine onto the mounts.
  3. Install the engine mount through-bolts.
  4. Install the starter.
  5. Install the flywheel inspection cover.
  6. Install the engine oil filter and the engine oil.
  7. Install the oil filter adapter.
  8. Install the oil level indicator tube.

May 04, 2015 | 1998 Chevrolet Chevrolet silverado

1 Answer

How to do a transmission fluid/filter change on a gmc 1500 2wd v8 350 step by step


Raise the vehicle. Refer to Vehicle Lifting. Place a drain pan under the transmission oil pan. Remove the oil pan drain plug. Remove the oil pan bolts. Remove the oil pan. Remove the gasket. Remove the magnet. Remove the oil filter. Remove the filter neck seal. The transmission oil pan gasket is reusable. Inspect the gasket and replace as needed. Clean the transmission case and the oil pan gasket surfaces with solvent. Install the filter neck seal. Install the oil filter. Install the oil pan gasket to the pan. Install the magnet into the bottom of the pan. Notice: Refer to Fastener Notice in Service Precautions. Install the oil pan to the transmission with seventeen bolts. Tighten the oil pan bolts to 11 Nm (97 inch lbs.) . Apply a small amount of sealant GM P/N 12346004 to the treads of the drain plug. Install the oil pan drain plug. Tighten the oil pan drain plug to 18 Nm (13 ft. lbs.) . Install Dextron Automatic Transmission Fluid. Lower the vehicle.

Jul 04, 2011 | GMC Sierra 1500 Cars & Trucks

2 Answers

Where is trans filter located


Hi,
The follwoing is from the GM Shop Technical Manual.
Changing the filter requires removing the transaxle oil pan and gasket,
Remove or disconnect

bendarden.jpg

  • Raise vehicle and suitably support.
  • Loosen oil pan bolts and drain fluid,
  • Remove oil pan attaching bolts.
  • Remove pan pan and gasket.
  • Remove the oiil filter using a long screwdriver pry filter neck out of the seal.
  • Check oil filter seal for damage or wear. If needed, remove and replace
Install or connect
  • install new oil filter and/or seal.
  • install the old pan gasket since it can be reused, unless sealing ribs are damaged. If damaged, use new gasket.
  • Install the oil pan and attaching bolts.
  • Tighten pan bolts to 13 lb. ft,
  • Lower vehicle.
  • Refill transxle to proper level with DEXRON III or DEXRON-IIE fluid.
  • Checkoil pan gasket for leaks,

May 21, 2011 | 1995 Buick LeSabre

1 Answer

HOW TO CHANGE OIL PAN ON F150


Hi. Here's the procedure on how to change the oil pan.

Things You'll Need:
Drain pan
Crescent wrench
New oil filter
Oil filter wrench
Socket wrench
Socket set
Razor knife
Putty knife
New oil pan
Oil pan gasket
6 qt. of oil
Clean towel

    Draining the Oil
  1. 1 Locate the oil pan directly underneath the engine. The oil pan will be held on to the bottom of the motor by 16 to 18 bolts. The drain plug is at the bottom of the pan.
  2. 2 Loosen the drain plug with a crescent wrench. Allow all the oil to drain in to the pan. Tighten the drain plug when the oil is through draining.
  3. 3 Unscrew the oil filter with an oil filter wrench. Place the oil filter with the waste oil.
  4. 4 Rub new motor oil around the gasket of the new oil filter. Pour 1 qt. of oil in to the filter.
  5. 5 Screw the filter to the filter housing with your hands. Do not wrench-tighten as this will strip the threads and make removal of the filter difficult.
  6. Replacing the Oil Pan
  7. 1 Locate all the bolts holding the oil pan in place. There will be 16 to 18 bolts.
  8. 2 Unscrew all the bolts with a socket wrench. Lower the pan to the ground. If the pan is stubborn, tap it with a rubber mallet to loosen the seal from the gasket.
  9. 3 Scrape clean all the gasket material around the bottom surface of the motor. This will ensure a tight seal with the new oil pan.
  10. 4 Place the new gasket around the new oil pan. Raise the oil pan to the motor and screw in all the bolts. Do not tighten the bolts until all are threaded to the bottom of the motor.
  11. 5 Tighten the bolts with a socket wrench. Ensure that all the bolts are tight.
  12. Adding the New Motor Oil
  13. 1 Open the hood to access the engine compartment. Unscrew the oil filler cap on top of the crankcase. Pull the engine oil dipstick from the tube. Wipe the dipstick clean with a fresh towel.
  14. 2 Pour in 5 qt. of oil in to the engine crank case. Insert the dipstick back in to the tube and pull it back out. Check the oil level against the markings on the dipstick. Fill at 1/2 qt. intervals until the dipstick indicates "Full."
  15. 3 Start the truck and allow it to run for five minutes. Allow the truck to sit for an additional five minutes to allow the oil to drain back to the oil pan.
  16. 4 Check the oil level again. Fill if necessary, but do not overfill.

Sep 21, 2010 | 1995 Ford F150 Styleside Regular Cab

2 Answers

How do you change the oil in a 2005 sunfire


FIRST OF ALL YOU NEED 4.0 QUARTS OF OIL FOR 2.2L 2.3L AND 2.4L OHC ENGINES AND THE 2.2L OHC USES 5.0 QUARTS WITH NEW OIL FILTER.TO GET START YOU NEED A FILTER WRENCH,DRAIN PAN, RUBBER GLOVES WHICH PROTECT HANDS FROM OIL. OILWILL CAUSE CANCER , IF STAYS ON SKIN TOO LONG.YOU NEED TO CRANK ENGINE UP LET IT IDLE 5 MINUTES TO THIN OUT MOTOR OIL SO IT CAN FLOW FASTER.WHEN 5 MINUTES UP.TURN OFF ENGINE.SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS ON SOLID LEVEL GROUND.SLIDE DRAIN PAN UNDER THE CAR OIL PAN. PUT ON RUBBER GLOVES THEN REMOVE OIL PAN DRAIN PLUG ON BOTTOM OF OIL PAN USING A 15 METRIC SOCKET WITH RATCHET WRENCH.WHEN ALL OIL DRIPS.SCREW IN TIGHTEN OIL PAN DRAIN PLUG BACK IN OIL PAN REMOVE OIL FILTER ITS NEXT TO OIL PAN USE SOCKET TYPE OIL FILTER WRENCH IF OIL FILTER IS DOWNWARD POSITION. IF OIL FILTER ON THE SIDE YOU NEED THE BAND TYPE OIL FILTER WRENCH. ****** NOTE THIS THE 2.2L OHC ENGINE USES A OIL FILTER ELEMENT THAT HOUSED INSIDE A RECEPTACLE LOCATED AT THE LEFT FRONT CORNER OF THE ENGINE.YOU UNSCREW THE OIL FILTER CAP THEN LIFT THE CAP AND OIL FILTER FROM THE FILTER RECEPTACLE IN THE ENGINE.SEPERATE THE OIL FILTER ELEMENT FROM THE CAP USING A CLEAN RAG REMOVE OIL DIRT AND SLUDGE FROM THE OIL FILTER CAP AND FROM THE RIM AROUND THE OIL FILTER RECEPTACLES.INSTALL A NEW O RING INTO THE GROOVE IN THE CAP.THEN INSTALL THE NEW FILTER ELEMENT IN THE CAP AND INSERT BOTH INTO THE FILTER RECEPTACLE.SCREW DOWN THE CAP AND TIGHTEN IT SECURELY. WHEN ALL IS DONE POUR NEW OIL IN CRANK CASE.MAKE SURE OIL LEVEL ON DIP STICK ON THE FULL MARK YOU CRANK THE ENGINE.MAKE SURE OIL DRAIN PLUG SCREWED BACK IN OIL PAN.WHEN INSTALLING OIL FILTER FILL IT HALF WAY WITH NEW ENGINE OIL,RUB OIL ON FILTER SEAL TO HELP IT SEAL TO ENGINE.BESURE WIPE OIL FILTER SEAL SURFACE ON ENGINE TO MAKE SURE IT CLEAN. WHEN ALL IS DONE CRANK ENGINE UP CHECK FOR OIL LEAKS.IF ALL IS GOOD LOWER CAR BACK TO GROUND,YOU DONE.

Sep 16, 2010 | 2005 Pontiac Sunfire

1 Answer

Changing the tramission filter on a 2007 Saturn Vue Hybrid


Hello and welcome. here is the instructions for removing the trans filter. you will need to drop the bottom trans pan off to gain access to the filter.


  • Remove the oil pan bolts from only the front and the sides.
  • Loosen the rear oil pan bolts about 4 turns.
  • Lightly tap the oil pan with a rubber mallet or pry in order to allow the fluid to drain.
  • Remove the remaining oil pan bolts.
  • Remove the oil pan.
    Install the oil pan attaching bolts.
    Tighten
    Tighten the bolts to 12 N·m (106 lb in).
    c00c848.gif618143d.gif

    Aug 13, 2010 | 2007 Saturn VUE Green Line

    1 Answer

    How do i change the oil filter on a 1991 cutlass calais? any special tools?


    YOU NEED 4.5 QUARTS OF OIL WITH NEW OIL FILTER.YOU NEED OIL FILTER WRENCH YOU NEED WRENCH TO REMOVE OIL DRAIN PLUG.YOU NEED A DRAIN PAN CATCH OLD OIL.NEED LATEX GLOVES TO KEEP GETTING OIL ON HANDS.OIL DOES CAUSE SKIN CANCER.NOW YOU CRANK CAR UP LET IT IDLE 5 MINUTES TO LOOSEN UP OIL AND SLUDGE.TURN OFF ENGINE.SAFELY RAISE SUPPORT VECHICLE ON LEVEL SOLID GROUND USING JACK STAND.PLACE DRAIN PAN UNDER OIL PAN THEN REMOVE OIL DRAIN PLUG LET OIL DRAIN OUT UNTIL IT STOP DRIPPING. PUT OIL DRAIN PLUG BACK IN OIL PAN. THEN SLIDE DRAIN PAN UNDER OIL FILTER REMOVE OIL FILTER LET OIL DRAIN UNTIL IT STOP DRIPPING.TAKE CLEAN PAPER TOWEL WIPE OIL FILTER SEAL SURFACE MAKE SURE NO DIRT ON SURFACE.TAKE NEW OIL FILTER POUR NEW OIL IN FILTER UNTIL ITS ALMOST AT TOP THEN.RUB CLEAN OIL ON NEW OIL FILTER SEAL.THEN PUT NEW OIL FILTER IN PLACE HAND TIGHTEN IT.POUR 4 QUARTS NEW OIL IN ENGINE CRANK CASE USING A FUNNEL.WHEN DONE.CRANK THE ENGINE CHECK FOR LEAKS AT OIL FILTER AND OIL DRAIN PLUG.IF ALL IS GOOD JOB WELL DONE.

    Aug 11, 2010 | 1991 Oldsmobile Cutlass Calais

    1 Answer

    Oil pump ,,,where is the oil pump located on a 1997 dodge caravan


    Hello
    Welcome!
    Oil pump is located on the oil pan.
    Parts needed,,,oil,,,, oil filter,,,, oil pan gasket,,, oil pump,,,, oil pump pickup tube..
    time to do this,, about 3 hours
    Instructions,
    Raise van place on 2 jack stands
    drain oil remove oil filter fill new filter install.
    remove bolts from oil pan,
    remove oil pan..
    remove 2 bolts that hold oil pump and tube.

    install new pump and tube tork bolts to 45 fp
    replace oil pan gasket and install oil pan
    tork pan bolts to 35" pounds
    install drain plug
    fill with oil
    start and check for leaks

    let me know if i can help more

    Jul 17, 2010 | 1997 Dodge Caravan

    2 Answers

    How to and what tools are nessacery to change oil


    oil catch pan hydraulic cat and ratchet with metric sockets adjustable filter rachet lift car front get on under with oil pan rachets and on the motors side of the car you'll find a bolt on the crank pan just a lonley screw on the bottom of a pan close to where your under loosen screw first then put oil pan under try and loosen screw slowly so when it lets go you can cntrol the flow a little so the oil pan can be put in the proper place to catch the oil let it empty till there is nothing but droplets return screw and tighten back on do not over do it the treads on the pan can be harmed if you over tighten then locate filter put oild pan under filter loosen and the same way as the screw do with the fiter . Before putting in new filter on put some fresh oil on the rubber ring and inside just a little so it goes on smooth your finished under the car now go up top hood open you can put car down by now find oil cap and fill in oil

    Apr 03, 2010 | 2002 Toyota Camry

    1 Answer

    How do I change the tranny fluid in my 1998 cadillac catera


    Fluid - A/T: Service and Repair
    Transmission Fluid and Oil Filter Changing
    REMOVAL PROCEDURE
    1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
    2. Place drain pan under pan
    3. Remove oil pan bolts from front and sides only.
    4. Loosen the rear oil pan bolts approximately four turns.
    5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
    6. Remove the oil pan bolts from rear oil pan and gasket.
    7. Remove front oil pan bolts leaving one corner bolt in loosely.
    8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
    9. Remove the following remaining components:
    ^ The front oil pan bolts
    ^ The oil pan
    ^ The gasket
    10. Remove the oil filter bolts and filter.
    11. Clean the following components:
    ^ The transmission case
    ^ The front adapter case
    ^ The oil pan gasket surfaces with solvent
    ^ Air dry
    ^ All traces of gasket material must be removed
    INSTALLATION PROCEDURE
    1. Install the gasket.
    2. Install the oil filter.
    3. Install the bolts.
    ^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
    NOTICE: Refer to Fastener Notice in Service Precautions.
    4. Install the front oil pan.
    5. Install the front oil pan gasket
    6. Install the front oil pan bolts
    ^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
    7. Install the following components:
    ^ Install the pan
    ^ Install the gasket
    ^ Install the bolts
    ^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
    8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
    pan fill. Fill plug opening using and oil suction gun.
    ^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
    9. Lower the vehicle.
    10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

    Sep 13, 2009 | 1998 Cadillac Catera

    Not finding what you are looking for?
    1995 Pontiac Grand Am Logo

    Related Topics:

    94 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Pontiac Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8215 Answers

    Are you a Pontiac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...