Question about 1993 Buick Skylark

Open Question

How many engine motor mounts are there on a 1993 Buick Skylark 6 cyl

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2920 Answers

SOURCE: 1993 buick skylark serpentine belt removal

there is going to be a tensioner pulley near the front of the motor on top that you have to apply pressure to or you can loosen the alternator and take it off that way,just remember how it came off so you can put it back on

Posted on Aug 13, 2008

Ad
  • 2 Answers

SOURCE: Overheating 1993 Buick Skylark

shorted fan and/or cracked intake gasket

Posted on Oct 28, 2008

  • 120 Answers

SOURCE: 97 buick skylark 4 cyl misfires--changeed

read codes sounds like map. sencer

Posted on Feb 21, 2009

  • 4 Answers

SOURCE: engine wiring for 71 buick skylark 350

its the brown wire open your trunk and you will see a wire next to the trunk lach with a conecter

Posted on Nov 29, 2009

  • 5 Answers

SOURCE: how do you replace heater core on 1993 buick

it could be the electronic switch down under the dash that is faulty, not allowing the flap to close off and cycle the water through the heater core..

Posted on Feb 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Idler pulley removal


this may have already been posted.... but second time wont hurt. watr pmps suck. dis. neg batt. cable. drain coolant. support the engine with somethin. remove rt. engine mount. loosten ur pump bolts only. remove ur serp. belt but make sure u have the diagram to replace it. unfasten idler n remove engine brace. remove pump with pulley. seperate. replace pump. replace the other junk. replace coolant. reconnect batt. run engine.

Jun 21, 2014 | 1993 Buick Skylark

1 Answer

How do I install a serpentine belt on 97 buick skylark? Do I remove motor mount?


Hello
Yes remove the motor mount.You need to have it supported with a floor jack first.

Here is a step by step link to help guide you.

Good luck
http://www.wikihow.com/Change-a-Serpentine-Belt-on-a-1997-Buick-Skylark

Dec 08, 2010 | 1997 Buick Skylark

1 Answer

Where is the solenoid?


If you mean the starter solenoid,it's on the front of the engine(Front wheel drive?)under the exhaust manifold.Toward the right side as you look from in front of the car.
If it's Rear WD,it's on the passenger side,fairly low on the motor.
Either way,it's mounted on the starter motor.
Please rate my post?
Bob

Aug 13, 2010 | 1993 Buick Skylark

1 Answer

What is oil capacity on 1996 Buick Skylark 6 Cyl


Hello sdegroff.
The capacity of your 3.8 liter engine is 4 US quarts or 3.8 liters with a new oil filter.

Nov 27, 2009 | 1996 Buick Skylark

1 Answer

I have a 96 Buick skylark. I just took the egr


That sludge. Isnt that why you are cleaning it? That passage should have a vacuum on it when the engine is running, you may need a stiff wire and carb cleaner to clean it

Oct 28, 2009 | 1996 Buick Skylark

1 Answer

Trying to find out where my motor mounts are for my 91 buick skylark!


Standing in front of car,
1 bottom left of engine
2 2 transmision mounts are on bottom right
3 mount on top or bottom called a dogbone because it looks like one

Jul 21, 2009 | 1991 Buick Skylark

1 Answer

Crank setup 1971 350v8 buick skylark


do you mean firing order?if so and you have a buick engine it is
starting with the driver side cyl 1-3-5-7 the passenger side is 2-4-6-8.line up your crank shaft on the mark it has to be on compression stroke the wires go 1-8-4-3-6-5-7-2. let me know how you do .

Jan 09, 2009 | 1983 Buick Skylark

1 Answer

97 buick skylark wont start


if starter fluid made it chug, I would suspect fuel pump fuse, relay or pump, also fuel filter.

Dec 29, 2008 | 1997 Buick Skylark

3 Answers

Plug wires


Good Day,

You didn't specify your engine size so here's a few diagrams:

29d6d5f.jpg2.0L 4cyl

fb6d0e2.jpg3.0L 6cyl
618de1a.jpg3.1L 6cyl
1e777e9.jpg3.3L 6cyl

I have labeled these according to engine size, make sure you use the right one.

Good Luck and hope this helps

Jul 01, 2008 | 1993 Buick Skylark

Not finding what you are looking for?
1993 Buick Skylark Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...