Question about 1988 Chevrolet Cavalier Z24

1 Answer

Where is the crank censor located? - 1988 Chevrolet Cavalier Z24

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,051 Answers

Hello there :on the back side of the block closest to the fire wall about 1/2 way down the block you will see 2 sensors the one that is the closeset to the middle of the block is your crank sensor and the one that is off to the drivers side is the camsaft sensor
Please note be very careful when removing the wires from these cause they can be pulled away from the boot and render them useless
Hope this is very helpful for you
Best regards Michael

Posted on Sep 28, 2010

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: crank positioning censor

The camshaft position sensor is located on the timing cover on the front of the engine. The crankshaft position sensor is located just above the differential on the transaxle bell housing where it has to be to read from the flywheel the position of the crankshaft. It is easy to see from the front of the engine even though it is on the back half. Just look for the shifter cable and where its bracket ends (on the firewall side of the bracket) glance about 12" to the left and you should have no problem finding it. An 8 mm bolt is holding it in and with that bolt taken out it just pulls out of its hole. Google "95 caravan crankshaft position sensor" and then pick IMAGES so you can see an actual picture of what it looks like.

Posted on Oct 13, 2008

JShreader
  • 50 Answers

SOURCE: Need to replace external crank position censor - need schematic

Hello tsutor, my name is JShreader. Thank you for choosing fixya.com.

There are 2 on this Engine. I uploaded a .pdf with pictures showing both of their locations. You can download it by clicking HERE. I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader!

Posted on Apr 01, 2009

  • 25 Answers

SOURCE: I have a 2004 mercedes

Pretty sure the sensor is on the top of the gearbox bellhousing, and picks up its pulse from the flywheel on this model, its held in by allen bolts and is easiers to access from underneath the vehicle ( just above starter location

Posted on Sep 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know where the crank censor is on a 02 Hyundai santa fe


THE CRANK SENSOR IS LOCATED ON THE ENGINE BLOCK NEAR TRANSMISION BUT CALL YOUR DEALER THIS TRUCK HAVE A RECALL FOR THE SENSOR

Oct 05, 2014 | 2002 Hyundai Santa Fe

1 Answer

I replaced the timing belt and crank shaft censor on my 2002 sedona.im not getting a fire from my coil packs.i ran a test it said crank shaft censor,tried a new censor..same problem,same results.what could...


it might be this sensor I can't think of the name of it but it is located by the thermostat. it is held on with 2 10mm bolts and has a connector similar to the mass sensor on it. This sensor controls spark.

Oct 17, 2013 | 2002 Kia Sedona

2 Answers

CAN NOT LOCATE THE CRANK CENSOR


the crank sensor is located on the pass. side attached to the transmission bell houseing with i 10 mm. bolt and a 3 wire connector. ramundoo

Mar 01, 2011 | 1999 Dodge Intrepid

1 Answer

I have a 2004 mercedes c240 and have a new crank censor to install. Where is the censors location on the 6 cylinder?


Pretty sure the sensor is on the top of the gearbox bellhousing, and picks up its pulse from the flywheel on this model, its held in by allen bolts and is easiers to access from underneath the vehicle ( just above starter location

Sep 19, 2010 | Mercedes-Benz C230 Cars & Trucks

2 Answers

Where is crank position sensor on 92 Oldsmobile 3.3 litre and how do I test it


its located right behind the balancer. remove the balancer you will see the shield remove the shield and the sensor is located right behind it secured by a bracket.

Jul 20, 2009 | 1992 Oldsmobile Cutlass Ciera

1 Answer

My '95 Bonneville is running rough and idling low and is shutting off and is very hard to crank


This probably is the mass air flow censor located just behind the air cleaner in the metal part of the throttle body. Wiggle the connector if it stumbles or shuts off the connection inside the censor is bad. You will need to replace the censor.

Jul 12, 2009 | 1995 Pontiac Bonneville

1 Answer

Where is the crank and cam censors located in a 2003 gmc safari


Crank sensor is right behind your harmonic balancer (3 or 4 pin connector). You cam sensor is in your distributor under your rotor...

Jul 01, 2009 | 2003 GMC Safari

1 Answer

Need to replace external crank position censor - need schematic


Hello tsutor, my name is JShreader. Thank you for choosing fixya.com.

There are 2 on this Engine. I uploaded a .pdf with pictures showing both of their locations. You can download it by clicking HERE. I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader!

Mar 30, 2009 | 1998 Chevrolet Lumina

1 Answer

Dodge 2500 5.7 crankshaft censor replacment


The crank sensor is located on the right or passenger side of the engine, at the back on top of the transmission bell housing. It is held in with two bolts and has a single electrical plug on it. Hope this helps and good luck.

Jan 17, 2009 | 2005 Dodge Ram 2500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...