Question about 1996 Ford Club Super

1 Answer

I have a 1996 ford e-350 club wagon with a 7.5 liter engine. when the engine is at operating temp and i put the transmission in reverse the idle drops rapidly and the engine stalls out. after restart it go into reverse nornally without stalling. i have checked the idle control valve and it seems to be operating properly. what gives?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had a similar problem on my 2001 gmc savana. In the end it turned out to be a small hole into one of the hoses that creates vaccum in the engine. I'm no mechanic so don't quote me on that. Hose was replaced and the problem went away. Hope this helps.

Posted on Nov 18, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring diagram ignition system 1996 ford club wagon


Hello Kurt Klasen,

I'm seeing "CLUB WAGON" under ECONOLINE.

Notwithstanding FREE schematics for MOST USA market vehicles at BBB Industries TECHNICAL BULLETINS site...
(are well worth the required registration)
((no memberships... no hassles))...

1996 ECONOLINE is there...!

I always recommend getting the FACTORY REPAIR MANUALS
for the very best & relevant information.

BBB Industries Premium Alternators Starters Power Steering Products

Nov 26, 2016 | Ford Cars & Trucks

1 Answer

AT TIMES TRANSMISSION FLUID GETS VERY HOT AND THEM DUMPS OUT ABOUT 7 QUARTS OF ATF AFTER COOLS DOWN OPERATES FINE.ENGINE TEMP NORMAL.NEW TRANS,MODINE RADIATOR,AFTERMARKET OIL COOLER,CLEAN FLUID.HAPPENS...


If that is the e4od transmission ..They are known for that..Ford claims it gets too hot while idling..But you said you had a cooler..You can try taking out the vent and make sure its clear of debri..Its located on top of the transmission..

Sep 24, 2011 | 1990 Ford F350

1 Answer

How do I recover the refrigerant from the rear a/c unit on a 1996 Ford Club Wagon


from the front under the bonnet ,using a proper machine that sucks the gas out

Aug 10, 2010 | 1996 Ford Club Super

1 Answer

I need a new Trans for a 1996 ford Taurus GL wagon.


The best way is to use the vehicle VIN number, here is a link to a Ford Vin Number Look-up site, that will tell you the transmission code and the type of transmission you have:
https://www.fleet.ford.com/maintenance/vin_tools/default.asp

May 23, 2010 | 1996 Ford Taurus

1 Answer

3.2 liter yamaha engine manual IAC valve How do I replace the IAC valve on this engine? Steps? I just bought a new one and I need to get it replaced. FORD 1994 Taurus SHO 3.2 liter engine YAMAHA


may just need cleaning with carb cleaner.

here is 1996, oldest I have:

Section 03-14: Engine Controls, Electronic 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Idle Air Control (IAC) Valve Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Disconnect the engine control sensor wiring (12A581) from the idle air control valve (IAC valve) (9F715) at the idle air control valve electrical connector.
  1. Remove the two idle air control valve retaining bolts.
  1. Remove the idle air control valve and idle air control valve gasket.
Installation
  1. NOTE: If scraping is necessary, be careful not to damage idle air control valve gasket surfaces, or drop material into intake manifold (9424) or throttle body (9E926) (depending upon application).

    Clean idle air control valve gasket mating surfaces.
  1. To install idle air control valve, reverse Removal procedure.
  1. Tighten the idle air control valve retaining bolts to 8-12 Nm (71-106 lb-in).
33b4417.gif

Jan 14, 2010 | 1994 Ford Taurus

2 Answers

Trying to find out how much oil the Triton V-10 takes when I do my oil change? I cant seem to find it or anyone who knows


It should be listed in the owners manual, but because of different oil cooler setups you may have to do the change yourself and add oil until the correct level is established..... for the first oil change.
Most likely 7 liters,but start with 5,run the engine to fill the oil filter,let it sit for 5 mins and recheck and fill to full.
Note the amount needed for next time.

Nov 08, 2009 | 2000 Ford F250 Super Duty Crew Cabs

3 Answers

Where can i get a free owner manual for a 1992 ford e350 club wagon


Unfortunately Ford doesn't supply a download for guides older than 1996.
If the changes were minor (they often are), the '96 version should help:
1996 E350 manual

Nov 06, 2009 | 1992 Ford Club

Not finding what you are looking for?
1996 Ford Club Super Logo

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...