Question about 2000 Plymouth Neon

Open Question

2000 ply neon engine brackets and locations on 2.0 engines were removed ?two months ago by someelse and i don't know where they go can you or do you have a schemetic for one

Posted by on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 4044 Answers

SOURCE: how can I adjust the

loosen the Adjustment screw on the Clutch master cylinder, carefully lift the pedal upward and connect the push rod to the pedal pin, Tighten the push rod adjustment screw, verify the the clutch operates correctly. (Haynes Repair Manual page 8-5, section 9 step 11 through 14) I highly recommend you get the Haynes repair manual on the vehicle ISBN: 978-1-56392-596-2 as it is possible that your vehicle may have a hydraulic clutch and if it does the steps to adjust the clutch assembly are more entailed.

Posted on Sep 28, 2010

  • 122 Answers

SOURCE: i bought a radio from a 02 neon w/wire bracket but

I would say you need wiring diagrams for both. then you can compair to see if you can splise them. hear you go.


Posted on May 07, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

2000 dodge neon will run on starting fluid once,then no start

You're either out of gas or you need a new fuel pump.
Roll the keys back to the 'off' position.
Have someone sit by the back tire and listen as you roll the key forward until the lights on the dash come on DO NOT CRANK THE ENGINE OVER.

If they hear the pump then you're out of gas, if they don't hear the pump your pump is likely burned up.

Feb 07, 2012 | 2000 Dodge Neon

2 Answers

What does an Engine Mount Bracket look like on a Dodge Neon 2000?

it has more than one motor mount there is one in front of vehicle lower part by radiator its a bracket that holds the motor mount attached to frame almost in the middle of motor and transmission there is another one in front of engine i holds motor mount to the body of car

Feb 17, 2011 | 2000 Dodge Neon

2 Answers

Hello, While driving on the interstate my 2000 Dodge Neon just went dead (like running out of gas) just bought it couple days ago. Car was parked in a yard for over six months. Trying to get engine running...

"within an aluminum like cylinder were plugs are located deposits of engine oil covering almost entirely the spark plug."

Those are the Spark Plug Wells you are referring to. I just had the same issue. It sounds like you need to replace the valve cover gasket and Spark Plug Well Gaskets. The entire kit including the gaskets and rubber o-rings for the bolts is about $50 Canadian. My mechanic quoted 1/2 hour labour. Plugs are about $16 for 4. I chose to change the seals myself, but unless you have th tools and the time and the chemicals already, I'd advise getting the job done professionally.

Aug 10, 2010 | 2000 Dodge Neon

2 Answers

I just need to know where the alternator is located on a 2004 dodge neon 2.0L SXT

Fig. View of the alternator after removing the splash shield - 2.0L engines


Removal & Install - 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Alternator jam nut, loosen only Alternator adjustment nut, loosen only Accessory drive splash shield Alternator lower bolt, loosen only Alternator drive belt Alternator field circuit wiring connector, push the RED locking tab to release Battery positive terminal Upper and lower bolts, move alternator off pivot bracket Pivot bracket Alternator

To install:
Install or connect the following:
Alternator Pivot bracket and torque the bolts to 40 ft. lbs. (54 Nm) Alternator, move it onto pivot bracket Alternator field circuit wiring connector, push RED locking tab in until it snaps in place Battery positive terminal Alternator drive belt Tension the drive belt to 100 lbs. (used) or 135 lbs. (new) Alternator adjustment bolt Alternator jam nut and torque nut to 40 ft. lbs. (54 Nm) Alternator mount bolts and torque the bolts to 40 ft. lbs. (54 Nm) Accessory drive splash shield
Negative battery cable

Fig. Alternator mounting-2.4L engine shown


I hope helps with this (remember rated this help) Good luck.

Jan 05, 2010 | 2004 Dodge Neon

1 Answer

On an 01 neon tension pully how do i get the old one off and the new one on?


Jul 09, 2009 | 2002 Dodge Neon

1 Answer

Dodge Neon engine turns over, battery fine but car doesn't start

the timing might have jumped a tooth. hope this helps.

Jul 08, 2009 | 1997 Dodge Neon

1 Answer

Removal of tensioner pulley in a 2003 Dodge Neon

the tensioner is part of the engine mount bracket..not serviced seperately as far as i know

Mar 16, 2009 | 2000 Dodge Neon

1 Answer

Scanner reads code (060)

Location of "ECM" is Under the Air Filter Box

  1. Disconnect the negative battery cable.
  2. Remove the air cleaner box, refer to the air cleaner box.
  3. Remove the gray and black connector from the PCM.
    1. Remove the harness clip bracket from PCM bracket.
    2. Remove the nut from the upper bracket mount.
    3. Raise vehicle and support on hoist.
    4. Remove 2 lower bracket bolts.
      1. Remove 4 screws from bracket and remove bracket from PCM.
      1. Install bracket to PCM and tighten screws.
      2. Install PCM and bracket to body and tighten the 2 lower bolts.
      3. Lower vehicle.
      4. Install upper bracket nut and tighten.
      5. Clip in wiring harness bracket.
      6. Install gray and black connectors to the PCM.
      7. Install the air cleaner box, refer to the air cleaner box.
      8. Connect the negative battery cable.

Mar 14, 2009 | 2001 Dodge Neon

3 Answers

2002 dodge neon gauges

hi, i have had this problem on a vehicle a couple of years ago, it turned out to be the voltage stabilizer on the back of the clocks, a good auto electrician should locate it and replace it for you, they are cheap to buy, hope this helps, thanks for useing fixya

Feb 21, 2009 | 2002 Dodge Neon

2 Answers

2000 dodge neon won't start. Makes clicking sound and trip fuse indicator is lit on the display panel. Changed the battery terminal. Battery indicator also lights up on the display panel.

look everyone !!! i am not the only one who has this problem , but I found the answer on my own.... iI hope this can help others . If you have to replace a neon engine you must do these thing if you want it to start.
Lower vehicle and perform camshaft and
crankshaft timing relearn procedure as follows:
² Connect the DRB scan tool to the data link
(diagnostic) connector. This connector is located in
the passenger compartment; at the lower edge of
instrument panel; near the steering column.
² Turn the ignition switch on and access the “miscellaneous”
² Select “re-learn cam/crank” option and follow
directions on DRB screen

Most people don't have access to this scanner <but it must be done> I used a snap-on cost 3000 but have the reset feature

Thanks you all for your help.

Jul 26, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
2000 Plymouth Neon Logo

Related Topics:

315 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides