Question about 2007 Chevrolet Impala LS Sedan New Cars

Open Question

How do you replace the blend door actuator oon a 2007 Chevorlet Impala?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Blend door

ok first put you front seat down and back raise steering wheel . now lay on you back with you head in the drivers floor board. look up see 2 screws remove them and the panel they hold on . look to left main wire harness needs to be moved to the right , up and behind it is th blend actuator 7/32 socket to remove it then manually turn the white peg , total labor 30 min

Posted on Dec 15, 2008

emissionwiz
  • 75822 Answers

SOURCE: Blend door not working.

The bleed door controls air temp not where it comes out, dash, floor, defroster, this is most likely a mode control switch problem, that switch is on the ac control head.

Posted on Sep 23, 2008

oldfishead
  • 155 Answers

SOURCE: new blend door actuator doesnt operate

had this problem before... recheck part#....is it for EATC or MANUAL...??? eatc on a manual will only go to half way...sounds like they gave you the wrong part....its a pain to replace wasn't it.....hope this helped you...GL

Posted on Jul 06, 2009

  • 4336 Answers

SOURCE: I need t replace the Air blend door actuator on my

This solution is not for a novice. Air flow doors are fragile and easy to damage.

Posted on Sep 07, 2009

  • 5 Answers

SOURCE: how to replace blend door actuator in a ford

I recently did mine, I hear you can do it without taking the entire dash apart but I had no luck with it myself. I have to get ready for work but, on mine it was located down and to the left of the radio. its a white box...are you hearing a clicking noise or something? I had to roll the entire dash back and it was still a major pain getting it out.

Posted on Dec 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2003 chevy impala. When you turn the switch to heat or defrost the air still comes out of the front vents. Winter is coming


some of the dash may need removal to fix that
not a normal service or maintenance job

faulty directional flaps /or switch levers ?

directional flaps either motorized or vacuum actuators

an example 2003 will be close to this set up
How To Replace Chevy Heat Door Actuator Impala 2006 2013
26318874-eqnsd0j5dazk1edooe0d0ozr-3-0.jpg

Oct 19, 2016 | 2003 Chevrolet Impala

1 Answer

Trying to figure out the required positioning of the blend doors in a 2007 dodge dakota


Does it have an electric control actuator ? An it's mode door not blend door . Mode door controls where air comes out of , defroster , vent , floor etc... an the blend door controls the temp. Pull the mode door actuator an see if the door move's freely , not binding . After replacing an evaporator if everything was put back right you shouldn't have this kind of problem . There is no relearn for the door actuator . Double check your work is the best answer anyone could give !

Jul 30, 2016 | 2007 Dodge Dakota Quad

1 Answer

How do I replace blend door actuator on a 2007 chevrolet impala vehicle?


Most likely have to remove your dashboard.
YOUTUBE has a lot of videos about this subject.

Jan 28, 2016 | Cars & Trucks

2 Answers

How do I change the door blend actuator on my 2003 impala


most door lock actuators are located within the driver door and each of individual doors. Its a small motor about $5.

Feb 17, 2015 | Cars & Trucks

1 Answer

Drivers side blend door actuator not working properly. replaced actuator, when plugged in before installing actuator runs constantly. Is the problem in the control board or in the dash?


Hello: I have bad news for you, if you run the actuator without it connected to the door the actuator is ruined, it will have to be replaced. After replacement the system has to have the doors (actuators re-calibrated.) re-calibrated. This is done with a Tech 2, A GM special tool.

Nov 12, 2010 | 2005 Chevrolet Impala

2 Answers

2006 impala heater motor blows like normal but some mornings it blows cold if we shut it off and turn it on a couple of times it will blow hot and work fine. the heat gauge is at half way when the engine...


this problem is caused by a sticking air temperature control blend door actuator or blend door, this door moves back and forth to get the desired temp, the actuator is electronic and prone to this type of problem, suggest u replace it.

Sep 23, 2010 | 2006 Chevrolet Impala

3 Answers

My 2002 Chevy Impala blows out cold air when I turn my heat on, even after the car is warmed up. PLease help.


this is caused in most cases by the air temp control blend door actuator being defective.

Dec 17, 2008 | 2002 Chevrolet Impala

2 Answers

Hacv controle


It is the actuator part there are a couple of them have to lye on back to get to up by the gas pedal tight fit area had to replace them myself to.

Sep 03, 2008 | 2005 Chevrolet Impala

Not finding what you are looking for?
2007 Chevrolet Impala LS Sedan New Cars Logo

Related Topics:

1,478 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...