Question about 1995 Ford F250

1 Answer

I replaced brake shoes and brake pads, bled brakes, still have spongy brakes

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 270 Answers

Hi:

Your Masre Cylinder needs bled or its only working for front r back:

#2- To much shoe to Drum Brake Clearance

Posted on Sep 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced front pads on my 1999 Nissan Sentra. Brake pedal felt low.Had system flushed, bled and rear shoes adjusted. Still have low pedal and spongy feel. Suggestions?


have had this on different models and makes and what i do is to push brake pedal down and jam it down a length of wood or anything that holds the pedal down a bit not hard down -and leave overnight .if this fails then renew the master cylinder

Dec 03, 2016 | 1999 Nissan Sentra

1 Answer

REplaaced brake pads and spped sensor on 2006 gmc sierra now brakes are spongie at times and have bled them.


DEPENDS WHAT PROCEDURE YOU USE TO REPLACE THEM.IF YOU PUSHED THE CALIPER PISTONS IN WITHOUT OPENING THE BLEEDER AND USING A **** CLOSED THE BRAKE HOSES YOU MANAGED TO SENT BACKWARDS THE FLUID INTO THE MASTER CYLINDER WHERE IS THE POSSIBILITY TO CAUSE THE SEALS ROLLING IN AND ARE NOT HOLDING PRESSURE. THE OTHER REASON IS EITHER YOU NEED TIME UNTIL THE BRAKES BED ON THE DISCS SURFACES.

Aug 30, 2012 | 2006 GMC Sierra

1 Answer

My kid bought a 99 Grand Am, the brakes were spongy and had to be pumped. The car now has new front calipers, pads, and new master cylinder. We bench bled the master cylinder and bled out the brakes. The...


If the car has Drum style rear brakes, make sure the adjustment is good. It takes a lot of fluid to activate them.
PS. I assume you did bleed the rears.

Apr 12, 2011 | Pontiac Grand Am Cars & Trucks

1 Answer

Replaced booster on brakes brakes are spongy


Spongy brakes are caused by air in the hydraulic lines, or old/weakened brake hoses. They may also feel sponger if the brake pads/shoes are excessively worn.

Mar 07, 2011 | Chevrolet 3500 Cars & Trucks

1 Answer

Spongy brake pedal on 2003 Frod escort zx2.


loosen of the hand-brake adjustment and press the brake pedal a few times to self adjust the rear brakes.
Re-tighten the handbrake adj last.
Front brake sounds like a seized caliper,If possible remove caliper and clean and lubricate the piston.
This may work but replacement caliper may be the only other solution.Make sure the caliper slides are also clean and lubricated and the brake pads are in good order.(TRY THIS FIRST)
Also new brake shoes can make the pedal feel spongy for a couple of hundred miles until they have been run in.

Jul 04, 2010 | 2003 Ford ZX2

2 Answers

Spongy brake pedal even after ABS bleed and base brake bleed.


Did you adjust the rear shoes out? If the rear drum brakes are out of adjustment they will give you a lot of pedal travel. If the pads are worn have no fear of that U-CLIP brake spring, just change one shoe at a time. Take the spring off one side, change the shoe, put the spring back on the post and do the same to the other shoe, no problem.

Dec 03, 2009 | 2001 Chevrolet Venture

1 Answer

Put new brake pads and shoes, turned rotors and drums, bled brake lines and still have spongy brake pedal. has kelsey hayes abs


HAve you troublesot the ABS?

One thing it DOES sound like is the power brake booster. The vacuum size has a leak.

Oct 07, 2009 | 1997 Chevrolet C/K 2500

2 Answers

Spongy brake pedal


I have a 2001 Chevy 1500 4 X 4 that recently had all new pads, rotors, and calipers installed. Since then my brake pedal goes almost to the floor before I get any brakes. I took it back to the shop and they bled the brakes with no better results. I bled them also with no results. I took the truck back and they installed a master cylinder with no results. It's now at the Chevy dealer and they say it's normal - BS! I had good brakes before I had all of the brake parts replaced, no one can figure it out. If you have a load in the truck or if you tow anything you better be looking at the ditch to avoid an accident. The original brakes would put you nose into the windshield and now I could stop it better the Fred Flinstone way. Anyone have an answer????????

Jun 18, 2009 | 1998 Chevrolet C1500

3 Answers

Brakes are still spongy after changing the pads, one caliper, and master cylinder. bled front brakes.


I just went to Brake Masters this morning and had them replace the Master Cylinder since I was experiencing the pedal very spongy and going to the floor. When they replaced the Master Cylinder and they gave me back the car, the brakes were still spongy and going to the floor. I addressed this to them and they took another look at it, but when I took it for a second time, the brakes were extremely spongy. It was almost like they gave me back my car in worst condition to when I brought it in. Can you help?

May 21, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Spongy brakes 1996 Chevy C1500


You can adjust the shoes outward on the rear by removing the wheels and drums, then above the axle but below the wheel cylinder you will see an arm that is horizontal, pushing both of the shoes outwards. There should be an adjustment nut that you can turn to extend the arm to push the shoes out.

Apr 22, 2009 | 1996 Chevrolet C1500

Not finding what you are looking for?
1995 Ford F250 Logo

198 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...