Question about 1998 Saturn SL

1 Answer

R & R Multifunction switch - 1998 Saturn SL

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

Unless you are trained, then you will take the car to a GM dealer have them pull the steering wheel , replace the switch, and reinstall the steering wheel. if you are not trained then you will have problems as the airbag is inside the steering wheel and that will no longer work and the airbag light will always be on, and you could accidentally deploy it.

Posted on Sep 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 ford escape wiper and washer has no power. cant hear it engage when on but was working a week ago. how can i troubleshoot it and find the fuse


Hi Justin , Do you know what a SJB - smart junction box is and where it is located on you escape ?
Windshield Wiper Operation
The smart junction box (SJB) supplies power to the multifunction switch from the SJB fuse 25 (20A) when the ignition switch is in the ON or ACC position. The multifunction switch supplies power to the windshield wiper motor for the HIGH or LOW/INTERMITTENT input, depending on the multifunction switch position selected. The SJB also supplies power directly to the windshield wiper motor from fuse 25 (20A) when the ignition switch is in the ON or ACC position for RUN/PARK operation. When the multifunction switch is in the LOW, HIGH, or INTERMITTENT position, power is supplied to the windshield wiper motor, which moves the wipers off the park position. Once the wipers are off the park position, an internal switch in the windshield wiper motor switches to the run/park position which directs power to the wiper switch then back to the wiper motor. This maintains power to the windshield wiper motor to complete the wipe cycle. When the cycle is complete, the internal switch in the windshield wiper motor switches back to the park position. If the multifunction switch is in the LOW or HIGH position, power is supplied from the multifunction switch and another wipe cycle starts. If the multifunction switch is in the INTERMITTENT position, the windshield wipers remain parked until the internal relay in the multifunction switch supplies power to the windshield wiper motor. The internal relay supplies power after a time delay that is determined by the 1 of 9 intermittent switch settings.

Jan 08, 2017 | 2005 Ford Escape

2 Answers

Where is the windshield wiper fuse located in the fuse box on a 06 crown victoria


drivers side inner fender under the hood, look in the owners manual for the number and amps. some are marked under the lid itself

Mar 19, 2015 | 2006 Ford Crown Victoria

1 Answer

Brake lights & Hazzard lights don't work; fuse ok... High mounted center brake light works... Turn signals work...suspect problem is multifunction lever Power drain to battery constant...2...


As for the brake lights push brake pedal down while pushing on and wiggling the hazard switch.If the brake lights come on then replace the multi-function switch.

Aug 10, 2011 | 1997 Oldsmobile Bravada

1 Answer

Is the multifunction switch and the trun signal switch the same


I depends - it is considered a multifunction switch when the turn signals do multiple things. On Ford vehicles the switch generally controls wipers as well. If your turn signal switch has additional controls - then it is a multifunction switch.

May 27, 2011 | Ford Expedition Cars & Trucks

1 Answer

How do I replace the signal switch assembly on my 2004 Chevy Cavalier?


Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF , unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.
  1. Disconnect the negative battery cable.
  2. Remove the steering column trim covers.
  3. Remove the retaining screws from the multifunction switch.

    0996b43f802054ac.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Remove the multifunction switch (2) from the steering column

  4. Remove the multifunction switch from the steering column.
  5. Disconnect the electrical connectors from the multifunction switch.

To install:
  1. Connect the electrical connectors to the multifunction switch.
  2. Install the multifunction switch to the steering column while depressing the spring loaded horn pin.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the retaining screws to the multifunction switch and tighten the screws to 36 lb inches (4 Nm).
  4. Install the steering column trim covers.
  5. Connect the negative battery cable.
  6. Ensure that the multifunction switch functions properly.

Sep 27, 2010 | 2004 Chevrolet Cavalier

1 Answer

Headlights, both low and high beams won't come on


Start, check for 12Vpwr. eng. comp fuse box 30A runs into the multifuction switch.
Head light sw. runs into the multifunction switch.
out of multi sw. pass. comp. fuse box 20A # 38 for high beam
out of multi sw. two 10A fuses #10 & #4 for low beam
make sure you grounds ar good G102 & G103
G102 LH front eng. comp.
G103 RH front eng, comp.

Sep 12, 2010 | 2001 Ford Mustang

1 Answer

Multifunction Switch works intermittantly. When the blinkers and wipers stop, have to Bang on the steering column, then it works again. Goes in spurts, have to bang for a week or 2, then it works fine...


Multifunction Switch -I suspect this switch or the connection at the harness is bad or contaminated. Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove the upper and lower steering column shrouds.
  3. Disconnect wire connector from the back of the multifunction switch.
  4. Remove screws holding multi-function switch to steering column adapter collar.
  5. Remove the multi-function switch.
To Install:
  1. Position the switch on to the steering column and install the mounting screws.
  2. Connect the electrical connectors to the switch.
  3. Install the upper and lower steering column shrouds.
  4. Connect the negative battery cable.
prev.gif next.gif

Aug 17, 2010 | 2005 Chrysler Town & Country

3 Answers

How to replace my turn signal switch


Multi-function Switch Removal & Installation To Remove:
To Remove:
  1. Remove the steering column trim covers.
  2. Remove the wire harness from the retainers as needed.
  3. Slide the turn signal and multifunction switch connectors out from the bulk head connector.
  4. Remove the two mounting screws and remove the multi-function switch from the steering column.

To Install:
  1. Install the multi-function switch on the steering column.
    • Tighten the screws to 42 lb in (4.7 Nm).
  2. Slide the turn signal and multifunction switch connectors into the bulkhead connector.
  3. Install the harness in the original retainers.
  4. Install the steering column trim covers.
7f81df3.gif

Jun 25, 2009 | 1996 GMC Sierra

Not finding what you are looking for?
1998 Saturn SL Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...