Question about 1990 Toyota 4Runner

1 Answer

Front Rotoe removal 1990 Toyota 3Runner

I am down to the removing the cap on the fron t wheel holdin gon the rotor, how do I remove the assembly unit to replace the rotor?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 330 Answers

Take off the disk pad, release the pressure.
1. Loss the brake fluid small fitting on the cylinder, then use one hand slowly loss the fitting and use another hand with flat screw driver pressure the brake pad toward the piston of the cylinder AT THE SAME TIME , as soon as you release the pad a little bit, close the fitting right away, DO NOT LET THE AIR GET INTO YOUR BRAKE LINE. After you release the pad, TIGHT the fitting.

2. Take off two screws behind the cylinder which connected to the body and remove the cylinder first and then take off the rotor.

3. When you put back, don’t touch the fitting, after you finish it, check everything is O.K. then start the car, pump the brake several times, until you feel the brake is normal.


For your safety, use emergency brake and also put something behind your rear wheel to completely stable the car.

Good luck, hope this can help you.
Frank

Posted on Jul 09, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 toyota tacoma replace front wheel bearing prerunner


The other guys have never taken the wheel bearings out of a 2007 Tacoma! Remove the tire (duh)
Remove the 12mm bolt holding the brake line securing bracket
Un-clip the air sensor hose clip
Remove the two 17mm bolts holding the brake assembly on the back side
Remove the rotor from the wheel "spindle"- slides right off.
Unscrew the four metric bolts (maybe 17mm) holding the wheel housing to its mount (they cannot be removed from the assembly yet, see below).
That's right there is no normal wheel spindle with a big nut on the end of a threaded shaft in the middle!
The wheel mounting plate (with the 6 studs) is pressed into the bearing housing.
Get a replacement bearing assembly and take it and your old unit to a machine shop (unless you have a good press).
An easy job, just expensive- $140 for the bearing assembly.

Mar 27, 2012 | 2007 Toyota Tacoma

1 Answer

1991 Honda Accord had the brakes change new rotors and pads. Drove 50 miles and the front drive axle where it goes into the front wheel looks and acts like it is stripped out. It's making bad noise if you...


Brake Disc (Rotor) REMOVAL & INSTALLATION 1990-95 Accord
  1. If equipped with an air bag, disconnect the negative battery cable and properly disable the Supplemental Restraint System (SRS), as detailed in Section 6 of this manual.
  2. Loosen the lug nuts, then Raise and safely support the vehicle on jackstands.
  3. Remove the wheels.
  4. Remove the steering knuckle from the vehicle. Please refer to Section 8 for procedures.
  5. Remove the 4 bolts retaining the hub unit to the steering knuckle and remove the hub unit. Fig. 4: Remove the 4 bolts retaining the hub unit to the steering knuckle and remove the hub unit/rotor assembly 86809032.gif

  6. Remove the 4 bolts, then separate the hub unit from the brake rotor. Fig. 5: Remove the 4 bolts, then separate the hub unit from the brake rotor 86809033.gif
    To install:
  7. Assemble the disc to the hub unit and tighten the bolts to 40 ft. lbs. (55 Nm).
  8. When installing the hub to the knuckle, use new self-locking bolts and tighten them to 33 ft. lbs. (45 Nm).
  9. Install the steering knuckle.
  10. Lower the vehicle and check for proper brake operation.
  11. If equipped, enable the SRS system and connect the negative battery cable.
prev.gif next.gif

Oct 29, 2010 | 1991 Honda Accord

1 Answer

How do you tear down front hub on 4 wleel drive truck?


FRONT DRIVE AXLE Manual Locking Hubs DISASSEMBLY AND ASSEMBLY Fig. 1: Three screws retain the cap to the hub body 91197g48.gif
Fig. 2: Remove the lockring seated in the groove of the brake rotor assembly 91197g49.gif
Fig. 3: Remove the hub body assembly from the brake rotor assembly 91197g50.gif
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the three screws retaining the cap and remove the cap from the hub.
  4. Remove the lockring seated in the groove of the brake rotor assembly.
  5. Remove the hub body assembly from the brake rotor assembly. To install:
  6. The installation is the reverse of the removal.
prev.gif next.gif

Oct 12, 2010 | 1997 Ford F250 SuperCab

1 Answer

How do you remove the Hub and Rotor on a 97' F250 with Auto 4 wheel drive? I can not get the rotor to come off. I know that the hub must come with it. However, I am not sure what I have not removed in...


Section 05-03C: Wheel Hubs and Bearings, Front Wheels, 4-Wheel Drive 1997 F-250/350/Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000 Locking Hubs, Manual

e9801b.gif


Item Part Number Description 1 3A329 Halfshaft 2 3C132 Rolling Diaphragm Seal (Axle) 3 3299 Integral Spacer Needle Bearing Seal 4 3123 Bearing, Caged Needle 5 3105 Front Wheel Spindle 6 1190 Wheel Hub Grease Seal 7 4221 Inner Wheel Bearing (with Bearing Cup 4222) 8 1102 Front Disc Brake Hub and Rotor 9 4221 Outer Wheel Bearing (with Bearing Cup 4222) 10 - Pin (Part of 1195) 11 1195 Inner Lock Nut 12 1198 Lockwasher 13 1197 Outer Lock Nut 14 - Steel Thrust Washer
(Part of 3B458) 15 - Plastic Thrust Washer
(Part of 3B458) 16 - Splined Thrust Washer
(Part of 3B458) 17 3B457 Snap Ring 18 1K105 Hub Body 19 - Lock Ring (Part of 1K106) 20 1K104 Cap 21 1K104 Capscrew A - While Rotating Front Disc Brake Hub and Rotor, Tighten Inner Lock Nut to 68 Nm (50 Lb-Ft) to Seat Bearings. Back Nut Off 90 Degrees (1/4 Turn). B - Tighten to 217-278 Nm (160-205 Lb-Ft) C - Tighten to 4-6 Nm
(35-53 Lb-In) Removal
  1. Separate cap assembly from hub body by removing the three Torx® head capscrews.


    de0460a.gif



    de0285a.gif

  1. Remove the lock ring seated in the groove of the front disc brake hub and rotor (1102).


    f4658c.gif

  1. Remove the hub body assembly from the front disc brake hub and rotor. If the body is difficult to remove, install two capscrews and pull the body assembly out of the front disc brake hub and rotor.


    f4659d.gif

Installation
  1. NOTE: Do not pack the hublock body assembly or cap with grease. Excessive grease can cause excessive dialing effort and hub failure.

    Follow removal procedure in reverse order.
  1. Tighten three Torx® head capscrews to 4-6 Nm (35-53 lb-in).

Oct 04, 2010 | 1997 Ford F250 SuperCab

1 Answer

How do you the rotor off a 1990 honda accord lx


REMOVAL & INSTALLATION Except 1990–95 Accord
  1. If equipped with an air bag, disconnect the negative battery cable and properly disable the Supplemental Restraint System (SRS), as detailed in Section 6 of this manual.
  2. Loosen the lug nuts, then Raise and safely support the vehicle on jackstands.
  3. Remove the wheels.
  4. Remove the two 6mm screws from the brake disc. Fig. 1: Remove the two 6mm screws securing the brake disc 86809029.jpg

  5. Disconnect the caliper from the caliper bracket. Support the caliper out of the way with a length of wire. Do not allow the caliper to hang from the brake hose.
  6. Remove the caliper bracket. Fig. 2: Remove the bolt and guide pin from the caliper bracket, then remove the bracket 86809030.jpg

  7. Remove the brake disc. If the brake disc is difficult to remove, install two 8mm bolts into the threaded holes and tighten them evenly and alternately to prevent cocking the rotor. Fig. 3: Remove the brake disc from the caliper assembly 86809031.jpg

  8. Installation is the reverse of the removal procedure.
  9. If equipped, enable the SRS system and connect the negative battery cable.
1990–95 Accord
  1. If equipped with an air bag, disconnect the negative battery cable and properly disable the Supplemental Restraint System (SRS), as detailed in Section 6 of this manual.
  2. Loosen the lug nuts, then Raise and safely support the vehicle on jackstands.
  3. Remove the wheels.
  4. Remove the steering knuckle from the vehicle. Please refer to Section 8 for procedures.
  5. Remove the 4 bolts retaining the hub unit to the steering knuckle and remove the hub unit. Fig. 4: Remove the 4 bolts retaining the hub unit to the steering knuckle and remove the hub unit/rotor assembly 86809032.gif

  6. Remove the 4 bolts, then separate the hub unit from the brake rotor. Fig. 5: Remove the 4 bolts, then separate the hub unit from the brake rotor 86809033.gif
    To install:
  7. Assemble the disc to the hub unit and tighten the bolts to 40 ft. lbs. (55 Nm).
  8. When installing the hub to the knuckle, use new self-locking bolts and tighten them to 33 ft. lbs. (45 Nm).
  9. Install the steering knuckle.
  10. Lower the vehicle and check for proper brake operation.
  11. If equipped, enable the SRS system and connect the negative battery cable.
prev.gif next.gif

Aug 21, 2010 | 1990 Honda Accord

1 Answer

1990 6 cyl. pickup (Toyota). removed rotor and wheel hub...cannot seperate rotor from hub...is there another retention ring on the hub?


not sure on this ,look carefully because it might be a complete unit ,if their isnt two screws on the front of the brake disk then its a complete unit ,Have you bought the disks yet?? check them out if you have to look for the answer

Nov 15, 2009 | 1990 Toyota Pickup

1 Answer

Need to replace the front wheel bearings on a 2003 Ford F150


I am assuming it is a two wheel drive unit. Remove the wheel. Remove the caliper assembly from the axle and support it so it soes not just hang from the brake line. Pull the dust cap off from the center of the axle end. Remove the cotter key fron the nut. Remove the nut. Gently pull the rotor assembly from the axle spindle. Remove the seal on the inside of the rotor assembly. Lift the inner bearing out of the race. Use a drift pin to remove the race from the hub. Be careful not to score the inside of the hub where the race mounts. Do the same process for the outer bearing. Replace the race and make sure it is fully seated. Grease the new bearings. Replace the inner wheel seal with a new one. Slide the hub back onto the spindle. Place the flat washer on the spindle with the nut and seat the bearings to about 20 pounds torque and back off about 1/8 turn and snug again and replace the kotter key with a new one,. Replace the dust cap back onto the hub and your done.

Sep 16, 2009 | 2003 Ford F150 Regular Cab

3 Answers

How do you get to the front wheel bearings on a 1999 toyota tacoma so that i can grease them?


For the most part it is very similar to doing a brake job, you will need to gain access to disc area. once you have removed the caliper you will need to remove the dust cap, this will allow you to remove the nut that secures the disc to the spindle. after you access to the front bearing, remove and set aside, put washer and nut back on, slide rotor out tapping it to remove rear bearing, remove nut/washer and hand pack with wheel bearing grease. re assemble, check and bleed brakes if necessary, Good Luck!
imgres.jpg

Sep 13, 2009 | 1999 Toyota Tacoma PreRunner

2 Answers

Cant remove wheel hub


here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Refer to Section 04-04 .
  1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
  1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
  1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
  1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
  1. Remove inner brake shoe and lining assembly.
  1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
  1. Remove lug bolt from wheel hub (1104).



7548d8f.gif

Installation
  1. Install lug bolt into wheel hub.
  1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
  1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
  1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).

May 25, 2009 | 1996 Mercury Sable

1 Answer

Remove the front disc rotor


The rotor and hub assembly are held together by the studs,you must first remove the 4-wheel drive hub assembly,then the wheel bearing nuts,and pull the hub and rotor off as a unit. Next lay it(back down) on a piece of wood, using a drift punch drive the studs out. Turn it over ,lay it(face down) on a block of wood, line the new stud splines up with the grooves in the hub and drive them in with the punch and reassemble. A set of dentist style picks will be helpful with the clip in the 4wd hub and a 4 lug 4wd nut wrench will be needed.

Dec 26, 2008 | 1979 Chevrolet C/K 3500

Not finding what you are looking for?
1990 Toyota 4Runner Logo

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...