Question about 2007 Infiniti M35 Sport Sedan

Open Question

My VDC off light, slip and brake light all came on at the same time

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jmassengill
  • 345 Answers

SOURCE: replaced braked pads - now VDC and Slip Lights are on

I would take the car to almost any auto parts store and ask them to check the ODB II computer for codes and to reset the "Check engine light". Get the code that they tell you and it should go a long way to pointing you in the right direction to fixing this problem. It might also be that when you pumped the brakes that you somehow set a code in the computer from the ABS system and now that you have the brakes pumped up and working correctly resetting the Check engine light might fix your problem.

Good luck! Write back with any code you get and I'll see if I can help you figure out what the problem might be.

Posted on Jan 06, 2009

  • 10 Answers

SOURCE: 2005 Pathfinder - all warning lights on

was toll before disconnect the battery for five seconds and it will clear all the lights codes

Posted on Jul 09, 2009

  • 6 Answers

SOURCE: Engine sputters while check engine light flashes

The issue is your Mass Air Flow Sensor (MAF) and more than likely also the Intake Air Temperature Sensor (IAT) which is part of the MAF housing. Both are probably malfunctioning. This can be due to an overused/very dirty air filter, or even an aftermarket air filter (that uses oil on the filter element), or diriving in very dusty/dirty areas.

2 fixes.
1) Get MAF cleaner of Electrical connection cleaner in a spray can from your local auto parts store. Locate the MAF, which is on the intake tube, drivers side, just after the air filter. It is held down by 2 hex screws. remove it (try not to touch the metal with your hands, and DO NOT touch the little sensors that look like wire resistors you will see inside, if you touch them, it will no longer work!), spray it VERY WELL with the cleaner (use the whole can if you feel the need) let dry in ambient air for at least 10 minutes, re-install and like magic, your car will start & run, probably better than before you had the issue. The CATCH IS, this can end up being a short term fix, may happen again after 10 miles, or 20,000 miles, but it will more than likely happen again.
2) Replace the MAF with a new unit, or have your vehicle serviced under warranty, and have the dealership replace this part.

Posted on Dec 03, 2009

  • 1 Answer

SOURCE: why did my VDC, slip, ABS and brake lights come on

Hi there,

You should first of all check the fuse for the abs under the hood. If that is ok, then get ready to fork out a couple of thousand dollars to fix it. It is probably the abs actuator, due to a speed sensor malfunction. Both will need to be replaced. Don't bother calling Nissan, they will not help with this issue.

Posted on Jan 22, 2010

  • 86 Answers

SOURCE: 2003 Infiniti G35 - VDC, slip and brake lights on

The abs sensor may have been damaged when the repair was done.

Posted on Feb 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset vdc sensor on 2006 nissan pathfinder?


Is VDC switch turned on? If not check brake fluid level

Aug 07, 2014 | 2006 Nissan Pathfinder

1 Answer

Brake light slip vdc


Check the brake fluid level if it is low do not add. Check the front and rear brake pad if the pad are bad reinstall with a new and
the brake fluid return back to the fluid reservoir
and the system function and all the light on dash turn off

Jul 18, 2014 | Nissan Pathfinder Cars & Trucks

1 Answer

What does Brake light,VDC light and slip lights on . This happened when brake pedal pulsates,but I do have brake pedal.


See if the following information helpful:
1. Keep an eye on the dashboard for the indicators marked "SLIP" and "VDC Off" which will tell you the status of the computerized handling system if handling isn't normal. "SLIP" will blink when VDC is operating. "VDC OFF" means the system is off. Turn the VDC system back on if the Nissan's handling is poor by pressing the "VDC Off" button until the light goes out.

2. Adjust your driving if "SLIP" comes on. "SLIP" means the road conditions may be slippery. The VDC aids in steering and stopping, but be careful, even if VDC is engaged.

3. Remove any aftermarket suspension parts like enhanced shock absorbers if the "VDC Off" light comes on and handling is bad. The VDC system is geared for stock equipment and tires only. Use winter tires or snow chains on snow-covered roads. VDC won't substitute for the correct winter equipment.

4. Don't drive on very inclined corners with high banks and leave the VDC switch on if the handling is poor with VDC on. The system can't operate properly in that environment. Disengage VDC, or avoid those kinds of roads.

May 21, 2014 | 2004 Nissan Titan

3 Answers

If i feel a grinding of my brakes after having my lower control arm and hub bearing replaced why am I steal feeling a grinding when I mash the brakes and it was from a rod connecter broke on the truck and...


I have a 2005 Nissan Pathfinder, the VDC light and the "Slip" light came on the dash, and the slip light was coming on while i was driving at the speed of 20 mph

Jun 24, 2011 | 2005 Nissan Pathfinder

1 Answer

2006 Nissan Pathfinder - VDC and Slip lights come on if you push the brake all the way down (after stoping). Brakes on pathfinders a "spongy" anyway and offer variable resistance depending on...


While it is possible the brake cylinder needs replacing
I would be suspect of what a dealer tells you

If your bold enough to walk into the dealer service
bay from outside and talk to the tech that worked on
it,that would be where to start.

The VDC etc should be diagnosed with the proper
test equipment,scan tool etc.

I would talk to the tech,then go to a local repair
shop and spend some time explaining all the
issues,& make it clear your there only to work on
the Braking Electronics,no other checks or service
of any kind.

Apr 25, 2011 | 2008 Nissan Pathfinder

1 Answer

My brake, slip and VDC indicators stay on.


Check brake fluid level, add fluid from sealed container if needed.

Also check for leaking rear axle seals. Look for oil on the inside of rear wheels.

May 06, 2010 | 2004 Nissan Titan

1 Answer

No solution yet


VDC/ OFF light is still ON only ? or also SLIP + VDC/OFF ?

if VDC/OFF only u must check ur brake fluid status if both VDC and SLIP u still have problems with ur ABS module and steering wheel


Jun 15, 2009 | 2008 Nissan Xterra

1 Answer

Replaced braked pads - now VDC and Slip Lights are on


I would take the car to almost any auto parts store and ask them to check the ODB II computer for codes and to reset the "Check engine light". Get the code that they tell you and it should go a long way to pointing you in the right direction to fixing this problem. It might also be that when you pumped the brakes that you somehow set a code in the computer from the ABS system and now that you have the brakes pumped up and working correctly resetting the Check engine light might fix your problem.

Good luck! Write back with any code you get and I'll see if I can help you figure out what the problem might be.

Jan 06, 2009 | 2004 Infiniti G35 Sport Coupe

1 Answer

Sometimes when i take off fast a slip light comes on does that mean my transmission is slipping?


I found your answer here:

Why Does the SLIP Light Come on?
The SLIP light represents the vehicle's traction control program. When illumiated it takes over control of throttle and braking based on input from a myriad of sensors. The VDC (traction control) is initiated by wheel slip, yaw and any other factors that make the computer think you're on the verge of loosing control of the vehicle. There have been a lot of complaints about the G35's VDC being too interferring and actually causing harder driving conditions. The VDC can be turned off via a switch to the lower left of the steering wheel (useful if trying to pull out of a snowy spot when wheel spin is necessary, or "spirited" accelerating). Even with the VDC turned off, however, it will still kick in if it detects substantial loss of control. NOTE: if you plan on racing, turn the VDC off. Otherwise it will ****** the throttle when you chirp the wheels from 1st to 2nd gear.

Dec 21, 2008 | Infiniti G35 Cars & Trucks

Not finding what you are looking for?
2007 Infiniti M35 Sport Sedan Logo

Related Topics:

393 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14337 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...