Question about 1994 Chevrolet Silverado 2500

1 Answer

1994 chevy 1500 windshield wiper. One works fine, but the other only move 3 inches in the up position and it slides toward the side mirror

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 959 Answers

Your wiper transmission has dislodged itself from the wiper arm on the passanger side...
Take hold of the passanger side wiper arm and see if it moves independantly ( not in sequence with the drivers side wiper arm).

You may be required to remove the fresh air intake valance and install a new ( used?) wiper transmission assembly...
What happens is the plastic cups on the wiper transmission wear out and pop off...
easy fix ya !

Posted on Sep 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to Take off wiper arms on 1994 ford f150


Where the wiper arms attach at the base of the windshield, look on the side of the wiper arm for a small lock that can be pulled out with a small screwdriver, lift the wiper arm and slide the lock out as you release the wiper arm which should now stay in the raised position, slide the wioer arm off the shaft where the arm is attached.

Sep 06, 2014 | 2003 Ford E150

1 Answer

1994 Integra LS 4dr, Wipers range is too far!


remove the wiper arm, and reposition the arm to another position, then try it out to see where it lands. Keep doing that until you find the optimal position. ALSO, On my "teg, the driver's side wiper is 1 inch longer than the passenger side, so be sure you are using the correct length wiper.

Mar 30, 2014 | Acura Integra Cars & Trucks

1 Answer

How do I change wiper blades 2001 Chevy blazer


Open the cap at the end of the windshield wiper arm at the cowl of the Blazer. This will reveal the bolt that secures the wiper arm to the wiper linkage.
Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4pQJ39h
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4pJlPaV
  • 2 Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4p1UYyB

  • 2 Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4p1UYyB

    Jan 15, 2011 | 2001 Chevrolet Blazer

    1 Answer

    Chevy S-10 1994 Wipers don't work at all...cruise works, turn signals work, but no wipers. Fuse is fine


    Park you car in a quite location.

    Engine off

    Turn wiper to high and listen for the motor rotation noise near the firewall (near the bottom of the windshield)

    If you hear the motor rotation noise and the wipers are not moving then it's the linkage and/or the motor clutch.

    Get to it ASAP. A loose bolt connection can damage the linkage arm or clutch.

    It's time consuming to replace these hard to reach park.




    Nov 11, 2009 | 1994 Chevrolet S-10

    4 Answers

    1996 chevy truck 1500. my windshield wipers work


    Check for a loose fuse or loose wiring to the wiper. Also check for tight ground connection at the motor. The 'park' switch which completes each cycle may be intermittent. It might be a worn switch at the steering wheel.

    Aug 25, 2009 | 1996 Chevrolet C1500

    1 Answer

    Need to get a programmer dont know where its at


    • Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF
    • Damaged turn signal and windshield wiper switch .
    • Damaged windshield wiper motor .
    • Damaged windshield wiper control module.
    7fd52e7.gif
    efd7dbe.gif
    Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
    Windshield Wiper System The windshield wiper system consists of :
    • Windshield wiper motor (17508) (F-type).
    • Washer system.
    • Windshield wiper control module.
    • Turn signal and windshield wiper switch (13K359).
    The windshield wiper control module is:
    • Located at the instrument panel fuse panel.
    The windshield wiper motor is:
    • Attached to the cowl top extension (021A36) .
    • Connected to windshield wiper mounting arm and pivot shaft (17566) .
    The turn signal and windshield wiper switch features a:
    • Rotary wiper switch.
    • Push type washer actuator.
    OFF/Low/High Speed
    • Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
    • The windshield wiper motor has a brush rigging that permits selection of low or high speed.
    • When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
    • When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
    • In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
    • When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
    • When the park switch contacts open, the windshield wiper motor stops in the park position.
    Interval
    When the turn signal and windshield wiper switch is in the interval position:
    • The wipers make single wipes separated by pauses.
    • The rotary switch is on the end of turn signal and windshield wiper switch .
    • The length of the pause can be set from approximately 1 to 17 seconds.
    • Length of pause decreases as the rotary switch is rotated away from off.
    • Length of pause increases as the rotary switch is rotated toward off.
    While in the interval wiper mode:
    • It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.

    May 27, 2009 | 1994 Ford Mustang

    1 Answer

    1999 Chevy Venture, Windshield wipers stop in upright position


    You will need to replace the wiper transmission.This is a common problem.

    Jan 24, 2009 | 1999 Chevrolet Venture

    1 Answer

    Windshield wipers wont work when i engage the sprayers


    Try blowing the switch out with compressed air moving it from every position. If this fails, replace the switch. Frankster016

    Oct 26, 2008 | 1994 Honda Civic

    Not finding what you are looking for?
    Cars & Trucks Logo

    328 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...