Question about Dodge Sprinter

1 Answer

Need a Surpentine Belt Routing Picture for a 2006 dodge Sprinter.I Have melted the idler above the altenator three times and damaged 2 belts. I think the routing Pic in the owners guide is wrong. Have replaced the tentioner and both idlers and belt with factory parts.What am I doing Wrong

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,299 Answers

If you have a laser pointer you can point it down and line up all of the pulleys. If you have a pulley out of alignment then this will eat belts. Inspect the lower pulleys such as the harmonic balancer pulley etc. to see if there are any bent or out of alignment from running over things on the road. The belt will only go on one way. Just make sure that the smooth pulleys run on the top of the belt, and the grooved pulleys run on the bottom of the belt. Also if you don't get the idler pulley back on in the proper alignment then it will burn it up also. If you are putting all of the tension on one side of the idler, it will burn the bearings up in it.

Posted on Sep 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 dodge sprinter belt and pulley diagram


There is a belt routing diagram under the hood.

May 18, 2016 | Dodge Cars & Trucks

2 Answers

Diagramm serpantine belt 2005 sprinter2500


Hi.

Here the belt routing for 2005 Dodge Sprinter 2005, whch was sold only with the 2.7 engine mounted:



feac688.jpg


Fig. Accessory Belt Routing-A/C Compressor (1), Power Steering Pump (2), Tensioner (3), Crankshaft Pulley (4), Water Pump (5), Alternator (6), Idler Pulley (7)-All Engines

Here a different view:

62bcecc.jpg

Here also the fan belt routing;

729c6e0.jpg

Fig. Fan belt routing-Fan pulley (1), Fan belt (2), Crankshaft pulley (3)-3.0L engine shown

PROCEDURE Removal & Installation


2.7L Engine

1. Loosen the tension adjust and remove the A/C compressor drive belt.
2. Attach a 3 / 8 inch drive ratchet to the automatic belt tensioner.
3. Rotate the belt tensioner counterclockwise to release the belt tension.
4. Remove the accessory drive belt, starting with the water pump pulley.



To install:

1. Position the accessory drive belt around every pulley except the water pump pulley.
2. Rotate the drive belt tensioner clockwise, install the accessory drive belt and release the tensioner.
3. Position the A/C Compressor drive belt over the crankshaft pulley and A/C compressor pulley.
4. Tighten the drive belt tensioner.
5. Ensure the belt is seated properly on all of the pulleys.

If this solution was helpful, then please do not forget to Accept.
Writing dedicate solution, sharing skills, researching and extracting info from service documents takes time, and your feedback is important for us.
If you repute any solution useful, please click on Accept.

All the best.

Ginko.

Sep 21, 2010 | Dodge Sprinter Cars & Trucks

1 Answer

What size is the engine on a 2002 dodge durango R/T? Need to change the surpentine belt.


4.7L or 5.9L and it should be listed on a sticker somewhere in the engine compartment.

---
Drive Belt Removal & Installation 3.7L, & 4.7L Engines To Remove:
dak_97-04_47l_drv_blt.gif

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect negative battery cable.
  3. Rotate tensioner until it stops.
  4. Remove belt and slowly rotate the tensioner back to its free position.
To Install:
  1. Install new belt and route around all pulleys except idler pulley.
  2. Rotate the tensioner arm until it stops.
  3. Route the belt around the idler pulley and slowly let the tensioner rotate back to its free position.
3.9L, 5.2L, & 5.9L Engines To Remove:
NOTE: Check the belt routing label, located in the engine compartment, for the most current belt routing schematic.
CAUTION
Do not attempt to check tension with a belt tension gauge on vehicles equipped with an automatic belt tensioner.
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Attach a socket wrench to the pulley mounting bolt of the automatic belt tensioner and rotate the tensioner assembly clockwise until tension is relieved.
  3. Remove or disconnect the following:
    • Belt from idler pulley
    • Belt from vehicle
To Install:
  1. Position drive belt over all pulleys except idler pulley.
  2. Attach a socket wrench to automatic belt tensioner and rotate the tensioner assembly clockwise.
  3. Install belt over idler pulley, allow tensioner to rotate back into place, and remove the wrench.
prev.gif next.gif

Sep 03, 2010 | 2002 Dodge Durango

1 Answer

Need to know how to put a serpentine belt on a 1995 302 ford motor


Below the altenator is a tensioning pully, insert a 3/8" ratchet or breaker bar in the square hole on the tensioner and release the tension on the surpentine belt and remove the belt. Route the new surpentine belt in place up to the altenator and take the tension off the tensioner and put the belt over the altenator pully. Double check to make sure the belt is riding correctly on all the pullies before starting. Crank the engine over several times before starting to seat the belt. f78f558.jpg

Jun 02, 2010 | 1995 Ford Mustang

1 Answer

Install a altenator for a 2006 jeep commander


I would rate this a 5 in difficulty. If you have a metric socket set, basic hand tools and a supertine belt tool it's fairly easy repair. You can rent a surpentine belt tool at Autozone.

Disconnect the battery
remove the cowling
remove the supertine belt from the altenator pully
disconnect the red wire on the back of the altenator
disconnect the harness plug from the altenator
remove the bolts holding the altenator to the mounting brackets.
Reverse the process with the new altenator and it it's done.
Make sure your battery is charged before you start the engine a low battery can cause damage to your new altenator.

May 20, 2010 | 2006 Jeep Commander

1 Answer

Surpentine belt routing diagram for 1999 vw beetle


start at crank goes around crank pulley and ac compressor then inside the idler back out around alternator theninside tensioner belt will almost touch itself between pulleys

Jul 22, 2009 | 2000 Volkswagen Beetle

1 Answer

Surpentine belt.


depends on which v8 you have....the 4.7 the routing is as follows it goes under the waterpump pully over the alternator down and around the power steering pumpto the crank...it goes under the bottom of the crank to the idler pully.the flat side of the belt goes ver the idler then around the automatic tensioner to the ac compressor.
on the 5.2 and 5.9 it routes starting at the idler pully the flat side goes undr the idler the up to the ac compressor around the compressor and down to the power steering pump ... around power stering pump to waterpump where the flat side is against waterpump pully around water pump down and around crank up it automatic tensioner....around tensioner and up and over alternator

Nov 30, 2008 | 2000 Dodge Durango

1 Answer

Belt diagram


start at power steering down to ac compressor to crank...around crank to belt adjuster....over fan pulley to alternator up from alt and over both idler pulleys....a 17mm 12point wrench will fit on adjuster to move it

Aug 30, 2008 | 2006 Dodge Sprinter

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...