Question about 1993 Honda Prelude

1 Answer

Clutch no clutch is it clutch cale or master cyinder,how do i check?

Posted by on

  • zcar2 Jul 31, 2008

    I changed the clutch cylinder and air is in the line.



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 359 Answers

On the firewall there will be a small cylinder which will have fluid in it if not you will see a cable coming from there and running to the gearbox

Posted on May 25, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2002 Chevy trail blazer front brakes don't seem to

Um more likely than not you have air in your brake system. I'd suggest bleed your front brakes and make sure your master cyinder cap is tightened also. You may also have a leak somewhere check the reservoir and make sure its not extremely low which would suggest there is a leak somewhere, and check your lines.

Oct 04, 2014 | 2002 Chevrolet TrailBlazer

1 Answer

When at a stop the brakes go down slow to the floor put new master cyl what else can it be

sounds like the brakes need to be bleed, air in the lines can cause this and or a hard peddle

Sep 23, 2012 | 1994 Chevrolet S-10 Blazer

1 Answer

To take off clutch master cylinder man tt zx

just go ahead to replace the cylinder.

Jan 29, 2012 | 1990 Nissan 300ZX

1 Answer

My gears are hard to shift

how does the clutch pedal feel?clutch master cylinder or slave cyinder problem.check the fluid level

Nov 18, 2010 | 2005 Ford Focus

1 Answer

Manual transmisson 1990 camry, shift into 1st or reverse and will not come out unless I shut the car off or double clutch. Clutch pedal seems to have to come of the floor more than normal before the gears...

This is a problem with the clutch, it sounds like a probelm with the hydralics, It could have a leaking slave or master cyinder. If not you will have to replace the clutch

Apr 11, 2010 | 1990 Toyota Corolla

1 Answer

My clucth will not ingage, (92 wrangler). it looks like i'm missing where the hydro clutch connects into the clutch cyinder ?


Thanks for using fixya!

The problem that you are encountering right now has something to do with the primary and secondary clutch cylinder. just buy repair kits for both primary and secondary clutch cylinder. It will only cost you around $20 for both kits

Have a nice day.
- HotRatchet

Jul 28, 2009 | 1992 Jeep Wrangler

2 Answers

Clutch pedal goes down to floor but doesnt come back up when some1 starts engine and i put a bar by clutch level and move it we can select gears then i have change master cylinder but no different can you...

sounds like your clutch plate is sticking, i recommend fitting a new clutch kit, while doing this remember to machine the flywheel or you will still have same problem. if this does not work it might be your clutch cable, replace cale first (cheaper option 1st) then replace the clutch kit.

Jun 04, 2009 | 2003 Mini Cooper

2 Answers

The bite point of my clutch is very low and it is very difficult to change gear. Please help me Thanks. I need to know if I should drive the car (only 60 miles) before I have the clutch replaced as I...

You will not gain anything from "double clutching", The thrust bearing is not fully seated. Normal wear would indicate a high catch point on your pedal. Check the fluid level for the clutch cylinder, check the reservoir cap, look for any moisture under the cap. If it has gotten below the add mark, you may have air, any moisture, flush, refill and bleed. Any of these would create a low pedal...Lube your clutch linkage.
Tip: you can purchase and install aftermarket lubrication kits for
the thrust bearing that will help clutch operations and extend life...
MG's ...keep um on the road!
Good Luck....i hope this helps

May 14, 2009 | 1997 Acura CL

1 Answer

Master cylinder

I just switched my mustang over to dual master cylinder. It wasnt to hard. I bought a kit that had everything i needed. if you want step by step instructions go to click on tech issues at top of page then scroll down to the section for master cyinder conversion

Oct 11, 2008 | 1966 Ford Mustang

Not finding what you are looking for?

Open Questions:

See all 1993 Honda Prelude Questions

1993 Honda Prelude Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides