Question about 1994 Honda Accord

Open Question

Code po116 cam\crank correlation sensor bank1 ..... what repair do i make? runs great most of the time ...but when unexpected the light will come on and the van will run rough until i cut light off with my scanner

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 178 Answers

SOURCE: rough idle stalls at low rpm's

hello first check your idle with the car running foot on brake see were your rpm reading is if your below 500rpm check your label underhood for your curb idle setting second see if theres a adjustment screw you can increase were your gas cable lever rest against your set screw underhood if you feel confident enough remove your iac motor idle air control valve if the bore were the end of the pintle extracts out to close has varnish builup our carbon it will stick creating vacuum leak type senario causing stalling rough idle sometimes even no start conditions good luck

Posted on Sep 18, 2008

  • 373 Answers

SOURCE: 2003 caravan will not start!!!

Hi..
On your problem with the Caravan.

If you Have replaced the Crank and Cam sensors. And the Code Cam/Crank Correlation sensor.
Is found.
Normally this code is present When the Timing belt or Timing Chain, Is out of time 1 or more dents
On the timing due to Skip of the timing belt or Chain.

But don't forget check the connector at the sensors. For any damaged or corrosion on the pins.
Ok.. I hope this help to try diagnostic your car.

Thank you for use fixya.

Posted on Nov 03, 2008

  • 99 Answers

SOURCE: changed spark plugs and timing belt, engine won't start dtc po336

I had this problem before, they way i got round it was to put the sensor just say half way in until the engine sound good on tick over, once that is good make a spacer to keep it like that...or.. like i did buy a new sonsor.

Posted on Dec 01, 2008

  • 366 Answers

SOURCE: 97 Chevy Astro van lugs, like it misses, B4 finally cranking on

crank shaft sen. is easy enough to change.its mounted near timing chain cover,cam sen.is somewhat harder,its in the distributor,id doubt that both are defect

Posted on Mar 10, 2009

  • 1453 Answers

SOURCE: 1991 honda accord - runs rough and stalls on start up.

Did you set the ignition timing after you installed the dist.? If yes, I'd say you got a bad distributor(the one you just put in) since all the codes you're getting are directly for sensors located within the distributor.

Posted on May 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0016 and P0017 check engine pop up after i run for 10 to 15 miles?


the common causes for code P0017 are as follows:
  • A faulty cam or crank sensor
  • The cam or crank circuit is open or shorted
  • The timing belt/chain is out of time
  • The cam or crank tone ring is slipped/broken
  • A problem in the VVT system P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor) God Bless! Hope this helps you.

Mar 08, 2016 | Cars & Trucks

1 Answer

Eng code p0016


P0016 fault is poor crank/cam correlation. In other words the signals the ECU is receiving from the crank and/or cam sensors isn't making any sense and this could be caused by bad cam timing, wiring, connectors or the ECU itself or by faulty sensors but as you have changed these, probably not.

Sep 13, 2015 | Cars & Trucks

3 Answers

What does this code mean


Does the truck run ok? If so may just be bad sensor .it reads the correlation between cam and crank shafts so timing is correct so the camshaft control the valves and crankshaft controlling the pistons don't hit each other

Jul 02, 2014 | 2000 Chevrolet Blazer

1 Answer

P 0016 code


Code 16 is for a problem where the correlation between the crank sensor and the cam sensor for bank one is off. So yes it could be the cam sensor or the timing belt. If compression is normal on all 6 cylinders I would expect to find a bad sensor.

Jan 22, 2014 | Chrysler 300M Cars & Trucks

1 Answer

I have a 2007 jeep patriot. It stalled at stop sign started ran rough. Parked came back drove it home ran u- scan code p0017 replaced crank and cam sensors still runs rough changed plugs were bad. I was...


code p0017 refers to crank/ cam oosition sensor bank 1 sensor B -correlation ===causes --wiring--CKP sensor--CMP sensor--mechanical fault.
It also refers to control modules, cooling fan--no signal===causes -- wiring--ECM.
If it has a timing chain then the the advice that it will not be the chain is good. So I suggest checking out the cam/ crank sensors and wiring

Oct 22, 2013 | 2008 Jeep Patriot

2 Answers

I have a 98 chevy z71 5.7 350 vortec, i have a p1345 code that stays on i clear it and as i restart the truck it comes back on, the truck runs great and has a small delay when starrted.. what can/do i need...


1345 is cam and crank sensor correlation its mainly the cam sensor going out, also the delay start that also trigger a camsensor code they call it excessive crank time check the fuel pressure that is capable of setting a cam code (1345) If fuel pressure is good (55-60 psi) expect to replace the camsensor you might as well do the crank sensor heres a nightmare on this code it can set if the distributor is off one tooth and yes these distributor have high failure rate

Jun 08, 2011 | 1998 Chevrolet K1500

1 Answer

I have 2008 Dodge Caliber and the engine light came on with codes P0017 Crank Shaft Position Cam Shaft Position Correlation - Bank 1 Sensor B can you tell me what this means as i cannot afford to...


Sounds like your crank sensor or cam sensor is malfunctioning. Their positions are not correlating which means they are not in perfect alignment according to the computer. I don't think the parts are very expensive and probably not that hard to replace. I replaced both on my 99 Ford Explorer, and I don't recall it that difficult. Anyway, hope this helps.

Mar 17, 2011 | Dodge Caliber Cars & Trucks

2 Answers

What is code P1345?


I had the p1345 on my 2002 Silverado this week. The code means Crankshaft/camshaft position correlation. In other words the cam is not where it is supposed to be in reference to the crank. It could be the Cam position sensor, the crank position sensor , the gear on the distributor or the timing chain. The quickest and cheapest check is the distributor gear which is what mine was. It's quite common. The gear is about $60 and can be replaced in less than an hour with the right experience. The engine won't usually run if it's the crank sensor and the cam sensor is a little more.

May 27, 2010 | 2002 GMC Sierra

2 Answers

Can you tell me what codes 54 and 21 are on a 1995 caravan 3.0 please?


Hello..
Code 21: Is an oxygen sensor Code 54: Is a crank positioning sensor.
Hope this helps!

Dec 06, 2009 | 1995 Dodge Caravan

1 Answer

2003 caravan will not start!!!


Hi..
On your problem with the Caravan.

If you Have replaced the Crank and Cam sensors. And the Code Cam/Crank Correlation sensor.
Is found.
Normally this code is present When the Timing belt or Timing Chain, Is out of time 1 or more dents
On the timing due to Skip of the timing belt or Chain.

But don't forget check the connector at the sensors. For any damaged or corrosion on the pins.
Ok.. I hope this help to try diagnostic your car.

Thank you for use fixya.

Nov 03, 2008 | 2003 Dodge Caravan

Not finding what you are looking for?
1994 Honda Accord Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...