Question about 1985 Toyota Celica Supra

1 Answer

Where is the knock sensor located 1985 supra - 1985 Toyota Celica Supra

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 14,036 Answers

ITS UNDER INTAKE MANIFOLD OR BELOW THE INTAKE MANIFOLD ON SIDE OF THE CYLINDER BLOCK.

Posted on Sep 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code 52 knock sensor, 88 toyota supra 7mgte. I replaced the wires 8 inches, fixed the ground, got a new sensor and tested both, its still throwing the code, it runs so hard especially because the timi


if you have done all the obvious repairs then you may have an issue with the pcm or wiring to it.. the knock sensor isnt crucial in driving as its only purpose is to get the best performance possible without the ping and knock created by to little or to much timing advancement done by the pcm..you can still drive it its just annoying seeing the light on.. if car does not run right then you have another issue like a miss in the engine.. check plugs wires coils

Jul 14, 2012 | 1988 Toyota Supra

2 Answers

I have a 95 oldsmobile 98 regency elite I cant find where the knock sensor goes I have a haynes manual but where it shows it wont go


Well, for starters, your problem got posted under 1985 Oldsmobile 98 - then you said it was a 95 Oldsmobile 98 Regency Elite (HUGE difference between 85 and 95)...then it would be REALLY nice to know which engine we are talking about.

I'll just go with what you said last: 1995 Oldsmobile Regency Elite (Two engine possibilities)

If you have the 3.8L Supercharged engine (VIN CODE "1") it is on the left side of the engine near the oil filter.

If you have the non-supercharged 3.8L (VIN CODE "K") there are TWO of them. One is near the oil filter and the other one is in about the same location on the other side of the engine block.

Please also note that MOST fault codes for knock sensors are not caused by the knock sensors themselves. (they do fail, but it is very rare.) Usually there is either a wiring problem to the knock sensor, or the engine has internal problems causing a "knocking" or "ticking" noise which causes the engine computer to "think" that there is a problem with pre-detonation causing an "ignition ping". The code sets when the computer has retarded the ignition timing as far as it can and the "knock" or "ping" does not go away....usually it doesn't go away because it is not caused by ignition timing. The knock sensor is just doing its job and reporting the knock. It does not know the difference between a knock caused by ignition and a knock caused by internal engine problems.

Jun 28, 2011 | 1985 Oldsmobile 98

1 Answer

Where is the fuel filter located on a 85 celica supra?


LOOK UNDER HOOD FOR INLINE FUEL FILTER THAT GOES TO CARBURETOR OR FUEL INJECTORS.

Dec 17, 2010 | 1985 Toyota Celica Supra

2 Answers

Ebrake light stays on 85 celica supra


you need to fill your brake fluid resevoir to the fill line and your brake light on the dash will go away

Feb 16, 2009 | 1985 Toyota Celica Supra

2 Answers

Knock sensor location


it is screwed in the engine block on the right side

Dec 09, 2008 | 1991 Toyota Supra

1 Answer

Knock sensor location


under the intake manifold, if it is turbo there should be two of them. please note that I have seen many of these that set knock sensor codes and the problem was usually in the wiring. wire will ohm ok but the problem is faulty shielding that allows other voltages to leak into the circuit. easiest fix is to buy some shielded microphone wire from radio shack and run a new wire from the sensor to the ecu.

Dec 09, 2008 | 1987 Toyota Supra

Not finding what you are looking for?
1985 Toyota Celica Supra Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...