Question about 1984 Chevrolet C1500

1 Answer

How do you replace the rear engine seal on a 84 c1500 350

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

You will have determine if its a 1piece seal or 2. If its a 1piece rear main you will have to remove transmisson to install. If its a 2piece you will have to remove the oil pan to replace.Hope this helps
D.

Posted on Sep 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the big end torque settings for a Daewoo matiz 800


main bearing cap bolts 36-39 ft. lbs. oil pan bolts 51-69 in. lbs. oil pan nuts 43-60 in. lbs. oil pan drain plug 33 ft. lbs. oil pump cover bolts 72-84 in. lbs. oil pump relief valve plug 29-36 ft. lbs. oil pump sprocket nut 25-28 ft. lbs. Rear oil seal retainer bolts 84-108 in. lbs. rocker arm shaft bolts 14-15 ft. lbs. rod bearing cap nuts 23-25 ft. lbs. silent shaft sprocket nut 22-28 ft. lbs. spark plugs 15-21 ft. lbs. thermostat housing-to-Engine bolts 86-114 in. lbs. timing belt tensioner bolt 32-40 ft. lbs. valve cover bolts 43-61 in. lbs.

Nov 29, 2014 | 1999 Daewoo Matiz

2 Answers

My drivers side rear tire locked up while driving in my 84 Nissan Datsun pulsar NC what's wrong


'84 ...*lotsa* miles on it ....like 450K plus if you drive the "normal" 15K/year. First, and most likely, thing that comes to mind is the wheel bearing has seized. Since this is a front wheel drive car, there are sealed roller bearings for the rear wheel hubs. At 450K on the odometer there are *lots* of components that have reached or exceeded their normal service life. I would suspect the left rear sealed wheel bearing is one of them ...followed closely by the right rear wheel bearing. If it's the bearing? Get them both done.

May 01, 2014 | Cars & Trucks

1 Answer

Cost replace rear main seal toyota camry


Four cylinder or V-6.

Both engines will require the removal of the timing belt to service the front crank seal. Both engines will also require the removal of the transmission to replace the rear main seal

either way way you would be looking at 3-4 hours for the front seal and 5 to 6 hours for the rear seal.

Apr 10, 2014 | 1997 Toyota Camry

1 Answer

Rear seal leaking on 2007 ford escape


In order to replace the rear main seal you will need some auto repair tools and experience . this is a big job , the transmission must be removed to replace this seal, also make sure that the seal is the leak,

oil always flows down, a leak on the top of the engine will flow down and drip at the center rear and look like a rear main seal , make sure that is the leak!!.

Depending on what engine you have and if it has 4 wheel drive the time for a shop to do is from 7 to 10 hours depending on engine size and 4wd,

Oct 21, 2012 | 2007 Ford Escape

2 Answers

I have a heavy oil leak on my 84 Jimmy GMC. I've replaced the rear main seal, valve cover gaskets and oil pan gaskets. What else could it be?


Have you washed down the engine, and ran for a few days to see if leak still persists, is it a flowing leak or slow leak, and are you sure that it is engine oil ????

Mar 28, 2011 | GMC Jimmy Cars & Trucks

1 Answer

Rear main seal replacment


If you have a shop you need to pull the engine to replace the rear main seal. There is a possibility of a two part seal. If you have a two part seal drop the oil pan and pull the rear main engine cap off and then replace the seal. You may need specialized tools.

Dec 03, 2010 | 1995 GMC Sierra C1500

1 Answer

Rear barring an seal replaced


I'm not sure if this is the right part of your car but, are you talking about the rear seal on the engine for the crankshaft?

If so:

Rear Main Oil Seal REMOVAL & INSTALLATION Fig. 1: Rear main seal installation for the 2.3L and 2.5L engines 85553306.gif
Fig. 2: Removing the rear main seal 85553307.gif
Fig. 3: Installing the rear main seal on the 2.9L engines 85553308.gif
If the crankshaft rear oil seal replacement is the only operation being performed, it can be done in the vehicle as detailed in the following procedure. If the oil seal is being replaced in conjunction with a rear main bearing replacement, the engine must be removed from the vehicle and installed on a work stand.
  1. Remove the starter.
  2. Remove the transmission from the vehicle, following the procedures in Section 7.
  3. On a manual shift transmission, remove the pressure plate and cover assembly and the clutch disc following the procedure in Section 7.
  4. Remove the flywheel attaching bolts and remove the flywheel and engine rear cover plate.
  5. Use an awl to punch two holes in the crankshaft rear oil seal. Punch the holes on opposite sides of the crankshaft and just above the bearing cap to cylinder block split line. Install a sheet metal screw in each hole. Use two large screwdrivers or small pry bars and pry against both screws at the same time to remove the crankshaft rear oil seal. It may be necessary to place small blocks of wood against the cylinder block to provide a fulcrum point for the pry bars. Use caution throughout this procedure to avoid scratching or otherwise damaging the crankshaft oil seal surface. To install:
  6. Clean the oil seal recess in the cylinder block and main bearing cap.
  7. Clean, inspect and polish the rear oil seal rubbing surface on the crankshaft. Coat a new oil seal and the crankshaft with a light film of engine oil. Start the seal in the recess with the seal lip facing forward and install it with a seal driver. Keep the tool, T82L-6701-A (4-cyl. engines) or T72C-6165 (6-cyl. engine) straight with the centerline of the crankshaft and install the seal until the tool contacts the cylinder block surface. Remove the tool and inspect the seal to be sure it was not damaged during installation.
  8. Install the engine rear cover plate. Position the flywheel on the crankshaft flange. Coat the threads of the flywheel attaching bolts with oil-resistant sealer and install the bolts. Tighten the bolts in sequence across from each other to the specifications listed in the torque chart in this section.
  9. On a manual shift transmission, install the clutch disc and the pressure plate assembly following the procedure in Section 7.
  10. Install the transmission, following the procedure in Section 7.
prev.gif next.gif

Oct 07, 2010 | 1994 Ford Explorer Limited

1 Answer

Rear main seal leaks..does this affect transmission??


A leaking rear main seal will not cause your transmission to leak.

The transmission has its own seal and should not leak because of the engine rear main seal.

Due to the labor involved in replacing the rear main seal on the engine, it is best if you replace the front transmission seal at the same time if possible.

Installation varies on different vehicles but the principles are the same.

Apr 15, 2009 | 1997 Oldsmobile Regency

1 Answer

2005 Tucson


camshaft sprocket bolt 58-72 ft. lbs. crankshaft pulley bolts 108-132 ft. lbs. crankshaft pulley center bolt 80-94 ft. lbs. cylinder head bolts cold engine 65-72 ft. lbs. warm engine 73-80 ft. lbs. cylinder head rear cover bolts 69-86 in. lbs. flywheel/Driveplate bolts 94-101 ft. lbs. intake/Exhaust manifold nuts/Bolts 11-14 ft. lbs. jet valves 13-16 ft. lbs. main bearing cap bolts 36-39 ft. lbs. oil pan bolts 51-69 in. lbs. oil pan nuts 43-60 in. lbs. oil pan drain plug 33 ft. lbs. oil pump cover bolts 72-84 in. lbs. oil pump relief valve plug 29-36 ft. lbs. oil pump sprocket nut 25-28 ft. lbs. Rear oil seal retainer bolts 84-108 in. lbs. rocker arm shaft bolts 14-15 ft. lbs. rod bearing cap nuts 23-25 ft. lbs. silent shaft sprocket nut 22-28 ft. lbs. spark plugs 15-21 ft. lbs. thermostat housing-to-Engine bolts 86-114 in. lbs. timing belt tensioner bolt 32-40 ft. lbs. valve cover bolts 43-61 in. lbs. water pump-to-Engine bolts alternator brace bolt 14-20 ft. lbs. all others 9-11 ft. lbs. water pump pulley bolts 72-84 in. lbs.

Sep 08, 2008 | 2005 Hyundai Tucson

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...