Question about 2003 Nissan Altima

1 Answer

Cam position sensor code comes repeatedly even after putting in new sensor and new ecm

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 863 Answers

Take it to the dealership and have them deal with it, cause this is fixed for free under the recall program they got.

Posted on Oct 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

07 mini change the cam sensor and timing code keep come back on saying timing to far advance


possibly not the sensor but the hydraulic adjuster that controls the cam timing
the cam sensor reports the cam position in relation to engine rpms and the ECM adjusts the cam position by the hydraulic servo / solenoid to the preset cam position for that rpms
I suspect that the problem will be in that servo / solenoid

Aug 20, 2016 | Mini Cars & Trucks

2 Answers

If both cam/crank position sensors have ONLY been unbolted and replaced with new sensors, do they require synchronization?


Sensors do not need to be recalibrated , the ecm should have the codes cleared . Then turn the ignition system on with data reader hooked up to see if sensors repaired the fault code.

Oct 11, 2015 | 2003 Ford Mustang

1 Answer

Why dose car not start


code p1362 refers to camshaft position sensor (CMP) ---no signal==causes wiring--CMP sensor--ECM programming--ECM
First point -cheap sensors are a waste of time and money as they have to be made with a pre-set range suitable to the ECM in your car. next point --when fitting cam/crank position sensors you have to ensure the correct air gap is maintained . third point ---because it is not set to your CPU program then it is advisable to use a scanner tool to reprogram the CPU to read the sensors fitted. I would advise a change of mechanic as it appears that the advice you are getting is not exactly accurate.

Jul 15, 2014 | 1991 Honda Civic

1 Answer

I have code P1340 igniter circuit on a toyota yaris


Error Code:P1340
Description: Camshaft Position Sensor B Circuit Malfunction
Solution:
-
Delete codes
- Check the connector and wires attached to the cam shaft position sensor.
- Cam shaft position sensor defective. (Replace with good known one).
- Wiring harness.
- ECM.

Mar 16, 2014 | 2004 Toyota Yaris 1.0

1 Answer

New ECM put in


if you put in a new ECM and nothing has changed.... it wasn't the ECM in the first place. Look at the ignition coils, the cam position sensor and the ignition switch

Jan 09, 2014 | 2000 Buick Park Avenue

1 Answer

Code p0370 resolution to higth


code po370 refers to timing reference, high resolution signal--malfunction====causes -- wiring---crank position sensor---RPM (tacho) --cam shaft position sensor---ECM . Have the ECM professionally checked along with the 2 sensors

Dec 20, 2013 | Cars & Trucks

1 Answer

My dodge caravan 4 cylinder engine has trouble codes 0016,0113,0700,0562


code p0016refers to the crankshaft /cam shaft position sensor bank 1 sensor A-- correlation===causes---Wiring CKP sensor--CMP sensor--mechanical fault Check timing belt is not broken
code po113 refers to intake air temp (IAT) sensor--circuit malfunction===causes ---wiring open circuit/short to positive--wiring short to ground---ground wire defective IAT sensor---ECM
code mp0700 refers to transmission control system/MIL-malfunction===causes--wiring ---TCM
code po562 refers to system voltage low==causes---wiring poor connections---battery---alternator or it also refers to ECM power relay control--circuit open===causes ---wiring--ECM ---relay. For this one check the battery terminals and posts are shiny clean and tight . Have a load test done on the battery to check for faulty cell. check condition of alternator drive belt and check alternator out put.

Sep 27, 2013 | 2003 Dodge Caravan

1 Answer

2001 jetta vr6 cranks but won't start have fuel and spark replaced camshaft sensor, new plugs valve cover gasket got code of PO343 and PO740


code po740 refers to torque converter clutch(TCC) solenoid-circuit malfunction==causes --wiring--TCC solenoid-ECM/TCM
code p0343 refers to cam shaft position sensor(CMP) A bank1-high input.==causes --wiring short to positive--CMP sensor---ECM. check which cam sensor you replaced and check the wiring connectors. use a code reader to reset the cpu when finished

Sep 06, 2013 | Volkswagen Jetta Cars & Trucks

1 Answer

What do P0016 and P0017 codes mean on a 2010 Equinox?


P0016 is the crankshaft position (CKP) to intake camshaft position correlation; P0017 is the exhaust camshaft position correlation.

P0016 sets when 'The ECM detects 8 of the last 10 cam sensor pulses occur during the incorrect crankshaft position."
P0017 sets when 'The ECM detects 25 out of the last 35 cam revolutions occur with 2 cam sensor pulses outside the CKP window."

Basically, you're getting pulses when they shouldn't happen, from both cam sensors, or the CKP is generating incorrect window info. Since the CKP is the common element, it's probably the culprit.

The cam position sensors are at the back of the head, one on each side corner. The CKP is under the oil filter housing, above the starter. To replace the CKP, you're supposed to remove the intake manifold and starter.
__________________

Dec 30, 2012 | 2007 Chevrolet Equinox LS New Cars

Not finding what you are looking for?
2003 Nissan Altima Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...