Question about 1997 Chevrolet Cavalier

1 Answer

I drive a 97 cavalier (stick shift)....today i pressed the clutch down and it went straight to the floor. i put clutch fluid in and it leaked out. how much am i looking to pay to have this promblem fixed

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 474 Answers

More than ar is worth

Posted on Sep 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 dodge ram 1500 with the 3.7L V6 5 speed manual. The truck drives and shifts fine but after driving for a while it won't be able to shift into or out of any gear.


the reason for hard shifting and selection when running is that the clutch shaft ( input shaft) is still turning even though the clutch pressure plate is released
it can be from oil/grease on the fly wheel /pressure plate face causing it to stick when hot
it may be from sticking clutch plate on the splines binding when hot
or it could be a dry spigot bush or failed bearing in the end of the crankshaft that positions the clutch shaft
check the pedal height adjustment and the position it is from the floor when starting to engage
It may be adjustment under the dash

May 18, 2015 | 2004 Dodge Ram 1500

2 Answers

Why is Clutch pedal is going straight to the floor?


you have a leak on your clutch master you need to replace probably the leak started small and now its worst

Jun 09, 2014 | 1994 Mazda 323

2 Answers

Clutch pedal sticks on floor


on the bottom of the clutch housing there is a bleed nipple, like on the brakes, if you have pumped the clutch with out enough fluid in the brake receiver container you would of put air in the clutch system, you need to keep it topped up all the time so its at max. and bleed the clutch, you will need to lift the clutch pedal by hand up and down a few times to get the air out, its not assisted like the brakes so it will take a good few pumps and tightening the nippel when it feels pressure.

Jun 03, 2017 | 2004 Chevrolet Cavalier

1 Answer

97 jeep Cherokee clutch will not depress to start the engine


Now you need to bleed the clutch at the clutch slave cylinder down on the transmission to restore the clutch.
Put a wrench on the bleed valve and open it, then lightly close it. Now have someone pump the clutch a couple of times to build pressure. Then while the clutch pedal is slowly pressed down open the bleed valve, then close valve as pedal gets to floor. Repeat this bleed process until a steady stream of brake fluid comes out the bleed valve. Then you should have a good clutch again.

Dec 20, 2012 | 1997 Jeep Cherokee

2 Answers

Clutch pedal sticks to the floor; the brake reservoir was low


I believe your pressure plate is broken and at a minimum will have to be replaced along with the clutch disk.

Jul 04, 2010 | 2006 Ford Fusion

1 Answer

My clutch pedal went to the floor in my 2003 chevy cavalier


check the clutch fluid level. if its empty, you have a leak, and you have air in the system. if there is no leak, and the fluid level is full, the problem lies in either the clutch master cylinder or slave cylinder.

Mar 23, 2010 | 2003 Chevrolet Cavalier

2 Answers

1989 jeep wrangler wont shift gear and clutch gone loose


Get the clutch slave cylinder and master cylinder looked at.One of the 2 has failed.If the pedal goes to the floor or is very loose,this is very likely the cause.Not an expensive fix.Hope this helps

Jan 10, 2010 | 1989 Jeep Wrangler

1 Answer

I have a 1989 jeep wrangler. yesterday, after the stick shift felt stiff to shift, the clutch felt suddenly loose. Today, the stick shift stopped moving completely while i was driving. Finally, I was able...


Sounds like you are having a clutch problem. The sudden looseness in the clutch pedal indicates a problem with either the hydralic system, (slave or master or line) leaking or clutch pressure plate going out. Check your clutch fluid resevoir first, if low look for a leak under the vehicle, have a friend push the clutch and get underneath to find leak.

Jan 10, 2010 | 1989 Jeep Wrangler

1 Answer

1979 Datsun 280zx clutch problem


Well, Your are going to have to put a few bucks into a new clutch , disc, pressue plate.
A local transmission shop should be able to help you out.

Mar 15, 2009 | 1997 Chevrolet Cavalier

Not finding what you are looking for?
1997 Chevrolet Cavalier Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...