Question about 2000 Chevrolet Camaro

1 Answer

How to check and replace full throttle indicator mechanism, believed to be the problem.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Chevrolet Expert
  • 124 Answers

Before you jump to that check and see if there are any codes. Most likely the full throttle is not the problem. Have it checked on a scope before you start replacing parts.

Posted on Mar 07, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car is starting very well but when i push the gas pedal down it doesn't make the car accelerate


I am assuming that this vehicle has an electronic throttle control rather than an actual throttle cable.

You will need to get access to a scanner and check the code to determine whether you have a defective throttle position indicator at the pedal itself, wiring problems between the pedal and the PCM and the actuator to the throttle itself. You will also need access to a manual, and a good digital volt ohm meter.

If the vehicle has a mechanical braided cable on the side of the throttle, then you need to check for a broken throttle cable and replace if necessary.

Nov 25, 2015 | 2005 Nissan Altima

1 Answer

2009 Ford Mustang has no throttle response at all why?


1.Check wiring. 2checkair fow meter or fow meter also spark plugs

Dec 01, 2013 | Ford Mustang Cars & Trucks

1 Answer

Izusu rodeo woulnt start. Mechanic replace starter. Now it is running wide open. It fine while driving but when coming to a stop it just revs super high. Any thoughts?


Check that the throttle cable has been correctly installed and is not jammed at full throttle . Run fault codes to check for throttle position sensor fault. Reset the CPU using a code reader as by disconnecting the batter to replace the starter the CPU program may have become corrupted and needs resettiing

Oct 26, 2013 | Isuzu Rodeo Cars & Trucks

1 Answer

2009 focus idles rough when it rains or after going to car wash. The code indicates throttle body sensor, but mechanic says he doesn't think that is the problem.


I don't think it is either--- that is high & dry

Check the abs connector next to module or
something closer to the ground for water intrusion

Nov 29, 2012 | Cars & Trucks

1 Answer

Rough idle on 2004 Grand Cherokee Overland 4.7 HO with 150,000 miles on it. My mechanic ruled out coil and spark plugs already. No check engines lights and otherwise runs and starts fine. So this Monday he...


CHECK OR REPLACE ALL VACUUM HOSES.REPLACE AIR FILTER,REPLACE FUEL FILTER,CLEAN FUEL INJECTORS WITH A CAN OF SEAFOAM TO 3/4 TO FULL TANK OF GAS.CLEAN THE THROTTLE BODY THROTTLE PLATE.SPRAY CARBURETOR CLEANER INTO THROTTLE BODY BREAK CARBON BUILD UP AROUND THROTTLE PLATE AND SPRAY CARB CLEANER AROUND THROTTLE BODY SHAFT AREA REMOVE CARBON BUILD UP TO PREVENT SHAFT FROM BINDIND.BECAREFUL NOT TO GET CARBURETOR CLEANER IN THE IDLE AIR CONTROL VALVE AND OTHER ELECTRICAL PARTS.REPLACE ALL VACUUM HOSES ON THE INTAKE MANIFOLD AND REPLACE PCV.

May 08, 2011 | 2004 Jeep Grand Cherokee

2 Answers

We put a tester on my 1999 blazer and it came up 1 code P0300???? gettin a seconed opion


p0300 is a random misfire, which usually indicates almost anything-generally a good tune up will fix it, like new wires, plugs, clean the throttle body, dist cap/rotor, check charging system, check fuel pressure, replace fuel filter...it is random (usually fuel) but a good going-over by a decent and honest mechanic will fix it.

Apr 21, 2011 | Chevrolet Blazer Cars & Trucks

3 Answers

Full throttle all the time


We actually have a TSB for the drive by wire systems that calls for both a TPS sensor/actuator replacement but it's required that you also do a PCM reflash at the same time. If you put in the new updated part without doing your reflash then you've found your problem.

Take it to the dealer and get the reflash done.

Nov 23, 2009 | 2004 Hyundai Tiburon

1 Answer

I have a 2000 Audi TT front wheel drive. Within the last two months the engine has developed a lot of spatial vibration under load. I can feel it in the steering wheel, pedal and the whole front end. I...


check for deformed tyres ?? this is the most obvious cause,i may be old dinasaur who gets lost with sensors and electronic stuff but after 40 yrs somethings never change

Sep 15, 2009 | 2000 Audi TT

Not finding what you are looking for?
2000 Chevrolet Camaro Logo

Related Topics:

348 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...