Wehad this problemb when ou mecanic changed the roter cap he bumped the timeing so it was off just a little then of course wanted to charge to fix it we just turned or nudged the poins module under the cap alittle and it idles now. not perfect but better
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
replace the TPS ,@ throttlebody, throttle position sensor, either needs replaced, or the 2 bolts that hold it on came loose, sensor needs to be turned a little , to increase throttle, then retighten bolts. should also tighten the throttlebody bolts to intake manifold,
Can be several things. May just need a tune up:spark plugs, wires, rotor cap and button, fuel filter, air filter. It may also need a timing adjustment, Idle Air Control (IAC) valve, or throttle position sensor. Do the tune-up first and see what it does.
2 airflow sensor out of operating range 3 coolant temp sensor out of operating range 4 oxy sensor indicates full rich 5 throttle potentiometer/airflow sensor... (low throttle pot signal with high airflow sensor signal) 6 throttle pot/airflow sensor...... (high throttle pot signal with low airflow sensor signal) 7 throttle pot...idle fuel adjustment failure(idle speed??) 8 intake air temp sensor...open or shorted circuit to sensor 11 Throttle pot at idle: Throttle pot idle trim out of normal range 12 Airflow meter: MAF signal out of range 14 Coolant thermistor: Resistance out of range or static during engine warm up 16 Air thermistor: Resistance out of range 17 Throttle pot: Out of range 18 Throttle pot/Airflow: Low throttle pot signal at high airflow 19 Throttle pot/Airflow: High throttle pot signal at low airflow 22 Fuel pump drive: ECU output to fuel pump relay 23 Fuel supply: Engine running too rich 24 Ignition Drive: ECU output to ignition Amp 26 Air leak: Engine running too lean 29 ECU self check 33 Injector Drive: ECU output to injectors 34 Injector: Looks for Injector dribble 37 EGR Drive: ECU output to EGR switching valve 39 EGR check sensor: EGR not working (normally pipe blocked) 44 Lambda (O2) sensor: Poor mixture control rich or weak (or misfire) 46 Idle speed Control valve: ECU output to Coil AB 47 Idle speed Control valve: ECU output to Coil CD 48 Idle Speed Control Valve: Stepper motor grossly out of position 66 Air pump: ECU output to air pump relay 68 Road speed sensor: Seen speed < 5km/h at high engine airflow 69 Drive/Neutral switch: Seen cranking in "D" or high airflow in "N" 89 Purge Valve drive: ECU output to purge valve this is all I could find
sounds real easy either a bad idle air control solenoid or more likley a blown throttle body gasket. to test fro a blown gasket, with engine running and cool spray carb cleaner or brake cleaner around base of tb were it bolts to intake. when it hits the bad area, should idle down and be normal for a second or 2. iac is possible,try this first since its so common and let me know
Have a fuel pressure test done, that will show a weak fuel pump, or bad fuel pressue regulator, also have the throttle position sensor checked.
Could be the idle air control valve,
could be the fuel bypass valve.
Without checking and testing, it's hard to pin point the problem.
check the wiring to the airflow sensor located on the hose that goes to the throttle body.check the vacuum lines,and the idle air controller,the throttle position sensor.and the coolant temperature sensor.check the egr valve is not stuck,the catalytic converter plugged if you have a sulfur smell,and the fuel pressure,and the fuel filter.there is also an ignition module cap and rotor.and maybe a bad spark plug if it is idling rough