Question about 2004 Chevrolet Cavalier

1 Answer

How do I replace the signal switch assembly on my 2004 Chevy Cavalier?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,565 Answers

Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF , unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.

  1. Disconnect the negative battery cable.
  2. Remove the steering column trim covers.
  3. Remove the retaining screws from the multifunction switch.

    How do I replace the signal switch assembly on my - 0996b43f802054ac.jpg enlarHow do I replace the signal switch assembly on my - enlarge_tooltip.gifenlarge_tooltip.gif

    Fig. Remove the multifunction switch (2) from the steering column

  4. Remove the multifunction switch from the steering column.
  5. Disconnect the electrical connectors from the multifunction switch.

To install:
  1. Connect the electrical connectors to the multifunction switch.
  2. Install the multifunction switch to the steering column while depressing the spring loaded horn pin.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the retaining screws to the multifunction switch and tighten the screws to 36 lb inches (4 Nm).
  4. Install the steering column trim covers.
  5. Connect the negative battery cable.
  6. Ensure that the multifunction switch functions properly.

Posted on Sep 27, 2010

  • cheap repair Sep 27, 2010

    this can be seen at autozone.com

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace turn signal cancel device in steering column of 2001 Cavalier


remove the steering wheel and then remove the indicator switch assembly

Jan 20, 2017 | 2001 Chevrolet Cavalier

1 Answer

How to replace alternator on 2004 Chevy Cavalier LS


go to auto zone and get a repair book on your car it will help you in long run.

Jan 13, 2014 | 2004 Chevrolet Cavalier

1 Answer

How to change the turn signal baulb in the rear light on my 2004 chevy cav


Hi, I am not familar with the 2004 Caviler; however, I can give you some suggestions on how to get this lanp/bulb replaced. First, look in the trunk. With some cars, you can access these lamps from the inside of the trunk. If access to these rear lamps this is not possible through the trunk, then look at the actual light assembly from the outside. Some cars will allow access to therse rear lampsfrom the outside by removing a few screws and then pulling out the entire light assembly. Good Luck!

Jan 09, 2011 | 2004 Chevrolet Cavalier

1 Answer

How do i replace a turn signal switch in a 2003 Chevy Cavalier


Your going to need to remove the steering wheel and the steering column cover,then you can access the screws holding the "multi function switch",which is the new name for the turn signal switch ,since it does more now.

Dec 19, 2009 | 2000 Chevrolet Cavalier

1 Answer

How do I replace the right front turn signal bulb on a 1999 Chevy Cavalier?


Remove the splash shield that fits across the top (under the hood). You need to carefully pry the six bolt-style plastic clips off that hold it.
The signal lamp assembly is removed by releasing a clip which is located between the headlamp assembly and signal lamp assembly. There is a slot in the top to insert a screwdriver. Push down on the clip and the signal assembly should slide right out.

Nov 16, 2009 | 1999 Chevrolet Cavalier

1 Answer

1998 Cavalier rear turn signal doesn't work


The turn signal switches are known to go bad, try to use the turn signal switch and jiggle the lever after clicking to the left turn. Replace signal switch assembly.

Jul 19, 2009 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
2004 Chevrolet Cavalier Logo

696 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...