Question about Buick Rendezvous

2 Answers

I relaced all brake pads on 2003 buick bleed brakes very little air my brake peddle still spungy and anti brake light stays on

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 4,536 Answers

Did u only du master cylinder--may shud du it at each wheel--also mite need to clear lite by disconnec battery or scanning

Posted on Sep 27, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 672 Answers

You must re-bleed the system properly, especially the back brakes. Bring your vehicle to a local autozone to reset the ABS light or check for an ABS fault code and post it on fixya!!

Posted on Sep 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake pedal goes to floor when engine running but is fine when engine off


bleed the brakes again starting at the longest line at the rear and work forward . The indication is still air in the lines.

Feb 05, 2015 | 2002 Saturn SC

1 Answer

My 2002 buick rendevouz brake light stays on after i get it upto 30 miles per hour


you will need to change the switch on the brake peddle. sits behind the cover. this can happen in an emergency and you also push peddle to the side wile ding it.

Mar 16, 2014 | 2003 Buick LeSabre

1 Answer

How to bleed the brakes alone on a 00 maxima


The pedal should not feel that way if you just changed the pads, you must have another issue like a master cylinder

May 30, 2012 | 2000 Nissan Maxima

1 Answer

97 brake light chime


Several possibilities here, First, if your parking brake lever is even slightly engaged your brake light will be on. so check the cable and switch to make sure it is not this. Second is the brake pressure switch on the master cylinder, the switch could be bad or your lines may need bleeding. and last, unless there is a separate light for it you anti-lock brakes could have an issue, which I would recommend a qualified mech look at that.

Nov 09, 2011 | 1997 Buick Park Avenue

1 Answer

Low brake fluid light, brake light, and trac light are all on. Put new brake pads on yesterday and brake fluid is full. What do i do?


DID AIR ENTERED THE SYSTEM IF SO NEED TO BLEED AIR BACK OUT
IF AIR IS IN SYSTEM PEDAL WILL BE VERY LOW (CLOSE TO FLOOR)
VERY LITTLE RESISTANCE

Apr 27, 2011 | 2003 Chevrolet Monte Carlo

2 Answers

No brakes I think the booster was going out because my peddle got soft but would still stop me then i changed my brake pads shortly after the brakes completly went out and can now only stop with the...


The problem is not the booster, the job of the booster is to make braking easier. If the booster went out the brakes would be hard to press.
Your soft pedal is likely due to air in the brake lines. Bleed the brakes and go from there.

Dec 13, 2010 | 1992 Buick Park Avenue

1 Answer

2003 rav 4, just replaced front calipers and pads, after bleeding the line,peddle was spongie, bled all four lines, peddle still spongie, do I need the engine running to properly bleed the lines, and since...


I would bleed the rears too especially if the brake fluid reservoir drained empty. Also you may need to drive the vehicle to seat the brake pads. Check and see how the pedal feels initially before you road test to make sure you don't need to pump the brakes in order to stop. if you do then re bleed all four wheels.If you don't have to pump the pedal and it just feels spongy then try going around the block a few times and see if the pedal stiffens up after the pads have seated.

Oct 11, 2010 | 2003 Toyota RAV4

1 Answer

I have a maxima 1993 I change brake pump and booster and front pads and rear choose.. And the brake pedal keeps going down a little by little. It's like if was loosing some presure.. Some where.. Not so...


if you are losing peddle and their are no leaks in the system, meaning you have to keep adding fluid then you have an internal leak in the master cylinder . if it was just air in the lines, not bleed right you would have a spongey peddle meaning it would stop but the peddle would feel like rubber, or it would pull to one side

Oct 01, 2010 | 1993 Nissan Maxima

1 Answer

How much is a brake press module for a 2003 buick century'


The brake pressure modulator can be between $900, to $1500 depending on the exact options and braking system. Good Luck

May 06, 2009 | 2007 Buick Century

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

290 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...