Question about Toyota Avalon

2 Answers

97 6 cylender avalon that is slow to start and to keep it running at a stop, have to hold brake and accellerator.

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 672 Answers

Do you have a check engine light "on"?? possible issues; crank sensor, cam sensor, timing, IAC valve (idle air control valve)

Posted on Sep 27, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,565 Answers

Clean out your throttle bore and idle air controller and pcv valve with spray carb cleaner.

Posted on Sep 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car has no power seems to be running on 1 cylender and speedo stops at the same time


Sadly Peter when noone but you knows what vehicle you have we can not possibly assist you

May 31, 2016 | Cars & Trucks

1 Answer

Volkswagen problems


might need a tune up, new airfilter etc .

Jan 25, 2014 | Cars & Trucks

1 Answer

How do i know if the master cylender is bad


You run a line clamp test. All you need is 4 clamp tools to block off all brake hoses with light pressure. Push on brake peddle if it's hard back off and push slow and light. If stays hard master cylinder is good. Hold pressure and have someone remove. The clamps

Feb 01, 2012 | Cars & Trucks

2 Answers

How do I bleed the brakes?


I will explain it to you the best way i know how..take the cap off of the master cylender, make sure its full of fluid, leave cap off, get a partner. when you bleed brakes you always start at the wheel farthest away from the master cylender and work your way to it, so start at the rear passengers wheel, have your partner pump the brake pedal 12 or so times, and hold pressure against it ( TELL THEM NOT TO LET UP, UNTIL YOU TELL THEM) crack the bleed plug, let air/fluid out, re snug the plus.( now they can let off.. if they let off of the pedal before the bleeder is tight, it will pull air in the system, and you will hafta start all over again.) Do this a few times, until you get a steady flow of fluid, with no air bubbles. After this one is bled, top back off the master cylender, then go to the back Drivers wheel, do process over again, between every wheel top off master cylender. then go to passengers front, and then finally drivers front... hope i explained this good enough for you to understand.. and if you have never messed with brake fluid before DO NOT let any of the fluid touch the paint on your vehicle, it will strip it off. hope this helps

Dec 05, 2010 | 2002 Toyota Prius

1 Answer

How do i bleed the brakes


you will need another person with you. take the cap off of the master cylender, and make sure it is full of fluid. start at the wheel farthest away from the master cylender. so the back passengers side, have your partner pump the brakes about 10 times and hold pressure against the brake. ( Tell them not to let off until you tell them.) loosen the bleeder, fluid and air will squirt out, tighten bleeder screw back up, ( they can now let off of the pedal). do it over a couple or three times until you get a steady streem of fluid with no air. then go to the drivers side back, then passengers front, and end up at drivers front. Keep a check on the master cylender that it doesnt get empty, keep fluid in it or you will need to start over again.. hope i explained this good enough for you to understand.. whatever you do make sure your partner knows not to let off of the brake petal, until you have the bleed screw tight, and tell them to let off.

Nov 30, 2010 | 2000 Chevrolet Blazer

2 Answers

How to switch off engine service waring display


G'day mate i think you will find only the dealer can using a special little resistance tool which are normally to expensive for the average garage, take it for the service it new enough to look after

Apr 04, 2010 | 2009 Nissan Altima

1 Answer

97 Avalon ABS lite on TRAC lite flashes, resets w/restart of car


have your ABS system scaned for codes(intermtent code) as for the car not goin out of park when applying the brake,there is a level or linkage that works as a safety,this linkage may need adjustment.the linkeage goes from thr pedal(brake) to the shifter,some of the work thru a selenoid that gets activated when the switch is on.

Sep 10, 2009 | 1997 Toyota Avalon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...