Question about 2000 Ford Mustang

1 Answer

2000 Mustang No Low beam headlamps & No voltage on Low beam at connector.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 8,743 Answers

Check fuse and relay in engine compartment fuse box.

Please see my tip at http://www.fixya.com/cars/r6053280-lights_out_lights_not_out_bulbs_ok . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Posted on Sep 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Right side high beams not working 2000 Jeep wrangler


Is the bulb ok? The red wire with orange tracer is voltage for hi beam, on both sides. As you can see voltage for hi beam right side comes from left headlamp connector. I use a test light, headlamps on, check for voltage on red wire with orange tracer. I don't believe problem is ground, black wire or the lo beams wouldn't work, either.
headlamps-vkzpec5hhwozo4lk0la4kact-2-0.jpg

Nov 03, 2017 | Jeep Cars & Trucks

1 Answer

2008 Saturn aura wont start after trying to put rt.low lowbeam replacement


On the inside of the lid is a diagram .
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Aug 14, 2017 | Saturn Cars & Trucks

1 Answer

Right low beam headlight does not come on but my right turn signal will stay even tho i diddnt turn it on. If I cut on my high beams the rurn signal cuts off. Whats wrong? Helo


It could be the lamp control module !
Headlamps
Battery positive voltage (B+) is applied at all times to the lamp control module (LCM) through the underhood fuse block HDLP fuse.
When you place the headlamp switch in the HEAD position, the headlamps input to the LCM is grounded. The LCM then applies battery positive voltage (B+) through the underhood fuse block HDLOBML fuse and HDLOBMR fuse, which feed the left low beam headlamp and the right low beam headlamp respectively. When you activate the headlamp dimmer switch by pulling on the multifunction lever until the switch clicks, the high beam input circuit to the LCM in grounded . The LCM then removes battery positive voltage (B+) from the low beam headlamps and supplies battery positive voltage (B+) through the underhood fuse block HDHIBML fuse and HDHIBMR fuse, which feed the left high beam headlamp and the right high beam headlamp respectively.
Check this fuse in the left under hood fuse box first. HDLOBMR Fuse 18 10 Amp. RH Low Beam Headlamp . If the fuse is good check for B+ voltage with the low beams on . Use a test light or volt meter . If you look on top of fuse there are two metal tabs ,check there for B+ voltage , If no B+ voltage the LCM - lamp control module isn't supplying any .
Lamp Control Module (LCM)
Under the left side of the IP, to the right of the steering column
Turn Signal Flasher
Under the left side of the IP, to the right of the steering column
Lighting Systems Component Views in Lighting Systems
Lighting Systems Connector End Views in Lighting Systems
Turn Signal/Hazard Switch
In the left front of the passenger compartment, in the steering column

Apr 28, 2016 | 2000 Buick Park Avenue

1 Answer

I want to take out the high beem fuse for a 2003 buick regal... I lost the car manual


Two fuses HDLP L fuse #36 15amp & HDLP R fuse #32 15amp ,located in the under hood fuse / relay box. One is for Left - low an high beams an the other is for right side low an high beams . What's wrong , no high beams ?
Headlamps Inoperative - High Beams

1

Did you perform the Lighting System Diagnostic System Check?
Go to Step 2
Go to Diagnostic System Check - Lighting Systems

2

  1. Turn the ignition to the OFF position.
  2. Turn the headlamp switch to the HEAD position.
  3. Place the headlamp dimmer switch in the high beam position.
Are the high beam headlamps operating properly?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
yes Go to Step 3


Is only one high beam headlamp inoperative?
yes Go to Step 7
Go to Step 4

4

Place the headlamp dimmer switch in the flash to pass position.
Do the high beam headlamps operate in the flash to pass position?
Go to Step 13 yes
Go to Step 5 no

5

Place the headlamp dimmer switch in the high beam position.
Does the high beam indicator illuminate?
Go to Step 12
Go to Step 6

6

Test for a high resistance, an open or a short to battery positive voltage in the high beam signal circuit of the headlamp dimmer switch. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 17
Go to Step 13

7

  1. Disconnect the inoperative headlamp.
  2. Using a test lamp connected to ground, probe the battery positive voltage circuit of the inoperative high beam headlamp.
Does the test lamp illuminate?
Go to Step 8
Go to Step 9

8

Connect a test lamp between the headlamp high beam signal circuit and the battery positive voltage circuit of the inoperative high beam headlamp.
Does the test lamp illuminate?
Go to Step 11
Go to Step 10

9

Test for a high resistance or an open in the battery positive voltage circuit of the inoperative headlamp. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 17
Go to Step 12

10

Test for a high resistance or an open in the headlamp high beam signal circuit of the inoperative high beam headlamp. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 17
Go to Step 12

11

Inspect for poor connections at the harness connector of the inoperative headlamp. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 17
Go to Step 14

12

Inspect for poor connections at the harness connector of the fuse block - underhood. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 17
Go to Step 15

13

Inspect for poor connections at the harness connector of the headlamp dimmer switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 17
Go to Step 16

14

Replace the inoperative headlamp. Refer to Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement .
Did you complete the repair?
Go to Step 17
--

15

Replace the fuse block - underhood. Refer to Underhood Electrical Center or Junction Block Replacement in Wiring Systems.
Did you complete the repair?
Go to Step 17
--

16

Replace the headlamp dimmer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column.
Did you complete the repair?
Go to Step 17
--

17

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jan 07, 2016 | Buick Cars & Trucks

1 Answer

Low beams dont work and only one high beam works


Do you know how to do voltage drop testing ? Leave the blubs in there sockets turn the low beams on , measure voltage on the power side , LH low beam yellow with black stripe an for the RH low beam dark blue wire . If you have battery voltage there, power side is good . Then check ground side both are yellow wires , test with lights on . if you see 6 volts , 12 volts .anything more then .03 millivolts you have a ground side problem . The lights ground through the light switch .
Low Beam
Voltage to the headlamp switch is available at all times from the HDLP SW fuse 7 through CKT 1940 (ORN). When the headlamp switch is turned to the HDLP position, the headlamp power relay coil is energized through CKT 352 (WHT). A signal is also sent to the body control module (BCM) that the headlamp switch is ON. When the headlamp switch is in the AUTO or PARK position, the ambient light sensor (located in the right speaker grill) senses either daylight or darkness and sends the signal to the BCM. When the Ambient Light Sensor detects a dark condition, the BCM produces a signal that will energize the headlamp power relay through CKT 352. The relay coil is grounded through terminal F7 connector 2 of the underhood fuse block to CKT 350 (BLK) to G102. When the headlamp power relay is energized the relay supplies power to the LT HDLP and RT HDLP fuses. The RH low beam headlamp receives current through CKT 198 (DK BLU) from the RT HDLP fuse. The LH low beam headlamp receives current through CKT 712 (YEL/BLK) from the LT HDLP fuse. Both headlamp low beam bulbs are grounded by CKT 524 (PPL) through the underhood fuse block to the multifunction switch (low position) contacts through CKT 10 (YEL) to the headlamp grounding relay in the body relay block through the normally closed contacts to CKT 1850 (BLK) to G200.

Oct 14, 2015 | 1999 GMC Sonoma

1 Answer

2006 buick allure , automatic low beams do not come on when key starts car


Headlamps
You can use the headlamps two different ways.
?€¢
Place the headlamp switch in the HEAD position for normal operations


?€¢
Place the headlamp switch in the OFF position for automatic lamp control (ALC) operation. During ALC the low beam headlamps are ON for daytime running lamp (DRL) operation in daylight conditions at reduced intensity or low beam headlamps ON at full intensity with exterior park lamps ON in low light conditions. The ambient light sensor is a light-sensitive transistor that varies its voltage signal to the body control module (BCM) in response to changes in the outside (ambient) light level. When the BCM receives this signal the BCM turns ON just the low beam headlamps at reduced intensity for the daytime running lamp (DRL) operation. A resistor wire is used (CKT312) to reduced the voltage which reduces the light intensity for the DRL's function. The ambient light sensor can also turn ON the low beam headlamps and the exterior lamps for automatic lamp control (ALC). Any function or condition that turns ON the headlamps will cancel the DRL operation (this means no reduced voltage to the low beam lights). Thirty seconds after you start the engine with the headlamp switch in the OFF position, the DRL will perform one of two actions:
?€¢
Illuminate the low beam headlamps at reduced intensity in daylight conditions


?€¢
Illuminate the low beam headlamps and exterior park lamps for low light conditions

The DRL operates when the ignition switch is in the RUN position, the parking brake is not set and the transmission is not in the PARK position When these conditions are met and the DRL ambient light sensor indicates daylight conditions the DRL will illuminate
Should have BCM scanned for DTC'S - diagnostic trouble codes , could have DTC'S stored in memory !
DTC B2645 Ambient Light Circuit
The body control module (BCM) monitors the ambient light sensor signal circuit in order to determine if the daytime running lights (DRL) or the auto headlights (ALC) should be turned ON in the AUTO mode. When the BCM senses the ambient light sensor voltage is between 1.75-4.9 volts, either the DRL will be commanded ON or the ALC will be commanded ON.

  1. Turn ON the headlamps.
  2. Ensure that the headlamp dimmer switch is in the LOW position.
Do both low beam headlamps illuminate?
Is only one low beam headlamp inoperative? YES / NO
IF no
  1. Disconnect the lamps switch assembly.
  2. Install a jumper between the headlamp switch headlamps ON signal circuit and ground.
Do the low beam headlamps illuminate?
Do the low beam headlamps illuminate?
Go to Step 18
Go to Step 7

7

  1. Remove the headlamp module.
  2. Install a fused jumper between battery positive voltage and the switched low beam voltage supply circuit.
Do the low beam headlamps illuminate?
Go to Step 8
Go to Step 11

8

Test for the following in the headlamp module control circuit:
?€¢
An open


?€¢
A poor connection


?€¢
A short to ground

Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 10

9

Inspect for a poor connection at the harness connector of the lamp switch assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 14

10

Inspect for a poor connection at the headlamp module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 15

11

Test for a short to ground in the low beam voltage supply circuit. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 12

12

Inspect for a poor connection at the harness connector of the underhood fuse block. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 17

13

Inspect the inoperative low beam headlamp voltage supply and ground circuit for a high resistance, a short to ground, or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 16

14

Replace the lamp switch assembly. Refer to Headlamp Switch Replacement .
Did you complete the replacement?
Go to Step 19
--

15

Replace the headlamp module. Refer to Relay Replacement in Wiring Systems.
Did you complete the replacement?
Go to Step 19
--

16

Replace the inoperative low beam headlamp. Refer to Headlamp Assembly or Headlamp Bulb Replacement .
Did you complete the replacement?
Go to Step 19
--

17

Replace the underhood fuse block. Refer to Testing for Intermittent Conditions and Poor Connections .
Did you complete the replacement?
Go to Step 19
--

18

Replace the BCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?
Go to Step 19
--

19

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 3

IF

Sep 30, 2015 | Buick Cars & Trucks

1 Answer

Were is headlight low beam relay


It is located in the under hood fuse/relay box . It's non -replaceable ,if bad whole fuse box has to be replaced ! The low beam headlamps may be turned ON in 3 different ways:
?€¢
When the headlamp switch in the HEAD position for normal operations


?€¢
When the headlamp switch is in the AUTO position, for automatic lamp control (ALC)


?€¢
When the headlamp switch is placed in the AUTO position, with the windshield wipers ON in daylight conditions, after a 6 second delay

Battery voltage is applied at all times to the coil and switch sides of the LOW BEAM PCB Relay located in the underhood fuse block. When the headlamp switch is placed in the HEAD position, ground from G202 is applied through headlamps ON switch signal circuit to the body control module (BCM), signaling the headlamps ON request. In response to this signal, the BCM applies ground through the headlamp low beam relay control circuit energizing the low beam relay. With the relay energized, battery voltage is applied through the switch side of the relay, the left and right low beam fuses, and the low beam supply voltage circuits illuminating the low beam headlamps. Ground for the left headlamp is provided at G101 and the right headlamp at G100.
Low Beam Relay Test

  1. Ignition OFF, disconnect the C2 harness connector at the underhood fuse block.
  2. Connect a test lamp between the control circuit terminal A5 and B+.
  3. Ignition ON, command the Low Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
  4. ?‡'
    If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.


    ?‡'
    If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.

  5. If all circuits test normal, replace the underhood fuse block.
  6. Ignition OFF, disconnect the harness connector at the inoperative low beam headlamp. Test for less than 5.0 ohms between the ground circuit terminal B and ground.
    ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

    Connect a test lamp between the supply voltage circuit terminal A and ground. Ignition ON, command the Low Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
    ?‡'
    If the test lamp is always ON, test the supply voltage circuit for a short to voltage. If the circuit tests normal, replace the underhood fuse block.


    ?‡'
    If the test lamp is always OFF, test the supply voltage circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the underhood fuse block.

    If all circuits test normal, test or replace the low beam headlamp.

Jun 10, 2015 | 2006 Chevrolet Chevrolet Impala LS

1 Answer

How do I fix the tail lights and headlights on my 2000 Chevrolet CavalierI have brake lights and turn signals


Did you check the fuses RT HDLP 15amp. LTHDLP 15amp in the instrument panel fuse block ? These are for the headlamps ! Also check EXTLAMP fuse 20amp in same fuse block. If those are good your going to need a Headlamp switch . I could tell you to check for battery + voltage at connector 1 pin D an F at the headlamp switch with park lamps on ! this is to see if voltage is going through the switch . You could do the same for the headlamps , Connector 2 pin C is low beams an pin B is high beams ! Connector 2 pins A an E are grounds , need to check those as well . But first you'll need to take plastic cover from around the upper steering column to get at the switch ! piece of cake ! good luck ....

Mar 07, 2015 | 2000 Chevrolet Cavalier

1 Answer

My headlights dont work,.all other lights are fine though,.is it the fuses or the bulbs? im not sure what fuses they would be,.there seem to be different ones for the same thing


do your flash to pass lamps light when you pull the stalk towards you? If yes, the bulbs are ok.
Do the hig beams work?
Your headlamps have sepaerate fuses for each headlamp and you have a low beam relay and a high beam relay under the hood in the black box.
If everything is out, I suspect a bad headlamp switch.
Check car-part.com and look on page with * for cheapest price.

Your owner manual will identify fuses & relays.

PS, You did not recently instal high current bulbs did you? If yes, put originals back in.

HEADLAMPS

The voltage is supplied to the lamp switch through a fuse. This fuse is located in the central junction box in the left-hand footwell.
When the headlamps are switched on, a voltage is supplied to the high beam/low beam switch and to the low beam relay. The relay for the low beam is located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "low beam", then a voltage is supplied through the low beam relay to the low beam part of the headlamp assembly. The left and right-hand low beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "high beam", then a voltage is supplied through the high beam relay to the high beam part of the headlamp assembly. The left and right-hand high beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.

----------------------------------------------------------------------------------------------------------
Lamp Switch
Removal
  1. s2y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
    Remove the lower driver's side footwell trim.
  1. Detach the lamp switch bezel.
    • Remove two screws.
  1. Remove the light switch.
    • Remove three screws.
    • Disconnect the electrical connector

Feb 23, 2009 | 2005 Ford Focus

1 Answer

Headlights dim


https://s1.postimg.org/1i7q5btlu7/headlamps.jpg

Click on the link.
The top wires to headlamp are voltage for hi or lo beam.
The bottom black wire is ground. You can use a test light to check voltage and ground.

Oct 29, 2017 | 1998 Ford Windstar

Not finding what you are looking for?
2000 Ford Mustang Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5575 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...