The windshield wipers bang - 2000 Honda Accord

Wiper/Washer System Components
The Wiper/Washer System consists of the following electrical components:
• Accessory relay
• Heated washer nozzles w/XA7
• WASH NOZ 10A fuse
• Windshield washer fluid level switch
• Windshield washer pump motor
• Windshield wiper motor
• Windshield wiper motor module
• Windshield wiper/washer switch
• Wiper/washer switch 10A fuse
• Wiper motor 30A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all modes. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits. The windshield wiper switch signal circuit voltage levels to the wiper motor module determine the wiper motor operating mode.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.

The is the symptom of a defective wiper switch.

Principles of Operation
The windshield wiper motor receive inputs from the following:

• multifunction switch
• lighting control module (LCM)
• ignition switch
• battery junction box (BJB)
• central junction box (CJB)

The following components are integrated into the windshield wiper motor:

• windshield wiper motor module
• high/low speed relay
• run/park sensor (Hall effect)
• washer pump relay

High Speed Windshield Wipers
High speed is activated when the multifunction switch supplies ground to the windshield wiper motor module inputs. The windshield wiper motor module then supplies ground to the run/park sensor and high/low relay coil, activating the relay with voltage supplied from the ignition switch (RUN/ACC) through the central junction box (CJB). When the windshield wiper motor module receives voltage from the run/park sensor, it removes ground from the run/park sensor, deactivating it. The windshield wiper motor continues to operate from voltage connected through the run/park sensor until the Hall effect senses the magnet in the motor. When the Hall effect senses the magnet in motor the windshield wiper motor returns to the park position, the internal run/park sensor grounds the windshield wiper motor module input and the windshield wiper motor module removes ground from the windshield wiper high/low relay coil, deactivating the high/low relay and windshield wiper motor. The windshield wiper motor module continues to cycle the windshield wipers until the inputs from the multifunction switch are changed from the high speed position.
Low Speed Windshield Wipers
Low speed is activated when the multifunction switch supplies a specific ground to the speed inputs of the windshield wiper motor module. The windshield wiper motor module then supplies ground to only the windshield wiper run/park relay coil, activating it. When the windshield wiper run/park relay is activated, the deactivated windshield high/low relay connects voltage to the windshield wiper motor low input activating the wiper motor. The windshield wiper motor module continues to operate the windshield wiper motor in the same manner as in high speed, but in low speed with the wiper motor connected to the low speed input.
Intermittent Speed Windshield Wipers
The intermittent wiper speed is activated with grounds controlled by the multifunction switch inputs to the windshield wiper motor module. The windshield wiper motor module then activates the windshield wiper run/park relay coil and switches voltage through the windshield wiper high/low relay. The high/low relay remains deactivated, supplying the voltage to the wiper motor low speed input and activates the windshield wiper motor. When the windshield wiper motor module receives the grounded input, the motor continues to operate until Hall effect sensors senses the wiper motors magnet, which turns off the run/park sensor output to the windshield wiper run/park software, deactivating the relay and disconnecting voltage to the wiper motor. The windshield wipers remain parked until the windshield wiper motor module completes a time-out and then repeats the intermittent windshield wiper cycle.
Washer System
The windshield washer is activated by the internal wiper motor module when it receives a ground from the multifunction switch between the washer input. Dependent on the correct ground, the internal wiper motor modules activates the windshield washer relay (internal) by grounding the respective relay coil. When the relay is activated, it connects voltage to the washer pump while the washer level switch provides ground to the washer pump.
Default Mode
The windshield wiper motor defaults to this mode when the run/park sensor does not sense the hall effect magnet inside wiper motor. This can be caused by obstruction of the windshield wipers or a binding linkage. The windshield wiper motor will continue to operate in a high/low speed condition for a period of 60 seconds.

Symptom Chart
Symptom Chart Condition Possible Sources Action

• The wipers are inoperative

• Multifunction switch
• Circuitry
• Ignition switch
• Windshield wiper motor

• Go To Pinpoint Test A .

Do you know how to test automotive electrical circuits using a factory diagnostic test procedure flow chart ?

PINPOINT TEST A: THE WIPERS ARE INOPERATIVE Test Step Result / Action to Take A1 CHECK CIRCUITS 65 (DG) AND 2025 (RD/YE) FOR VOLTAGE

• Key in OFF position.
• Disconnect: Windshield Wiper Motor C125.
• Key in ON position.
• Measure the voltage between windshield wiper C125 pin 5, circuit 2025 (RD/YE), harness side and ground; and between windshield wiper motor C125 pin 8, circuit 65 (DG), harness side and ground.
• Are the voltages greater than 10 volts?

Yes
GO to A2 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A2 CHECK CIRCUITS 57 (BK) AND 676 (PK/OG) FOR OPENS

• Key in OFF position.
• Measure the resistance between windshield wiper C125 pin 6, circuit 57 (BK), harness side and ground; and between windshield wiper motor C125 pin 3, circuit 676 (PK/OG), harness side and ground.
• Are the resistances less than 5 ohms?

Yes
GO to A3 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A3 CHECK THE MULTIFUNCTION SWITCH

• Disconnect: Multifunction Switch C202b.
• Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  
• Does the multifunction switch pass the component test?

Yes
GO to A4 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . A4 CHECK CIRCUIT 57 (BK) FOR AN OPEN

• Measure the resistance between C202b pin 5, circuit 57 (BK), harness side and ground.
• Is the resistance less than 5 ohms?

Yes
GO to A5 .

No
REPAIR the circuit. TEST the system for normal operation. A5 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR OPENS

• Using the following table, measure the resistance between the multifunction switch C202b harness side and the windshield wiper motor C125 harness side:
  
  Multifunction Switch C202b Windshield Wiper Motor C125 pin 6, circuit 56 (DB/OG) pin 10, circuit 56 (DB/OG) pin 3, circuit 58 (WH) pin 11, circuit 58 (WH) pin 1, circuit 61 (YE/RD) pin 1, circuit 61 (YE/RD) pin 4, circuit 63 (RD) pin 9, circuit 63 (RD)
• Are the resistances less than 5 ohms?

Yes
GO to A6 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A6 CHECK FOR CORRECT WIPER MOTOR OPERATION

• Disconnect all wiper motor connectors.
• Check for:
  • corrosion
  • pushed-out pins
• Connect all wiper motor connectors and make sure they seat correctly.
• Operate the system and verify the concern is still present.
• Is the concern still present?

Yes
GO to A7 .

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. TEST the system for normal operation. A7 CHECK THE WINDSHIELD WIPER MOTOR

• Key in OFF position.
• Disconnect: Windshield Wiper Motor C125.
• Carry out the windshield wiper motor component test as outlined in this section.
• Does the windshield wiper motor pass the component test?

Yes
The system is operating correctly at this time. The concern may have been caused by binding or incorrect pivot arm adjustment. REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section.

might be someone took the whole arm off to paint em or whatever so while they are in the off position check to make sure they don't need a quick adjustment for example if they are flat/level with the windshield lower seal if they are than you got the wrong size blades if they are off a little than remove clip holding the windshield wiper arm and slide off of the cog and move it a couple teeth till its flat than check your work by turning the wipers on if they aren't perfect than keep adjusting till they are on both sides

It sounds as if the wiper linkage has come adrift, normally will require renewal of a link arm

the arms are pressed onto the transmission linkage of the wiper motor. Most likely the nut can be loose holding the arm on and needs to be tighten up. I would loosen it first to be sure the threads are not stripped first before tightening up. If stripped it will need a replacement instead to prevent this noise

Either looseness of the linkage or install error. If Windshield has been replaced, sometimes they miss align the wiper arm.....

why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.

1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.

1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.

1. Remove left windshield wiper adapter and connecting arm clip access cover.

1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
   

----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal

1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.

1. Disconnect battery and wiper motor electrical connector.

1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .

1. Disconnect the battery ground cable (14301).

1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .

1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.

1. Reach through the access cover opening and unsnap the wiper motor clip.

1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.

1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.

1. Remove nut and ground strap.

1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .

Installation

1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).

1. Install nut and ground strap.

1. Connect wiper motor electrical connector.

1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.

1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.

1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.

1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
   

1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.

1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.

1. Test the system.

There is a 10mm nut on the wiper where it connects to the post near the hood. Unscrew it and lift the arm off of the post. Turn it just a little up and put it back on the post. Screw the nut back on and it should work.

• Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF

• Damaged turn signal and windshield wiper switch .
• Damaged windshield wiper motor .
• Damaged windshield wiper control module.

Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
Windshield Wiper System The windshield wiper system consists of :

• Windshield wiper motor (17508) (F-type).
• Washer system.
• Windshield wiper control module.
• Turn signal and windshield wiper switch (13K359).

The windshield wiper control module is:

• Located at the instrument panel fuse panel.

The windshield wiper motor is:

• Attached to the cowl top extension (021A36) .
• Connected to windshield wiper mounting arm and pivot shaft (17566) .

The turn signal and windshield wiper switch features a:

• Rotary wiper switch.
• Push type washer actuator.

OFF/Low/High Speed

• Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
• The windshield wiper motor has a brush rigging that permits selection of low or high speed.
• When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
• When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
• In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
• When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
• When the park switch contacts open, the windshield wiper motor stops in the park position.

Interval
When the turn signal and windshield wiper switch is in the interval position:

• The wipers make single wipes separated by pauses.
• The rotary switch is on the end of turn signal and windshield wiper switch .
• The length of the pause can be set from approximately 1 to 17 seconds.
• Length of pause decreases as the rotary switch is rotated away from off.
• Length of pause increases as the rotary switch is rotated toward off.

While in the interval wiper mode:

• It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.