Question about 2006 Ford Mustang

Open Question

After changing the battery on my 2006 mustang GT idle speed is too low

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75822 Answers

SOURCE: speed sensor removal 94 Mustang GT

Remove the trans cross member and let the trans drop down (use a floor jack), then you will be able to access it.

Posted on Sep 23, 2008

bigdemille
  • 15 Answers

SOURCE: 2006 Mustang GT 4.6L codes P0010,P0012,P0016,P0020,P0171, P0174

my mustang had problems after i put an exhaust on it. if this is the case for you go down under your car it has 2 sensors up high on each exhaust pipe get the size then go down to an auto parts store and get some spark plug reducers and screw your o2 sensors into them and back into your exhaust

Posted on Jun 08, 2009

  • 76 Answers

SOURCE: High Idle/low speed miss

look for a diagram under the hood follow the route for each vacum . you have a intake leak take your time and go over each side of the engine even plastic air line could be cracked

Posted on Aug 17, 2009

  • 1 Answer

SOURCE: 2006 Mustang GT engine reving Problem

check the throttle body butterfly for excessive dirt build up. Mine had a rolling idle and would want stall in the mornings. The dealer said it was due to my aftermarket tuner and cold air intake..............just a dirty throttle body that i cleaned.

Posted on Sep 24, 2009

MNfisherman
  • 11896 Answers

SOURCE: low idle

Most often, dirty or faulty 02 sensors will throw off the idle. The 02 sensors and camshaft position sensor basically control all the idle. If TPS was dirty or bad, you would have some hesitation when giving some gas. Bad plug would cause lack of power or misfire.

Posted on Oct 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Idle surging down a little when at stop lights in my 2000 mustang 3.8 never dies but seem's close.every 6 to 10 seconds no difference noticed while driving down the road. changed AIC valve for a c


probably cause by the a/c cutting in and out or running at idle . Fit an idle compensator to the system throttle or raise the idle speed 300rpm.

May 26, 2013 | 2000 Ford Mustang

1 Answer

What's the steps to do an idle re-learn on a 2007


Hold the idle at 2000 RPM for 2 minutes then drop it to 1500 for 2 minutes and then 1000 for 2 minutes, then let it return to idle for 5 minutes. Full relearn requires some driving as well, mixed low and highway speed and idle time.

Feb 14, 2012 | 2007 Ford Mustang GT California Special...

1 Answer

I changed the battery in my 2006 mustang gt and now the wrench light is on and I cannot excellerate. I tried disconnecting the negative battery cable and it allowed the vehicle to remain idling, but the...


i just had the same problem...the wrench light means the car is in "limp home" mode and i had to replace my throttle body assy....$165 on ebay at blueovalindustries

Feb 27, 2011 | 2006 Ford Mustang

1 Answer

2006 Ford Mustang GT 4.6 liter can jump off


its most likey your altenator there =s no charge going to the batt

Dec 19, 2009 | 2006 Ford Mustang

1 Answer

Low idle. 78,000mi recent very low idle almost stalling. Hwy miles 2006 GT. plugs never changed. TPS not changed or cleaned nor throttle body. Did replace a battery early in the year.


Most often, dirty or faulty 02 sensors will throw off the idle. The 02 sensors and camshaft position sensor basically control all the idle. If TPS was dirty or bad, you would have some hesitation when giving some gas. Bad plug would cause lack of power or misfire.

Oct 21, 2009 | 2006 Ford Mustang

1 Answer

2006 mustang gt


After you change the battery,the computer has to
re-learn the idle.it takes between 10-20 miles of driving to re-learn.you can clean the throttle body too,they get sludged up and change air flow and idle.

Oct 02, 2009 | 2006 Ford Mustang

2 Answers

High Idle/low speed miss


look for a diagram under the hood follow the route for each vacum . you have a intake leak take your time and go over each side of the engine even plastic air line could be cracked

Aug 17, 2009 | 1999 Ford Mustang Cobra

2 Answers

2006 Mustang GT engine reving Problem


check the throttle body butterfly for excessive dirt build up. Mine had a rolling idle and would want stall in the mornings. The dealer said it was due to my aftermarket tuner and cold air intake..............just a dirty throttle body that i cleaned.

Apr 03, 2009 | 2006 Ford Mustang

Not finding what you are looking for?
2006 Ford Mustang Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...