Question about 1996 Pontiac Grand Prix

1 Answer

Changed radiator hose and cant get air out how do you bleed the air out 1996 pontiac grandprix

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Pontiac Master
  • 540 Answers

I just usually add coolant while its running, it will spew some out a few times, but after it warms up enough you will get it full

Posted on Sep 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 toyota rav 4 cooling system problem


COOLING SYSTEM MY NEED A VACCUM BLEED...TO GET RID AIR POCK

Jun 26, 2014 | 1996 Toyota RAV4

1 Answer

How to change a bad thermostat on a 2003 3.4L pontiac montana


put in a radiator flush ,run it for 20 miles it can be a blocked core in both the radiator and the heater.that should clean it. then refill with a 50/50 mix anti freeze then bleed it of air. put your heater on full .run the engine on tick over.then push in the radiator hose to push the air out of the expansion bottle cap .it is off . then refit your cap.

Dec 30, 2013 | 2003 Pontiac Montana

1 Answer

Engine overheating, replaced cracked radiator w/new but problem persists, where is the thermostat located?


should be on right side(drivers side) of plentum. Follow top radiator hose. Area is kind of hard to get to but is a real an easy change. After you change the thermostat then crank engine and bleed air using the bleed screws that are located in middle left of plentum.

Nov 21, 2013 | 2008 Pontiac Grand Prix

1 Answer

1996 acura tl 3.2 overheats and no heat in car\


Have you recently changed your engine coolant? Have you checked your engine coolant? If you just changed the coolant you probably have an air lock in the system and it needs bleed out. To do this i would need to know more info about the vehicle. Another possibility you could have a coolant leak, IE the water pump, radiator hose, heater hose leak. with low coolant the radiator can't do its job and cool the engine. You could also have a broken water pump impeller. No impeller no engine coolant flow threw the engine and heater core.

Nov 09, 2012 | 1996 Acura TL Series

1 Answer

Bleeding the cooling system


look at your top radiator hose is there a small bleed valve at the top of the thermostat housing when the upper hose attaches to? If so loosen the bleed valve and allow the cooling system to purge the air out of the system you can tell when the air is out of the system when a steady stream of coolant starts to flow out of the bleed valve, if there is no bleed valve take the top radiator hose off of the engine side and allow the cooling system to purge the air out through the top of the engine that way

Jul 26, 2012 | 1996 Pontiac Grand Prix

1 Answer

Where is the bleed valve located on a 1998 pontiac grand prix 2.8 engine? The auto parts store has never heard of a bleed valve.


Was the thermostat changed? I would suggest replacing the thermostat refill the system with new coolant and purge the air out of the system.

Mar 09, 2012 | Cars & Trucks

1 Answer

ENGINE WAS RUNNING HOT AND WHEN I CHECKED UNDER THE HOOD THE LOWER RADIATOR HOSE WAS COLAPSED


A collapsed hose will restrict (or completely block) water flow, causing a overheating condition. Before you do anything else, replace the hose. Some aftermarket hoses are available with a wound steel coil that will prevent a hose from collapsing.

Good time to replace all the hoses and thermostat. If I were you, I'd also flush the cooling system while I was at it. Probably wouldn't be a bad idea to take a look at your serpentine (or "v") belt to.

If your particular vehicle has air bleed ports, be sure to properly bleed all air from the system when refilling with coolant. Usually the bleed ports will at or near the point of attachment of both the upper and lower radiator hoses to the engine block.

Good luck!

Feb 23, 2011 | Pontiac Grand Prix Cars & Trucks

1 Answer

Where is the A/C drier (accumulator) located on a 1996 Grand Am 2.4? Thanks


look for two hoses or pipes coming out of the firewall side by side (from inside the car) .. one pipe is small the other is large .. follow the large pipe/hose .. it will attach to the drier (about midway between the firewall and the radiator) .. another hose/pipe will attach to the other side of the drier and that goes to the condenser (in front of and similar to the radiator) ... in order to change the drier you must first bleed off any refrigerant left in the system .. its not legal to do that yourself .. you have to have someone "certified" and they have to recover the gas (they cant bleed it to atmosphere) .. if your system is already at zero pressure then replacing the drier is easy but requires a vacuum pump operating for at least 2 hours (longer in cold weather) before new refrigerant is added .. you can test for leaks by observing if it can hold a vacuum for 15 min or so without dropping .. all refrigerant is added and pressure tested via the valve port mounted on that large pipe (you will see a screw-on plastic cover similar to, but larger than, a tire valve cover .. R134a refill hoses will fit only that port ..

Jul 05, 2010 | 1996 Pontiac Grand Am

2 Answers

Engine overheating


The best way to flush it would be to take off the bottom radiator hose and pump water through the fill nozzle after all the coolent is out you can then hook the hose back up and replace it with new coolant.

Feb 01, 2009 | 2000 Pontiac Grand Am GT

1 Answer

Coolant pouring out surge tank


if one radiator hose gets hot and the other doesnt, the the thermostat is shot, but you said you replaced it, it is possible the thermostat has been put in backwards

Nov 21, 2008 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
1996 Pontiac Grand Prix Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...