Question about 1996 Isuzu Rodeo

1 Answer

Won't start the clutch went out so I replaced it! I changed afew other parts like the distributer, now it won't start shop says it might be the brain not sure? What should I do?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 359 Answers

Did u put the distributer in the correct position being when the engine is on top dead centre the rotor button should point to no1

Posted on May 23, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a ford fiesta r reg its had a new clutch the clutch has only been in for a week and half i started having problems when i went to go shopping i put it into gear and i only had a little bite

Who replaced the clutch? if it was a shop then I would take it back for them to fix, If you changed it yourself was there oil on the old clutch and if so did you repair the oil leak. I.e. hyd clutch or transmission seal. Hope this helps.

Apr 14, 2015 | Ford Fiesta Cars & Trucks

1 Answer

Trouble shoot 2500masda truck that won t start after I replace clutch and slave cylinder

Did you reconnect the wires and re-position the clutch safety switch at the clutch pedal assembly? If this switch is not positioned or connected correctly it will not allow the truck to start.

Feb 25, 2015 | 1999 Mazda Pickup

1 Answer

Transmission Issues? Feels like I'm dumping the clutch when I ease into gear. Please help!

Sounds like something broke in the clutch area. The clutch has springs in it. In there for harsh shifts And dumping the clutch. But the pressure plate could possibly do this as it is also spring loaded. Changing the fluid would do this. The fluid only lubricates the internal parts. IE.. gears, bearings, ad synchronizers. being low isn't good, but still wouldn't cause this problem.

Feb 18, 2015 | 1999 Dodge Dakota

1 Answer

Won't start

Check the fuel injectors, with the key on one side of the two wire connector will have battery voltage, if none is present then check the ECM fuses in the underhood fuel box.

Jun 22, 2017 | 1999 GMC Sonoma

1 Answer

1999 chevy k2500. changed spark plugs 4 times in 7 months. Runs good for a week then doesn't start. Changed spider, throttle body sensor. Still has no codes and once again won't start.

The next time it won't start ,pull a sparkplug wire and see if you're getting fire.Then we'll known whether its a ignition or fuel problem and go from there.

Jan 11, 2012 | 1999 Chevrolet K2500

2 Answers

Wont crank, gages work lights work, clutch depressed

Check starter relays. Should be under the hood on the d/s fender well. You will need a helper. if its not working and you don't know how to check the wiring to it get back to me

May 16, 2011 | 1994 Jeep Grand Cherokee

2 Answers

Replaced clutch. then went to start no spark. checked with many test with distributer and the throtal position sencer. checked signal from the sencer to the ecm and we go the sqaure wave pattren. but the...

Make sure you did not get any wires pinched between engine & bellhousing this is common.If it started and ran before doing clutch, nothing you did should change that! Are all wires back on starter motor?

Feb 26, 2009 | 1997 GMC Savana

3 Answers

1992 Honda Accord DX will not start, gets spark, gets fuel

check if its getting spark if it is i would check the main relay very common problem .if no spark then i would check the ignition ignitor located in the distributor one last thing to check would be the ignition switch

Feb 25, 2009 | 1992 Honda Accord

2 Answers

Car won't start!

check your starter motor is fitted correctly & also your starter motor are correctly fitted

May 23, 2008 | 1996 Isuzu Rodeo

Not finding what you are looking for?
1996 Isuzu Rodeo Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14403 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides