Question about 1996 Isuzu Rodeo

2 Answers

Car won't start!

2.6ltr clutch replaced now car won't start
shop says it could be brain but not sure
can not hook it up to a scope unless it is running?
What should I do?
It ran before clutch went out.

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Ok first off any good mechanic can diagnose a no start problem and most places just assume its the computer because they don't know how to diagnose the problem. The computer buy the way is the least likely cause  and if it started before you took it to the shop they are responsible for fixing it . More than likely its just a wire that did not get plugged in or a sensor went out from setting Or a switch that is miss adjusted or God knows what but it can be diagnosed if your trained .Look for the (ASE) certified sign.                                       (Automotive Service Excellence)     -Will

Posted on Jun 06, 2008


Check your starter motor is fitted correctly & also your starter motor are correctly fitted

Posted on May 24, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My car starts just replaced an altenator belt and now the car wont shift into gear is making a grinding noise

Presumably manual transmission.

Car probably won't go into gear because the clutch is stuck or won't clear.

There is no obvious connection between the alternator belt and the clutch unless perhaps being careless in the engine compartment the clutch hydraulic pipe or cable adjustment got damaged.

Feb 11, 2018 | Cars & Trucks

1 Answer

Honda accord lx2003the motor ,clutch, and brain box were replaced. Now the car will not start.dealership said its the security immobilizer not communicating. What does this mean and how do I fix it?

Did the dealer do all the work and now they tell you this? Take it back talk to the service manager. no help? Talk to the general manager. Other repair shop, the same effort. DIY? Ouch.

Apr 14, 2015 | Honda Cars & Trucks

1 Answer

Cold starting

Testing the fuel system ,fuel pressure an flow , voltage drop testing the electrical . Hooking up a factory scanner an checking engine mangagement sensor data . Doing these thing's is the way to finding the problem . Not guessing an looking for common problem's .Their are no magical fixes for auto repair . Viewing wiring diagram's an getting out the testing equipment , DVOM - digital volt ohm meter , scanner , lab scope etc... Your best bet ,take it to a qualified repair shop .

048 Engine Hard to Start or No Start Scan Data for Starting Problems
047 Engine Hard to Start or No Start Scan Data for Ignition
Testing Electric Fuel Pump Problems with Voltage Drop Test

Dec 24, 2017 | 2002 Chevrolet Cavalier Coupe

2 Answers

My clutch wont go into any gear unless i force it.. And it grinds on going in reverse. is it the master/slave cylinder the problem. or the clutch? please help!!!

Hopefully you got a warranty with the clutch job, so I would take it back to that shop first. If you have someone else work on the truck the first shop is off the hook for responsibility. Its possible the clutch has failed, or you have developed a new problem.

Jan 17, 2014 | 1990 Toyota 4Runner

1 Answer

Suzuki won"t shift into gear unless I turn the car off and put it into first

make your adjustment to clutch, see how that works, but start saving up for a new clutch, or just have your inspection mechanic, take a look @ it for you, make the adjustment, and he can remove a cover and inspect the condition of your clutch with his own eyes. its a lot easyier for him than you. then, you'll know for sure. good luck

Jan 13, 2013 | 2001 Suzuki Grand Vitara

1 Answer

Wont hit a lick is firing fuel system wont run unless u hot wire and the spot for relay is dead and has new engine brain still nothing.

Try changing the electronics on your ignition switch. All of the power to the rest of your car goes through your ignition switch and if the switch is bad the car won't start because power is not getting to where it needs to be. I am almost positive that if you replace the ignition switch electronic your car will run fine. I hope this helps

Aug 26, 2011 | 2002 Kia Sportage

1 Answer

2002 impala 3.8L 180,000kms. Having problems with car hesitating on acceleration(not all the time). Had maf sensor & idle air control sensor replaced recently. Fuel filter, air filter,new plugs &...

it is possibly the throttle position sensor(tps) malfunctioning. basically the computer or "brain" of the car thinks the throttle is in a different position than it really is and automatically makes adjustments to fuel, air ect.... based on these false readings from the sensor thus causing the engine to react a little different when you expect to have power.

May 14, 2011 | 2002 Chevrolet Impala

1 Answer

Won't start

did u put the distributer in the correct position being when the engine is on top dead centre the rotor button should point to no1

May 23, 2008 | 1996 Isuzu Rodeo

Not finding what you are looking for?
1996 Isuzu Rodeo Logo

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14411 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides